Current issue: 53(4)
Under compilation: 54(1)
According to the Swedish Timber Measurement Act, measurements affecting payments for wood fuels to landowners must be accurate and precise. In this regard, moisture content is an important quality parameter for wood chips which influences the net calorific value as received and thus the economic value. As standard practice moisture content is determined with the oven-drying method, which is cumbersome to use for deliveries to facilities without drying-ovens, which in turn necessitates that samples are taken elsewhere for measurement. An alternative solution is to use a portable moisture meter. Our aim was to evaluate the precision of a handheld capacitance moisture meter. Accuracy and precision of a capacitance meter was determined in the lab and a calibration function was made. Thereafter, the calibrated moisture meter was compared with the standard method for moisture content determination of truckloads of chips. The capacitance meter showed a moderate accuracy by underestimating moisture content by 6.0 percentage points (pp), compared to the reference method, at a precision of ±3.8 pp (CI 95%). For chips with M > 50%, both accuracy and precision decreased. Calibration increased the accuracy in the follow up study by 3 pp for chips with M < 50% but could not be made for wetter chips. The oven-drying method and the capacitance meter can provide equally accurate estimates of mean moisture content for chips with M < 50% if a larger sample is taken with the latter. It should be possible to use capacitance meters to measure moisture content even when used to calculate payments depending of the needed accuracy. A calibration function for each assortment is needed.
Boom corridor thinning (BCT) has been proposed as a cost-effective technique for biomass thinning (BT) in young dense stands. The objective of this study was to determine how various BCT operations affect stand structure following biomass thinning and to compare the results with conventional selective thinning methods. Two series of field experiments were established; BCT 1-series: Three sites in south of Sweden (9 and 11 m in mean and dominating tree height) with five treatments, including a control, conventional selective thinning and three BCT treatments (1 m and 2 m wide corridors and selective BCT). The second BCT series: Three regions in Sweden (in the north, centre and in the south), with two stand sites in each region with different tree heights (4/9 m and 5/10 m in mean/dominating tree height). Treatments were control, pre-commercial thinning (PCT), conventional selective thinning and BCT (high and low thinning). Following the first biomass thinning, BCT regimes and selective thinning methods resulted in similar stand structures based on the number of possible future crop trees (>80 mm in diameter at breast height). However, BCT maintained a higher diversity of tree sizes as well as more stems per hectare, including deciduous species, than the selective thinning approaches. The stands after BCT should have more vertical complexity, especially when compared to pre-commercial thinning. The structural heterogeneity resulting from BCT may also increase stand biodiversity and ecosystem service values.
Understanding the characteristics of unutilized biomass resources, such as small-diameter trees from biomass-dense thinning forests (BDTF) (non-commercially-thinned forests), can provide important information for developing a bio-based economy. The aim of this study was to describe the areal distribution, characteristics (biomass of growing stock, tree height, etc.) and harvesting potential of BDTF in Sweden. A national forest inventory plot dataset was imported into a geographical information system and plots containing BDTF were selected by applying increasingly stringent constraints. Results show that, depending on the constraints applied, BDTF covers 9–44% (2.1–9.8 M ha) of the productive forest land area, and contains 7–34% of the total growing stock (119–564 M OD t), with an average biomass density of 57 OD t ha–1. Of the total BDTF area, 65% is located in northern Sweden and 2% corresponds to set-aside farmlands. Comparisons with a study from 2008 indicate that BDTF area has increased by at least 4% (about 102 000 ha), in line with general trends for Sweden and Europe. Analyses revealed that the technical harvesting potential of delimbed stemwood (over bark, including tops) from BDTF ranges from 3.0 to 6.1 M OD t yr–1 (7.5 to 15.1 M m3 yr–1), while the potential of whole-tree harvesting ranges from 4.3 to 8.7 M OD t yr–1 (10.2 to 20.6 M m3 yr–1) depending on the scenario considered. However, further technological developments of the harvest and supply systems are needed to utilize the full potential of BDTF.
Stump wood is a possible alternative to fossil fuel. Its harvesting, however, disturbs the ground and this has not yet been quantified at stump level. Such disturbance is likely to be dependent on stump size, type of soil and timing of stump harvesting. Therefore, we measured ground disturbance and root breakage diameter at two Norway spruce sites with sandy glacial till soil. The sites were harvested with a fork type head, 6 and 18 months after clear cutting. Measurements were made within 2 weeks of harvest. No difference was found between the two sites. The mean area of disturbed ground was 6.06 (std 3.14) m2 per stump and increased exponentially with stump size. A regression function modelling the relationship was constructed. Unexpectedly, many fine roots where extracted in the harvest. The arithmetic and basal area weighted mean root breakage diameter was 4.6 (std 2.2) and 29.5 (std 17.9) mm, respectively. There seems to be a limited increase in root breakage diameter with increased stump size. The small root breakage diameter is associated with reduced fuel quality and greater nutrient removal. It appears that much of the ground disturbance is associated with the creation of ruts rather than stump harvest per se. Stump harvesting disturbs a larger percentage of the area of a harvested site than mounding. Postponing stump harvest by one year did not decrease the ground disturbance or increase the root breakage diameter. To achieve less disturbance and larger root breakage diameter, probably new stump harvesting technology is required.