Current issue: 53(3)

Under compilation: 53(4)

Impact factor 1.683
5-year impact factor 1.950
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles containing the keyword 'timber'.

Category: Research article

article id 10074, category Research article
Sebastian Kühle, Alfred Teischinger, Manfred Gronalt. (2019). Optimal location of laminated beech production plants within the solid hardwood supply network in Austria. Silva Fennica vol. 53 no. 3 article id 10074. https://doi.org/10.14214/sf.10074
Highlights: This paper provides data to the solid hardwood business and develops a mixed integer linear program model to design a laminated beech wood supply network; It covers the strategic decision where to locate a new production facility within the existing supply network with the lowest supply network cost; Sufficient sawn wood suppliers and potential facility locations are provided.

Due to changes in forest management in various European countries, hardwood forest areas and amounts will increase. Sustainable and individual utilization concepts have to be developed for the upcoming available resource. Studies conclude that there is low potential for hardwoods in the traditional appearance market thus the application areas have to be extended to new structural innovative products. This paper examines the extension to a future laminated beech wood supply network which would be a combination of already existing and new production facilities. For a better future use of hardwood raw materials it is necessary to consider the entire supply chain. This also better shows a total hardwood value chain. Therefore, this paper provides data to the solid hardwood business and develops a mixed integer linear programming to design a laminated beech wood supply network. The model is applied to Austria as the sample region. It covers the important strategic decisions where to locate a downstream facility within the existing production network with the lowest supply network cost. Fourteen scenarios are developed to examine various future network configurations. Results about optimal material flows and used sawmills as well as downstream production facilities are presented in form of material and financial performances. Two optimal laminated beech production locations are determined by the calculated scenarios results, and the impact of a new sawmill is analyzed which is focused on beech.

  • Kühle, BOKU - University of Natural Resources and Life Sciences, Vienna, Department of Material Science and Process Engineering, and Renewable Institute of Wood Technology Materials, Konrad-Lorenz-Straße 24, 3430 Tulln, Austria ORCID ID:E-mail: skuehle@boku.ac.at (email)
  • Teischinger, BOKU - University of Natural Resources and Life Sciences, Vienna, Department of Material Science and Process Engineering, and Renewable Institute of Wood Technology Materials, Konrad-Lorenz-Straße 24, 3430 Tulln, Austria ORCID ID:E-mail: alfred.teischinger@boku.ac.at
  • Gronalt, BOKU - University of Natural Resources and Life Sciences, Vienna, Department of Economics and Social Sciences, Institute of Production and Logistics, Feistmantelstraße 4, 1180 Vienna, Austria ORCID ID:E-mail: manfred.gronalt@boku.ac.at
article id 1313, category Research article
Jonathan Sheppard, Christopher Morhart, Heinrich Spiecker. (2016). Bark surface temperature measurements on the boles of wild cherry (Prunus avium) grown within an agroforestry system. Silva Fennica vol. 50 no. 3 article id 1313. https://doi.org/10.14214/sf.1313
Highlights: Widely spaced trees within agroforestry systems are at risk of sun induced damages; Bark surface temperature on the south western bole face reached nearly 50 °C in summer and experienced a maximum range of 38 °C within a 24 hour period in spring; Maximum and minimum daily bark surface temperatures are modelled using climatic and solar position data; The application of white paint to stems reduces the bark surface temperature.

Growing Prunus avium L. within an agroforestry system (AFS) may result in sun damage to cambial tissues on sun-exposed bole faces. There are two periods of risk of damage caused by insolation to exposed tree boles, the summer, when cambial temperatures become too high, or during winter, when the frozen dormant cambium tissue thaws and then rapidly re-freezes, a phenomenon commonly referred to as sunscald or southwest disease. Damage on the south western bole face was observed on a number of P. avium within an AFS. Five trees were sampled to assess the period in time that damage occurred. To retrospectively investigate such damage, bark surface temperature data were collected over a two year period for a further five P. avium and analysed. It was shown that bark surface temperature on the south western bole face reached nearly 50 °C during summer and experienced a maximum range of 38 °C within a 24 hour period in spring. A specially formulated white paint was applied to two trees, thus, testing a method to reduce the risk of sun damage. Two models were constructed to predict maximum and minimum daily bark surface temperature using maximum, minimum and mean daily air temperature, daily sum of sunshine hours, cloud cover, wind speed, relative humidity, maximum solar elevation and height on the tree bole as predictor variables. The damage occurred during winter 2009/2010. The models were used to identify maximum and minimum bark surface temperatures during that winter enabling the identification of possible damage events.

  • Sheppard, Chair of Forest Growth and Dendroecology, Albert-Ludwigs-University Freiburg, Tennenbacher Straße 4, 79106 Freiburg, Germany ORCID ID: http://orcid.org/0000-0002-4959-7069 E-mail: jonathan.sheppard@iww.uni-freiburg.de (email)
  • Morhart, Chair of Forest Growth and Dendroecology, Albert-Ludwigs-University Freiburg, Tennenbacher Straße 4, 79106 Freiburg, Germany ORCID ID: http://orcid.org/0000-0003-1874-5011 E-mail: christopher.morhart@iww.uni-freiburg.de
  • Spiecker, Chair of Forest Growth and Dendroecology, Albert-Ludwigs-University Freiburg, Tennenbacher Straße 4, 79106 Freiburg, Germany ORCID ID:E-mail: instww@uni-freiburg.de
article id 1226, category Research article
Santiago Pereira, Antonio Prieto, Rafael Calama, Luis Diaz-Balteiro. (2015). Optimal management in Pinus pinea L. stands combining silvicultural schedules for timber and cone production. Silva Fennica vol. 49 no. 3 article id 1226. https://doi.org/10.14214/sf.1226
Highlights: Three management scenarios are proposed to integrate timber and pine nuts; Different silvicultural regimes for each output are addressed jointly; Goal programming is used in order to solve forest management models; In the mixed scenario, the area allocated to pine nuts should be notably greater.

This work aimed to tackle a timber harvest scheduling problem by simultaneously integrating into the analysis two forestry products derived from the same species: the timber and the pine nut. For this purpose, three management scenarios were proposed: two in which each of the productions is maximised separately, and a third mixed where, in each management unit, the product to which the silvicultural effort should be devoted is decided. After defining a set of objectives, and optimising the rotation length, a multi-criteria model based on goal programming was considered since no feasible solutions have been obtained when employing linear programming. The results in our case study show how the feasible solutions reached can be more attractive for the manager. Specifically, the area to be devoted to timber and cone/pine-nut production was computed in a scenario where the optimal silviculture (oriented towards timber or pine nuts) in each stand was selected, and it was concluded that the area allocated to pine nuts should be notably greater. This situation is the opposite of the current management.

