Current issue: 53(3)

Under compilation: 53(4)

Impact factor 1.683
5-year impact factor 1.950
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles containing the keyword 'image analysis'.

Category: Research article

article id 296, category Research article
Samuel Roturier, Sofia Bäcklund, Maria Sundén, Urban Bergsten. (2007). Influence of ground substrate on establishment of reindeer lichen after artificial dispersal. Silva Fennica vol. 41 no. 2 article id 296. https://doi.org/10.14214/sf.296
Methods to improve the recovery of reindeer lichen after soil disturbance or overgrazing are being sought for areas where reindeer are herded. The effects of four substrates – mineral soil, moss, twigs and pine bark – on the establishment of lichen fragments after total removal of the vegetation were thus studied in a middle-aged pine stand and a clear-cut, both located in a lichen-rich pine-heath. Cladina mitis fragments of two sizes were manually dispersed in 1 m2 quadrats and their movements from their respective dispersal points were registered after one year. The natural re-establishment of lichens in the quadrats was monitored over three years by using digital pictures. In the forest stand, no significant differences were detected in either the fragment movement or the lichen establishment between the different substrates, but the fragment size had positive effects on both parameters. In the clear-cut, the moss substrate was the most suitable not only for the artificially dispersed lichens to fasten to, but also for the natural settlement of lichens from the surrounding lichen mat. More lichen thalli fastened to the bark and twigs substrates than to the mineral soil, but the settlement of lichens from the surrounding was greater on bare mineral soil substrate. The results indicate that artificial dispersal of lichen thalli on an appropriate substrate could be a successful strategy for promoting lichen recovery.
  • Roturier, SLU, Vindeln Experimental Forests, Svartberget Fältstation, SE-922 91 Vindeln, Sweden ORCID ID:E-mail: samuel.roturier@esf.slu.se (email)
  • Bäcklund, ORCID ID:E-mail:
  • Sundén, ORCID ID:E-mail:
  • Bergsten, SLU, Dept of Forest Ecology, SE-901 83 Umeå, Sweden ORCID ID:E-mail:
article id 542, category Research article
Håkan Lindström. (2002). Intra-tree models of juvenile wood in Norway spruce as an input to simulation software. Silva Fennica vol. 36 no. 2 article id 542. https://doi.org/10.14214/sf.542
Juvenile wood found in the first 5–25 growth rings of a conifer has a structure and properties that differ from mature wood. Juvenile wood is therefore said to influence processing and the end-use of sawn products. Consequently, models describing the juvenile wood content, within and between trees, could be useful in improving the utilisation and value of wood as an industrial raw material. The objective of the present study was to develop juvenile wood models, based on Norway spruce trees, which could be used within a model system for conversion simulation studies. Nineteen stands of Norway spruce (Picea abies [L.] Karst.) were selected throughout Sweden. Based on DBH, two small, two medium, and two large diameter timber trees were taken from each stand. DBH varied between 180–470 mm, tree height between 17–34 m, and total age between 51–152 years. Each selected tree was cross-cut into logs; discs were prepared from the large end of each log and from the top end of the top log. Image analysis was used to determine growth ring development on sampled discs. Using tree and growth variables, the juvenile core radius and the logarithmic value of juvenile wood percentage were modelled. The two models had an R2Adj of 0.71 and 0.88 respectively.
  • Lindström, University of Canterbury, School of Forestry, Private Bag 4800, Christchurch, New Zealand ORCID ID:E-mail: lindstromhakan@netscape.net (email)
article id 622, category Research article
Håkan Lindström. (2000). Intra-tree models of basic density in Norway spruce as an input to simulation software. Silva Fennica vol. 34 no. 4 article id 622. https://doi.org/10.14214/sf.622
Basic density is said to influence aspects of conversion, properties, and end-use of forest products. Consequently, it is argued that accurate models of basic density variation, within and between trees, could be used to improve the utilisation of wood as an industrial raw material. The objective of the present study was to develop basic density models based on Norway spruce trees, that could be used within a model system for conversion simulation studies. Nineteen stands of Norway spruce (Picea abies (L.) Karst.) were selected throughout Sweden. Based on dbh, two small, two moderate, and two large timber trees were taken from each stand. Dbh varied between 180–470 mm, tree height between 17–34 m, and total age between 51–152 years. Each selected tree was cross-cut into logs; discs were prepared from the butt end of each log and from the top end of the top log. Computed tomography scanning and image analysis were used to determine basic density and growth ring development on sampled discs. Basic density development in 20-mm segments from pith outwards was modelled in models based on ring width, tree and growth condition data. The resulting models had an adjusted R2 of 0.37–0.51 and a RMSE of 37–41 kg/m3.
  • Lindström, University of Canterbury, School of Forestry, Private Bag 4800, Christchurch, New Zealand ORCID ID:E-mail: lindstromhakan@netscape.net (email)

Register
Click this link to register for Silva Fennica submission and tracking system.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles

Committee on Publication Ethics A Trusted Community-Governed Archive