  • Pereira, Technical University of Madrid, ETS Ingenieros de Montes, Ciudad Universitaria s/n, 28040 Madrid, Spain ORCID ID:E-mail: spereirasaez@gmail.com
  • Prieto, Technical University of Madrid, ETS Ingenieros de Montes, Ciudad Universitaria s/n, 28040 Madrid, Spain ORCID ID:E-mail: antonio.prieto@upm.es
  • Calama, Dpto. Selvicultura y Gestión Forestal, INIA-CIFOR, Ctra. A Coruña km 7.5, 28040 Madrid, Spain ORCID ID:E-mail: rcalama@inia.es
  • Diaz-Balteiro, Technical University of Madrid, ETS Ingenieros de Montes, Ciudad Universitaria s/n, 28040 Madrid, Spain ORCID ID:E-mail: luis.diaz.balteiro@upm.es (email)
article id 1159, category Research article
Grzegorz Szewczyk, Janusz Michał Sowa, Włodzimierz Grzebieniowski, Mariusz Kormanek, Dariusz Kulak, Arkadiusz Stańczykiewicz. (2014). Sequencing of harvester work during standard cuttings and in areas with windbreaks. Silva Fennica vol. 48 no. 4 article id 1159. https://doi.org/10.14214/sf.1159
Highlights: In standard cutting stands and thinning areas with windbreaks there occurred three-activity operational cycles. In mature stands with windbreaks the occurrence of stable sequences supplemented with five-activity cycles was noted. Consequently, the operational time in post-disaster thinning stands should be increased by 55% whereas in mature stands it should be 30% longer in comparison with standard stands.
The aim of the study was to characterize repetitive cycles of harvester operation. The study was conducted in thinning, mature and post-disaster pine stands. The sequences of the activities characteristic of harvester operation were described as time series. In order to detect the cyclic variable structure of the analysed time series, the methodology of the single spectrum Fourier analysis was applied. In standard stands, post-disaster late-thinning stands and mature stands, the existence of stable operational cycles with the length of three activities was discovered while in post-disaster mature stands additional five-activity operational phases were noted. Described in this way, the lengths of the operational cycles of harvesters working in post-disaster areas were higher by about 55% and 30% respectively, as compared to standard thinning and mature stands.
  • Szewczyk, University of Agriculture in Krakow, Faculty of Forestry, Institute of Forest Utilization and Forest Technology, Department of Forest and Wood Utilization, Al. 29-Listopada 46, 31-425 Krakow, Poland ORCID ID:E-mail: rlszewcz@cyf-kr.edu.pl (email)
  • Sowa, University of Agriculture in Krakow, Faculty of Forestry, Institute of Forest Utilization and Forest Technology, Department of Forest and Wood Utilization, Al. 29-Listopada 46, 31-425 Krakow, Poland ORCID ID:E-mail: rlsowa@cyf-kr.edu.pl
  • Grzebieniowski, University of Agriculture in Krakow, Faculty of Forestry, Institute of Forest Utilization and Forest Technology, Department of Forest and Wood Utilization, Al. 29-Listopada 46, 31-425 Krakow, Poland ORCID ID:E-mail: wrzoswj@interia.pl
  • Kormanek, University of Agriculture in Krakow, Faculty of Forestry, Institute of Forest Utilization and Forest Technology, Department of Forest Work Mechanisation, Al. 29-Listopada 46, 31-425 Krakow, Poland ORCID ID:E-mail: rlkorma@cyf-kr.edu.pl
  • Kulak, University of Agriculture in Krakow, Faculty of Forestry, Institute of Forest Utilization and Forest Technology, Department of Forest and Wood Utilization, Al. 29-Listopada 46, 31-425 Krakow, Poland ORCID ID:E-mail: rlkulak@cyf-kr.edu.pl
  • Stańczykiewicz, University of Agriculture in Krakow, Faculty of Forestry, Institute of Forest Utilization and Forest Technology, Department of Forest and Wood Utilization, Al. 29-Listopada 46, 31-425 Krakow, Poland ORCID ID:E-mail: rlstancz@cyf-kr.edu.pl
article id 1153, category Research article
Anu Akujärvi, Ville Hallikainen, Mikko Hyppönen, Eero Mattila, Kari Mikkola, Pasi Rautio. (2014). Effects of reindeer grazing and forestry on ground lichens in Finnish Lapland. Silva Fennica vol. 48 no. 3 article id 1153. https://doi.org/10.14214/sf.1153
Highlights: Both reindeer grazing and forestry affect the cover and biomass of reindeer lichens; Reindeer grazing has bigger impact than forestry; The lichen cover was about five-fold and the biomass about fifteen-fold in the ungrazed (fenced) sites than in the grazed ones; The decrease of not only the biomass, but also the cover of lichens, is alarming.
Reindeer husbandry and forestry are practiced in the same areas in northern Fennoscandia. Reindeer pastures have largely deteriorated. We aimed to quantify the separate and combined effects of reindeer grazing and forestry on the amount of ground lichens. To do this, we mapped and inventoried all larger enclosures (49) in Finnish Lapland where forest management practices were similar in both sides of the fence. The average time since fencing was 43 years. We recorded the cover and estimated dry biomass of ground lichens, as well as parameters describing forest stand characteristics. The effect of reindeer grazing on both the cover and estimated dry biomass of lichens was clear: in the ungrazed (fenced) sites, the lichen cover (35.8%) was on average 5.3-fold and the dry biomass (1929 kg ha–1) 14.8-fold compared with the corresponding estimates in the grazed sites (6.8% and 130 kg ha–1). The effect of forestry on lichens was smaller. In the grazed stands the cover and biomass of lichens were higher in the mature stands compared to the younger stand development classes, whereas in the ungrazed stands there were no significant differences between the development classes. Both reindeer grazing and forestry affect the cover and biomass of ground lichens. The influence of reindeer grazing is, however, much heavier than that of forestry. The decrease of not only the biomass, but also the lichen cover, is alarming. The decrease of lichen cover may hinder the recovery of reindeer pastures, which in the long run endangers the sustainability of reindeer husbandry.
  • Akujärvi, Finnish Environment Institute, Helsinki, Finland ORCID ID:E-mail: anu.akujarvi@ymparisto.fi
  • Hallikainen, Finnish Forest Research Institute, Northern Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: ville.hallikainen@metla.fi
  • Hyppönen, Finnish Forest Research Institute, Northern Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: mikko.hypponen@metla.fi (email)
  • Mattila, Finnish Forest Research Institute, Northern Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: eero.mattila@metla.fi
  • Mikkola, Finnish Forest Research Institute, Northern Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: kari.mikkola@metla.fi
  • Rautio, Finnish Forest Research Institute, Northern Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: pasi.rautio@metla.fi
article id 1054, category Research article
Karin Kolis, Juhana Hiironen, Esa Ärölä, Arvo Vitikainen. (2014). Effects of sale-specific factors on stumpage prices in Finland. Silva Fennica vol. 48 no. 3 article id 1054. https://doi.org/10.14214/sf.1054
Highlights: Data on 4824 individual sales were used to estimate which factors affect stumpage prices; The time of sale, seasonal harvest restrictions, the location and the assortment affected prices; Larger total volumes and shorter forest haulage distances raised unit prices; A higher percentage of the assortment and percentage of sawlogs within the sale corresponded to higher prices.
Buyers of standing timber take not only the market situation but also the harvest costs into consideration when making purchase offers. In Finland, 85% of all timber is sold as standing timber, but there is little information for forest owners and third parties regarding how differences in harvest costs are reflected in the stumpage prices. This article analyses the relationship between sale-specific factors and stumpage prices in Finland. Data on 4824 standing timber sales between 2008 and 2012 were gathered from five local Forest Management Associations. Regression analyses were run on the stumpage prices (euros m–3) paid for sawlogs and pulpwood. Seasonal harvest restrictions, the volume of the sale and the timber assortment influenced stumpage prices, as did the presence of forest damages. Prices also differed over time and between locations. Furthermore, the forest haulage distance was statistically significant for pulpwood. The results suggest that the size of the individual sales and the composition of assortments affect the income owners earn from their forest. The results can be used to estimate stumpage prices and the monetary impacts on forest owners of procedures such as forest road network planning and land consolidation, as well as for valuation of forests.
  • Kolis, Aalto University, Department of Real Estate, Planning and Geoinformatics, P.O. Box 12200, FI-00076 Aalto, Finland ORCID ID:E-mail: karin.kolis@aalto.fi (email)
  • Hiironen, Aalto University, Department of Real Estate, Planning and Geoinformatics, P.O. Box 12200, FI-00076 Aalto, Finland ORCID ID:E-mail: juhana.hiironen@aalto.fi
  • Ärölä, National Land Survey of Finland, Production Support Services, P.O. Box 84, FI-00521 Helsinki, Finland ORCID ID:E-mail: esa.arola@nls.fi
  • Vitikainen, Aalto University, Department of Real Estate, Planning and Geoinformatics, P.O. Box 12200, FI-00076 Aalto, Finland ORCID ID:E-mail: arvo.vitikainen@aalto.fi
article id 1054, category Research article
Karin Kolis, Juhana Hiironen, Esa Ärölä, Arvo Vitikainen. (2014). Effects of sale-specific factors on stumpage prices in Finland. Silva Fennica vol. 48 no. 3 article id 1054. https://doi.org/10.14214/sf.1054
Highlights: Data on 4824 individual sales were used to estimate which factors affect stumpage prices; The time of sale, seasonal harvest restrictions, the location and the assortment affected prices; Larger total volumes and shorter forest haulage distances raised unit prices; A higher percentage of the assortment and percentage of sawlogs within the sale corresponded to higher prices.
Buyers of standing timber take not only the market situation but also the harvest costs into consideration when making purchase offers. In Finland, 85% of all timber is sold as standing timber, but there is little information for forest owners and third parties regarding how differences in harvest costs are reflected in the stumpage prices. This article analyses the relationship between sale-specific factors and stumpage prices in Finland. Data on 4824 standing timber sales between 2008 and 2012 were gathered from five local Forest Management Associations. Regression analyses were run on the stumpage prices (euros m–3) paid for sawlogs and pulpwood. Seasonal harvest restrictions, the volume of the sale and the timber assortment influenced stumpage prices, as did the presence of forest damages. Prices also differed over time and between locations. Furthermore, the forest haulage distance was statistically significant for pulpwood. The results suggest that the size of the individual sales and the composition of assortments affect the income owners earn from their forest. The results can be used to estimate stumpage prices and the monetary impacts on forest owners of procedures such as forest road network planning and land consolidation, as well as for valuation of forests.
  • Kolis, Aalto University, Department of Real Estate, Planning and Geoinformatics, P.O. Box 12200, FI-00076 Aalto, Finland ORCID ID:E-mail: karin.kolis@aalto.fi (email)
  • Hiironen, Aalto University, Department of Real Estate, Planning and Geoinformatics, P.O. Box 12200, FI-00076 Aalto, Finland ORCID ID:E-mail: juhana.hiironen@aalto.fi
  • Ärölä, National Land Survey of Finland, Production Support Services, P.O. Box 84, FI-00521 Helsinki, Finland ORCID ID:E-mail: esa.arola@nls.fi
  • Vitikainen, Aalto University, Department of Real Estate, Planning and Geoinformatics, P.O. Box 12200, FI-00076 Aalto, Finland ORCID ID:E-mail: arvo.vitikainen@aalto.fi
article id 908, category Research article
Sattar Ezzati, Akbar Najafi, M. A. Rab, Eric K. Zenner. (2012). Recovery of soil bulk density, porosity and rutting from ground skidding over a 20-year period after timber harvesting in Iran. Silva Fennica vol. 46 no. 4 article id 908. https://doi.org/10.14214/sf.908
Ground-based skidding can have detrimental effects on soil properties trough soil profile disturbance and compaction that can persist for decades. We investigated the recovery of physical properties of disturbed brown soils on four abandoned downhill skid trails in a deciduous mountain forest in northern Iran. The most recent skidding operations had taken place 1–5 yrs, 6–10 yrs, 11–15 yrs, and 16–20 yrs ago, providing a 20-year chronosequence with four 5-year recovery periods. For each recovery period, mean values for soil bulk density (BD), total porosity (TP), macroporosity (MP), soil moisture content (SM), and rut depth (RD) were assessed for three levels of traffic intensity (Primary (PS), Secondary (SS) and Tertiary (TS) skid trails) and two levels of slope gradients (Gentle (G) and Steep (S)) and compared to those in undisturbed (control) areas. Over the 20-year recovery period, PS trails on gentle slopes exhibited mean values that were 35–42% (BD), 3–7% (SM), and 13–19 cm (RD) greater and 18–24% (TP) and 19–28% (MP) lower compared to undisturbed areas; on steep PS trails, values were 40–46% (BD), 2–13% (SM), and 13–21 cm (RD) greater and 23–27% (TP) and 28–35% (MP) lower, respectively. While RD and SM recovered, 20 years was not long enough for the other physical soil properties, particularly on steep slopes. To minimize soil disturbance, skidding should be confined to areas with gentle slopes and alternative harvesting methods such as cable yarding should be used where slope gradients exceed 20%.
  • Ezzati, Department of Forestry and Forest Engineering, Tarbiat Modares University, P.O. Box 64414-356, Iran ORCID ID:E-mail:
  • Najafi, Department of Forestry and Forest Engineering, Tarbiat Modares University, P. Box 64414-356, Iran ORCID ID:E-mail: a.najafi@modares.ac.ir (email)
  • Rab, Soil Physics Future Farming Systems Research Division, Department of Primary Industries, Victoria, Australia ORCID ID:E-mail:
  • Zenner, Department of Ecosystem Science and Management, Pennsylvania State University, University Park, PA, USA ORCID ID:E-mail: eric.zenner@psu.edu
article id 126, category Research article
Anders Roos, Lotta Woxblom, Denise McCluskey. (2010). The influence of architects and structural engineers on timber in construction – perceptions and roles. Silva Fennica vol. 44 no. 5 article id 126. https://doi.org/10.14214/sf.126
This study considers structural engineers’ and architects’ perceptions of structural timber in multi-story construction contexts. Qualitative approaches – interviews and focus groups – were used to investigate attitudes, perceived norms, and perceived factors that hamper or facilitate the prescription of wood use in construction. Wood was perceived as an appropriate building material. Architects’, and even more so engineers’, perceptions of negative aspects of wood focused on decay, instability and sound transmission. Although wood-based construction was seen as a required professional skill, it was not expected to improve one’s professional status. Positive aspects of wood in construction included its strength, environmental friendliness, simple handling and appropriateness for use in conjunction with industrial methods, whereas knowledge gaps and weak support from the wood industry have reduced the use of wood among structural engineers and architects. Both professions perceived their influence on material selection to be weak. They sensed that most of the influence over material selection rested with developers and contractors. The paper contains suggestions on how to make these two professions more influential advocates for wood in construction.
  • Roos, Swedish University of Agricultural Sciences, Department of Forest Products, P.O. Box 7008, SE-750 07 Uppsala, Sweden ORCID ID:E-mail: anders.roos@sprod.slu.se (email)
  • Woxblom, Swedish University of Agricultural Sciences, Department of Forest Products, P.O. Box 7008, SE-750 07 Uppsala, Sweden ORCID ID:E-mail:
  • McCluskey, Swedish University of Agricultural Sciences, Department of Forest Products, P.O. Box 7008, SE-750 07 Uppsala, Sweden ORCID ID:E-mail:
article id 126, category Research article
Anders Roos, Lotta Woxblom, Denise McCluskey. (2010). The influence of architects and structural engineers on timber in construction – perceptions and roles. Silva Fennica vol. 44 no. 5 article id 126. https://doi.org/10.14214/sf.126
This study considers structural engineers’ and architects’ perceptions of structural timber in multi-story construction contexts. Qualitative approaches – interviews and focus groups – were used to investigate attitudes, perceived norms, and perceived factors that hamper or facilitate the prescription of wood use in construction. Wood was perceived as an appropriate building material. Architects’, and even more so engineers’, perceptions of negative aspects of wood focused on decay, instability and sound transmission. Although wood-based construction was seen as a required professional skill, it was not expected to improve one’s professional status. Positive aspects of wood in construction included its strength, environmental friendliness, simple handling and appropriateness for use in conjunction with industrial methods, whereas knowledge gaps and weak support from the wood industry have reduced the use of wood among structural engineers and architects. Both professions perceived their influence on material selection to be weak. They sensed that most of the influence over material selection rested with developers and contractors. The paper contains suggestions on how to make these two professions more influential advocates for wood in construction.
  • Roos, Swedish University of Agricultural Sciences, Department of Forest Products, P.O. Box 7008, SE-750 07 Uppsala, Sweden ORCID ID:E-mail: anders.roos@sprod.slu.se (email)
  • Woxblom, Swedish University of Agricultural Sciences, Department of Forest Products, P.O. Box 7008, SE-750 07 Uppsala, Sweden ORCID ID:E-mail:
  • McCluskey, Swedish University of Agricultural Sciences, Department of Forest Products, P.O. Box 7008, SE-750 07 Uppsala, Sweden ORCID ID:E-mail:
article id 154, category Research article
Henrik R. Hallingbäck, Gunnar Jansson, Björn Hannrup, Anders Fries. (2010). Which annual rings to assess grain angles in breeding of Scots pine for improved shape stability of sawn timber? Silva Fennica vol. 44 no. 2 article id 154. https://doi.org/10.14214/sf.154
The shape stability properties of sawn timber could be improved by breeding or grading Scots pine (Pinus sylvestris L.) for reduced grain angles. Currently, only grain angle assessments performed in single annual rings can be considered feasible in forest breeding programmes. The relevance of such methods in assessing shape stability traits was evaluated by taking grain angle measurements beneath the bark in a 36-year-old Scots pine progeny trial. Several grain angle measurements from stem discs were also taken from a sample of 162 trees. Phenotypic correlations were estimated between grain angle and the bow, crook and twist developed in 316 sawn and dried boards. All single annual ring assessments, including measurements taken directly under the bark, were significantly correlated with twist. The highest correlations (0.60–0.70) were observed in annual rings numbered 8–20 and at distances of 30–70 mm from the pith, indicating those parts of logs where grain angles have the largest impact on twist. These results suggests, that grain angles measured beneath the bark are relevant to the twist of sawn small timber, and that any single annual ring could be chosen for the assessment, provided that the tree diameter is within the 60–140 mm range. No appreciable correlations were observed between grain angles and either crook or bow.
  • Hallingbäck, Dept of Plant Biology and Forest Genetics, Swedish University of Agricultural Sciences, Uppsala, Sweden ORCID ID:E-mail: henrik.hallingback@vbsg.slu.se (email)
  • Jansson, The Forestry Research Institute of Sweden, Uppsala, Sweden ORCID ID:E-mail:
  • Hannrup, The Forestry Research Institute of Sweden, Uppsala, Sweden ORCID ID:E-mail:
  • Fries, Dept of Forest Genetics and Plant Physiology, Swedish University of Agricultural Sciences, Umeå, Sweden ORCID ID:E-mail:
article id 165, category Research article
Yrjö Nuutinen, Kari Väätäinen, Antti Asikainen, Robert Prinz, Jaakko Heinonen. (2010). Operational efficiency and damage to sawlogs by feed rollers of the harvester head. Silva Fennica vol. 44 no. 1 article id 165. https://doi.org/10.14214/sf.165
In mechanical cutting, deep damage caused by feed rollers can reduce the yield of good quality timber for the sawmill and plywood industries. Additionally the feeding and energy efficiency of feed rollers are important for the profitability of harvester cutting. The objectives of this study were to compare the damages to sawlogs, as well as the time and fuel consumption of stem feeding with six different steel feed rollers during the processing of stems using a single grip harvester. This study tested two rollers with big spikes, two rollers with small spikes, one roller with studs in v-angle and one roller with adaptable steel plates in the ring of the roller. A highly detailed, and accurate processing and fuel consumption projection was recorded using the harvester’s automated data collector on a log and stem level. The roller adaptable plate averaged, for unbarked sawlogs, the lowest damages of 3.7 mm. While the damages of the roller with big spikes were the deepest with an average of 7.8 mm. For medium stems, volume of 0.35 m3, the range of differences between the maximum and minimum effective feeding time per roller was 6–19%, which would increase the effective time consumption of cutting by 1–3%. Corresponding differences in fuel consumption during total stem processing were in the range of 7–15%. According to this study it can be concluded that the traditional rollers with spikes were most effective in processing and fuel consumption, but at the same time they caused the deepest damages to the sawlogs. The roller type with adaptable steel plates was the most effective for small stems, additionally it also caused the least damage to the sawlogs.
  • Nuutinen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland ORCID ID:E-mail: yrjo.nuutinen@metla.fi (email)
  • Väätäinen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Asikainen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Prinz, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Heinonen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland ORCID ID:E-mail:
article id 177, category Research article
Tuomo Nurminen, Heikki Korpunen, Jori Uusitalo. (2009). Applying the activity-based costing to cut-to-length timber harvesting and trucking. Silva Fennica vol. 43 no. 5 article id 177. https://doi.org/10.14214/sf.177
The supply chain of the forest industry has increasingly been adjusted to the customer’s needs for precision and quality. This has changed the operative environment both in the forest and on the roads. As the total removal of timber is increasingly divided into more log assortments, the lot size of each assortment decreases and the time consumed in sorting the logs increases. In this respect, the extra assortments have made harvesting work more difficult and affected the productivity of both cutting and forest transport; this has thus increased the harvesting costs. An activity-based cost (ABC) management system is introduced for timber harvesting and long-distance transport, based on the cut-to-length (CTL) method, in which the logistic costs are assigned to timber assortments and lots. Supplying timber is divided into three main processes: cutting, forest transport, and long-distance transportation. An ABC system was formulated separately for each of these main operations. Costs were traced to individual stands and to timber assortment lots from a stand. The cost object of the system is thus a lot of timber that makes up one assortment that has been cut, forwarded, and transported from the forest to the mill. Application of the ABC principle to timber harvesting and trucking was found to be relatively easy. The method developed gives estimates that are realistic to actual figures paid to contractors. The foremost use for this type of costing method should be as a tool to calculate the efficiency of an individual activity or of the whole logistic system.
  • Nurminen, Metsätoimisto Tuomo Nurminen, Joensuuntie 5 B 8, FI-41800 Korpilahti, Finland ORCID ID:E-mail:
  • Korpunen, Finnish Forest Research Institute, Parkano Research Unit, Kaironiementie 54, FI-39700 Parkano, Finland ORCID ID:E-mail:
  • Uusitalo, Finnish Forest Research Institute, Parkano Research Unit, Kaironiementie 54, FI-39700 Parkano, Finland ORCID ID:E-mail:
article id 203, category Research article
Matti Maltamo, Jussi Peuhkurinen, Jukka Malinen, Jari Vauhkonen, Petteri Packalén, Timo Tokola. (2009). Predicting tree attributes and quality characteristics of Scots pine using airborne laser scanning data. Silva Fennica vol. 43 no. 3 article id 203. https://doi.org/10.14214/sf.203
The development of airborne laser scanning (ALS) during last ten years has provided new possibilities for accurate description of the living tree stock. The forest inventory applications of ALS data include both tree and area-based plot level approaches. The main goal of such applications has usually been to estimate accurate information on timber quantities. Prediction of timber quality has not been focused to the same extent. Thus, in this study we consider here the prediction of both basic tree attributes (tree diameter, height and volume) and characteristics describing tree quality more closely (crown height, height of the lowest dead branch and sawlog proportion of tree volume) by means of high resolution ALS data. The tree species considered is Scots pine (Pinus sylvestris), and the field data originate from 14 sample plots located in the Koli National Park in North Karelia, eastern Finland. The material comprises 133 trees, and size and quality variables of these trees were modeled using a large number of potential independent variables calculated from the ALS data. These variables included both individual tree recognition and area-based characteristics. Models for the dependent tree characteristics to be considered were then constructed using either the non-parametric k-MSN method or a parametric set of models constructed simultaneously by the Seemingly Unrelated Regression (SUR) approach. The results indicate that the k-MSN method can provide more accurate tree-level estimates than SUR models. The k-MSN estimates were in fact highly accurate in general, the RMSE being less than 10% except in the case of tree volume and height of the lowest dead branch.
  • Maltamo, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland ORCID ID:E-mail: matti.maltamo@joensuu.fi (email)
  • Peuhkurinen, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Malinen, Finnish Forest Research Institute, Joensuu Research Unit, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Vauhkonen, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Packalén, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Tokola, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland ORCID ID:E-mail:
article id 195, category Research article
John R. Moore, Andrew J. Lyon, Gregory J. Searles, Leena E. Vihermaa. (2009). The effects of site and stand factors on the tree and wood quality of Sitka spruce growing in the United Kingdom. Silva Fennica vol. 43 no. 3 article id 195. https://doi.org/10.14214/sf.195
The extent and sources of variation in the wood quality of Sitka spruce (Picea sitchensis (Bong.) Carr.) were quantified using data collected from 64 stands in northern Britain. These stands were selected on the basis of elevation, latitude, longitude, yield class, initial spacing and the presence or absence of thinning. Dynamic modulus of elasticity (MOE) was calculated from measurements of stress wave velocity made on standing trees and qualitative descriptions were made of stem form. Dynamic MOE of individual trees ranged from 3.81 kN/mm2 up to 12.29 kN/mm2, with a mean of 7.71 kN/mm2. Approximately 55 percent of the variation in dynamic MOE was due to differences between individual trees within a site, while 35 percent was due to differences between sites. The remaining 10 percent was due to differences between the measurements made on opposite sides of each tree. Variation in dynamic MOE at the site level was significantly influenced by yield class, elevation as well as by a number of the interactions between these factors and latitude, longitude and initial spacing. A multiple regression model incorporating these variables was able to explain 45 percent of the variation in dynamic MOE. Ramicorn branches were the most commonly recorded defect (37.2% of all live trees), followed by stem scarring and basal sweep (6.9% and 6.3%, respectively). Dynamic MOE was not influenced by stem straightness (p = 0.10) which indicates the utility of stress wave velocity measurements for segregating Sitka spruce stands based on potential grade recovery.
  • Moore, Centre for Timber Engineering, Napier University, 10 Colinton Road, Edinburgh EH10 5DT, United Kingdom ORCID ID:E-mail: j.moore@napier.ac.uk (email)
  • Lyon, Centre for Timber Engineering, Napier University, 10 Colinton Road, Edinburgh EH10 5DT, United Kingdom ORCID ID:E-mail:
  • Searles, Centre for Timber Engineering, Napier University, 10 Colinton Road, Edinburgh EH10 5DT, United Kingdom ORCID ID:E-mail:
  • Vihermaa, Department of Analytical and Environmental Chemistry, University of Glasgow, Glasgow, UK ORCID ID:E-mail:
article id 206, category Research article
Qiaoying Zhang, Yunchun Zhang, Shaolin Peng, Eshetu Yirdaw, Ning Wu. (2009). Spatial structure of alpine trees in Mountain Baima Xueshan on the southeast Tibetan Plateau. Silva Fennica vol. 43 no. 2 article id 206. https://doi.org/10.14214/sf.206
Most of the trees at treeline on the Tibetan Plateau are endemic to the Plateau. Yet little is known about these species. The study focused on the population structure, spatial patterns and associations of the treeline species Abies forestii var. georgei and Juniperus saltuaria at treeline and timberline in Mountain Baima Xueshan on the southeast Tibetan Plateau. These species form monodominant communities on the north- and south-facing slopes, respectively. Stem density, DBH-distribution, distribution pattern of different tree size classes, and intraspecific spatial association between different tree size classes of both species were analyzed. Spatial structure varied between A. forestii var. georgei and J. saltuaria, and for the same species, the spatial structures were also different from timberline to treeline. Stem density, mean tree height and young individuals of A. forestii var. georgei were significantly higher than those of J. saltuaria. For the same species, they were different from timberline to treeline, i.e., stem density and mean tree height of both species became lower. Size classes of both species were mainly clustered either at treeline or at timberline but at different scales, and spatial patterns of young J. saltuaria were mainly dominated by random patterns. Clumps of trees created more favorable microenvironments in harsh environments at treeline and timberline. Most tree size classes showed positive intraspecific spatial associations, but positive associations between size classes of J. saltuaria were not as significant as those of A. forestii var. georgei. The south-facing slope was usually subjected to varying intensities of pastoralism. Livestock disturbance greatly changed the microhabitat and reduced the number of young individuals. The potential of trees to regenerate was greatly inhibited, while A. forestii var. georgei showed greater regeneration potential. Spatial structures of J. saltuaria were also modified by this kind of human impact.
  • Zhang, State Key Laboratory of Biocontrol, Sun Yat-Sen University, Guangzhou 510275, Guangdong Province, China; Chengdu Institute of Biology, Chinese Academy of Sciences, Chengdu 610041, Sichuan Province, China ORCID ID:E-mail: lsspsl@mail.sysu.edu.cn (email)
  • Zhang, Shandong Institute of Light Industry, Jinan 250353, Shandong Province, China ORCID ID:E-mail:
  • Peng, State Key Laboratory of Biocontrol, Sun Yat-Sen University, Guangzhou 510275, Guangdong Province, China ORCID ID:E-mail:
  • Yirdaw, Viikki Tropical Resources Institute (VITRI), P.O. Box 27, FI-00014 University of Helsinki, Finland ORCID ID:E-mail:
  • Wu, Chengdu Institute of Biology, Chinese Academy of Sciences, Chengdu 610041, Sichuan Province, China ORCID ID:E-mail:
article id 267, category Research article
Manfred Gronalt, Peter Rauch. (2008). Vendor managed inventory in wood processing industries – a case study. Silva Fennica vol. 42 no. 1 article id 267. https://doi.org/10.14214/sf.267
Solid structure timber (SST) is an important building material in the wood construction business, in which its production volume is largely related to that respective business. Due to the large variability in the demand and seasonal factors, SST producers’ inventories are likely to be simultaneously overstocked for one type of timber and out of stock of another. An inventory policy that ensures a high service level and relatively low stocks is required. In the present paper, we propose the vendor managed inventory (VMI) approach for controlling the stock of deals that are produced at a sawmill and delivered as raw material for SST-production. We evaluate two VMI implementations against the actual inventory management for three different market scenarios. Furthermore, we layout the necessities for reconfiguring the business processes, and subsequently set up an organisational framework within VMI, which is indeed applicable in this segment of the woodworking industry. In our application background, VMI as an inventory control system is able to reduce the overall raw material stock by more than 37% by simultaneously increasing the SST service level.
  • Gronalt, BOKU – University of Natural Resources and Applied Life Sciences, Feistmantelstr. 4, 1180 Vienna, Austria ORCID ID:E-mail:
  • Rauch, BOKU – University of Natural Resources and Applied Life Sciences, Feistmantelstr. 4, 1180 Vienna, Austria ORCID ID:E-mail: peter.rauch@boku.ac.at
article id 278, category Research article
Katri Luostarinen. (2007). The effect of annual ring orientation and drying method on deformations, casehardening and colour of silver birch (Betula pendula) boards. Silva Fennica vol. 41 no. 4 article id 278. https://doi.org/10.14214/sf.278
Deformations of timber, caused mainly by anisotropic shrinkage, can be partially directed by controlling annual ring orientation through different sawing patterns. Ring orientation also affects the movement of water from within the board to its surface, with rapidity of drying having implications for the wood colour. Here sawn silver birch (Betula pendula Roth) timber was classed into two groups according to ring orientation. Two drying methods were used. The final moisture content was lower and the colour lighter in dried boards with radial than with tangential flats, but deformations were larger in radial than in tangential boards. Both drying and ring orientation affected the final moisture content and moisture gradient of the boards. Very small differences in board sizes or shape had an effect on both colour and deformations. The results support the need for accurate sawing and for classing silver birch timber sawn into parquet billets according to ring orientation in order to optimise the drying quality.
  • Luostarinen, University of Joensuu, Faculty of Forest Sciences, P.O. Box 111, FI-80101 Joensuu, Finland ORCID ID:E-mail: katri.luostarinen@joensuu.fi (email)
article id 308, category Research article
Ville Hallikainen, Mikko Hyppönen, Juha Hyvönen, Juhani Niemelä. (2007). Establishment and height development of harvested and naturally regenerated Scots pine near the timberline in North-East Finnish Lapland. Silva Fennica vol. 41 no. 1 article id 308. https://doi.org/10.14214/sf.308
Researchers and professionals in practical forestry have faced problems concerning the regeneration success of Scots pine in natural regeneration near the timberline in North-East Lapland. The aim of the study was to analyze the seedling establishment and seedling height development of Scots pine in seed-tree stands in the area. The average number of living pine seedlings in the study stands was about 1000 ha–1, but there was considerable variation between the stands. The seedling density was modelled using a multinomial logistic regression with a random factor. Forest site type and the time since seed-tree cutting were the most significant explanatory variables in the model. The probability of reaching the acceptable seedling density was higher on dry site types than on the more fertile ones. The probability increased with the time elapsed since the regeneration activities. Effective temperature sum and the number of intermediate pines also positively affected the probability, but the presence of residual trees negatively. On northern and eastern slopes the probability was lower than on southern and western ones. Seedling height was modelled using a linear mixed model. The age of a dominant seedling was the most positively effective explanatory variable in the height development model. Other positively affecting significant predictors were time since seed-tree cutting, number of intermediate birches, and distance between a seedling and the nearest seed tree. Degree of paludification had a negative effect. The study suggests that the regeneration of Scots pine in North-East Lapland is a relatively slow process.
  • Hallikainen, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: ville.hallikainen@metla.fi (email)
  • Hyppönen, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: mikko.hypponen@metla.fi
  • Hyvönen, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail: juha.hyvonen@metla.fi
  • Niemelä, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland ORCID ID:E-mail:
article id 329, category Research article
Vesa Juntunen, Seppo Neuvonen. (2006). Natural regeneration of Scots pine and Norway spruce close to the timberline in northern Finland. Silva Fennica vol. 40 no. 3 article id 329. https://doi.org/10.14214/sf.329
Two different datasets were analyzed in order to clarify the factors that affect regeneration success of Scots pine (Pinus sylvestris) and Norway spruce (Picea abies) in the climatically extreme areas in northern Finland. First, pine seed maturity and the number of cones in the trees were investigated at five pairs of study sites during the period 1997–2003. Secondly, the rate of seedling establishment and seedling survival of Scots pine and Norway spruce were monitored and compared among three different timberline zones (forest zone, timberline, tree line) in 13 localities during the period 1983–1999. The first study showed that both cone production (bud formation) and seed maturity may be limiting factors for successful reproduction in the climatically marginal habitats. Seed maturity correlated well with the temperature sum of the summer, but variation in the number of cones had a periodic component rather than strictly following the temperature sum of the summer of bud formation. Monitoring surveys since 1983 showed that pine and spruce regenerated more or less regularly in all the zones during 1983–1999. However, seedling mortality of pines was much higher compared to spruce. In general, initially small sized seedlings showed higher mortality compared with larger ones. The results suggest that besides restrictions in reproduction, stand dynamics in the timberline habitats are strongly controlled by seedling mortality due to a variety of causes.
  • Juntunen, Finnish Forest Research Institute, Kolari Research Unit, Muoniontie 21, FI-95900 Kolari, Finland ORCID ID:E-mail: vesa.juntunen@metla.fi (email)
  • Neuvonen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland ORCID ID:E-mail:
article id 387, category Research article
Sanna Laukkanen, Teijo Palander, Jyrki Kangas, Annika Kangas. (2005). Evaluation of the multicriteria approval method for timber-harvesting group decision support. Silva Fennica vol. 39 no. 2 article id 387. https://doi.org/10.14214/sf.387
The decision support methods most often used in timber-harvesting planning are based on a single criterion. In this study, a voting-theory-based method called multicriteria approval (MA) is introduced to the group decision support of timber-harvesting. The use of voting methods alleviates the problems caused by the multitude of decision objectives involved in forestry decision-making and by the poor quality of information concerning both the preferences of decision-makers and the evaluation of decision alternatives with respect to the objectives often faced in practical timber-harvesting planning. In the case study, the tactical forest management plan of a forest holding jointly owned by three people was specified at the operative timber-harvesting level. The task was to find the best actual operative alternatives for the harvesting that had been proposed in the tactical plan. These timber-harvesting alternatives were combinations of treatment, timber-harvesting system and the timing of logging. Forest owners established multiple criteria under which the alternatives were evaluated. Two versions of MA were tested, one of them based on individual decision analyses and other one based on a composite analysis. The first was markedly modified from the original MA, combining properties of MA and Borda count voting. The other was an original MA with the order of importance for criteria estimated either using Borda count or cumulative voting. The results of the tested MA versions produced were very similar to each other. MA was found to be a useful tool for the group decision support of timber-harvesting.
  • Laukkanen, University of Joensuu, Faculty of Forestry, P.O. Box 111, FI-80101 Joensuu, Finland ORCID ID:E-mail: sanna.laukkanen@joensuu.fi (email)
  • Palander, University of Joensuu, Faculty of Forestry, P.O. Box 111, FI-80101 Joensuu, Finland ORCID ID:E-mail:
  • Kangas, UPM-Kymmene Forest, P.O. Box 32, FI-37601 Valkeakoski, Finland ORCID ID:E-mail:
  • Kangas, University of Helsinki, Department of Forest Resource Management, P.O. Box 27, FI-00014 University of Helsinki, Finland ORCID ID:E-mail:
article id 436, category Research article
Martti Varmola, Hannu Salminen, Mauri Timonen. (2004). Thinning response and growth trends of seeded Scots pine stands at the arctic timberline. Silva Fennica vol. 38 no. 1 article id 436. https://doi.org/10.14214/sf.436
Growth patterns and reactions of Scots pine (Pinus sylvestris L.) to thinning in extremely harsh climatic conditions were studied in two seeded Scots pine stands located on the arctic timberline. Coniferous trees usually do not form closed stands at the timberline, but occur only in scattered tree groups. The trial was established in two stands in 1985–1986 when the trees were at an age of 47 and 56 years and an average dominant height of 6.0–6.9 m. The trial was remeasured in 1998. The thinning treatments reduced the stem number for five different levels; final density of 300, 550, 800, 1050, and 1300 stems ha–1 and unthinned. The experiment had a randomised block design with four replications in each stand. The increased growing space provided by thinning accelerated diameter growth after a delay of 2–3 years. The differences between the radial growth of the thinning treatments were very clear during the whole 13- to 14-year observation period. Annual increment of the mean diameter was regularly the higher, the larger the spacing. Dominant diameter was less influenced by treatments. There were no significant differences in dominant height between any of the treatments. Both basal area and volume were regularly the greater the higher the stem number was. Even a relatively light thinning had a distinct positive effect on tree growth, i.e. not carrying out thinning resulted in a production loss of merchantable wood. According to the results, seeded stands on the arctic timberline can grow surprisingly well in favourable conditions and reach a dominant height of 12–14 m in 100 years and a mean annual increment of 1.0–1.5 m3 ha–1 y–1 over a rotation period of 130–160 years. Based on increment figures and thinning reactions, a spacing of ca. 1000 stems ha–1 can be recommended.
  • Varmola, The Finnish Forest Research Institute, Rovaniemi Research Station, P.O.Box 16, FIN-96301 Rovaniemi, Finland ORCID ID:E-mail: martti.varmola@metla.fi (email)
  • Salminen, The Finnish Forest Research Institute, Rovaniemi Research Station, P.O.Box 16, FIN-96301 Rovaniemi, Finland ORCID ID:E-mail:
  • Timonen, The Finnish Forest Research Institute, Rovaniemi Research Station, P.O.Box 16, FIN-96301 Rovaniemi, Finland ORCID ID:E-mail:
article id 506, category Research article
Teijo Palander, Katja Turunen, Sanna Laukkanen. (2003). Attitude of Finnish timber buyers towards implementation of a forest computer visualisation. Silva Fennica vol. 37 no. 2 article id 506. https://doi.org/10.14214/sf.506
Timber buyers’ opinions as regards forest computer visualisation are studied. The results indicated that timber buyers are still rather conventional in their computer use since they mainly use only the information system of their own company. The majority of the buyers perceived computer visualisation to be slightly useful for their work, or they had no opinion concerning the usefulness of it. One third of the buyers considered computer visualisation to be a quality factor for timber trade, and the majority were willing to use it if a program is going to adopt by their company. In analysis, different personal characteristics were found for three timber buyer groups: qualified, neutral and reluctant. Qualified buyers were the largest one, about half of the buyers belonging to this group. The greatest barriers to adopting a positive attitude to computer visualisation turned out to be weak computer skills and a general lack of interest in computer use. On the other side, it was found that organisational factors did not influence the buyers’ computer skills or attitudes towards visualisation. The results of this study can be utilised by timber buying organisation in ensuring the successful adoption of a new computer system.
  • Palander, Faculty of Forestry, University of Joensuu, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail: teijo.palander@joensuu.fi (email)
  • Turunen, Faculty of Forestry, University of Joensuu, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail:
  • Laukkanen, Faculty of Forestry, University of Joensuu, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail:
article id 522, category Research article
Annika Kangas, Matti Maltamo. (2002). Anticipating the variance of predicted stand volume and timber assortments with respect to stand characteristics and field measurements. Silva Fennica vol. 36 no. 4 article id 522. https://doi.org/10.14214/sf.522
Several models and/or several variable combinations could be used to predict the diameter distribution of a stand. Typically, a fixed model and a fixed variable combination is used in all conditions. The calibration procedure, however, makes it possible to choose the measurement combination from among many possibilities, although the model used is fixed. In this study, the usefulness of utilizing additional stand characteristics for calibrating the predicted diameter distribution is examined. Nine measurement strategies were tested in predicting the total stand volume, sawlog volume and pulpwood volume. The observed errors of these variables under each strategy were modeled as a function of basal area, basal area median diameter and number of stems. The models were estimated in three steps. First, an Ordinary Least Squares (OLS) model was fitted to the observed errors. Then, a variance function was estimated using the OLS residuals. Finally, a weighted Seemingly Unrelated Regression (SUR) analysis was used to model the observed errors, using the estimated variance functions as weights. The estimated models can be used to anticipate the precision and accuracy of predicted volume characteristics for each stand with different variable combinations and, consequently, to choose the best measurement combination in different stands.
  • Kangas, University of Helsinki, Dept. of Forest Resources Management, P.O. Box 27, 00014 University of Helsinki, Finland ORCID ID:E-mail: annika.kangas@helsinki.fi (email)
  • Maltamo, University of Joensuu, Faculty of Forestry, P.O. Box 111, 80101 Joensuu, Finland ORCID ID:E-mail:
article id 589, category Research article
Pekka Mäkinen. (2001). Competitive strategies applied by Finnish timber carriers following deregulation. Silva Fennica vol. 35 no. 3 article id 589. https://doi.org/10.14214/sf.589
The present study examines the success of timber carriers and the factors involved in their success immediately following deregulation. In Finland in 1991 the timber trucking sector was deregulated. Means testing was changed to suitability testing, which meant that the Ministry of Transport and Communications, provincial authorities and the trucking association could no longer regulate the entry of new entrepreneurs to the sector. The present research material contains two successful enterprise groups. In the strategically more successful group, good results were obtained with a moderate labour input by the entrepreneurs. The strategic position of this group was considered to be successful because the operating hours of the trucks were fairly high but the work loads imposed on the entrepreneur remained reasonable. The profitability of these enterprises was so good that it was possible to use hired labour to drive the trucks. The work load of close to half of the unsuccessful entrepreneurs had been large or extremely large. In some cases, the obvious reason for failure was their inadequate transportation rates. Others had seemingly satisfactory haulage rates when compared to the average, but still their enterprises performed poorly. In these cases, the explanation lay in the inefficiency of operations or excessive debts, the latter caused, for example, by earlier operations. The results of this study do not support the view that a lot of hard work generally means success in entrepreneurship. The results support the view that both entrepreneurs’ work and management inputs have a significant impact on the success of the enterprise, and that high tariffs alone are not a guarantee of success.
  • Mäkinen, Finnish Forest Research Institute, Vantaa Research Centre, P.O. Box 18, FIN-01301 Vantaa ORCID ID:E-mail: pekka.makinen@metla.fi (email)
article id 584, category Research article
Ralph Alig, Darius Adams, John Mills, Richard Haynes, Peter Ince, Robert Moulton. (2001). Alternative projections of the impacts of private investment on southern forests: a comparison of two large-scale forest sector models of the United States. Silva Fennica vol. 35 no. 3 article id 584. https://doi.org/10.14214/sf.584
The TAMM/NAPAP/ATLAS/AREACHANGE (TNAA) system and the Forest and Agriculture Sector Optimization Model (FASOM) are two large-scale forestry sector modeling systems that have been employed to analyze the U.S. forest resource situation. The TNAA system of static, spatial equilibrium models has been applied to make 50-year projections of the U.S. forest sector for more than 20 years. Much of its input on forest management behavior and decisions about use of forestland derives from expert-based systems external to the TNAA system. FASOM, a spatial intertemporal optimization model, directly incorporates decisions on management investment and land use options relative to agricultural alternatives as endogenous model elements. The paper contrasts projections of private forest investment from the TNAA and FASOM models, focusing on the southern United States. Comparison of the TNAA base case and an investment-restricted scenario from FASOM, both of which reflect a continuation of recent behavioral tendencies by nonindustrial private owners, suggests that Southern private timberlands have considerable biological and economic potential for intensified forest management. Unrestricted FASOM projections confirm that added investment could lead to substantially larger timber harvest volumes and lower prices than those projected in the base/restricted cases. But even under the more intensive investment scenarios, naturally regenerated forests would cover three-quarters of the future private timberland base and hardwoods would continue to dominate the inventory structure.
  • Alig, USDA Forest Service, Forestry Sciences Lab, 3200 SW Jefferson Way, Corvallis, Oregon 97331, USA ORCID ID:E-mail: ralig@fs.fed.us (email)
  • Adams, College of Forestry, Oregon State University, Corvallis, Oregon 97331, USA ORCID ID:E-mail:
  • Mills, USDA Forest Service, Forestry Sciences Lab, 1221 SW Yamhill, Portland, Oregon 97205, USA ORCID ID:E-mail:
  • Haynes, USDA Forest Service, Forestry Sciences Lab, 1221 SW Yamhill, Portland, Oregon 97205, USA ORCID ID:E-mail:
  • Ince, USDA Forest Service, Forest Products Lab, Madison, Wisconsin 53705, USA ORCID ID:E-mail:
  • Moulton, USDA Forest Service (retired), Research Triangle Park, North Carolina 27709, USA ORCID ID:E-mail:
article id 583, category Research article
Hans Fredrik Hoen, Tron Eid, Petter Økseter. (2001). Timber production possibilities and capital yields from the Norwegian forest area. Silva Fennica vol. 35 no. 3 article id 583. https://doi.org/10.14214/sf.583
How intensely should a forest be grown? This is a fundamental question in the process of formulating policy guidelines for the management of a forest area, both at the individual property level as well as at the national level. The question is related to a number of factors; the objective(s) of the forest owner, the productivity of the forestland, the initial growing stock, the accessibility within the forest, assumptions regarding future prices and costs and the required real rate of return. This paper presents an applied analysis with the objective of mapping possible future paths for the growing stock on, and timber harvest from the productive forest area in Norway. The analysis is deterministic. The regeneration strategy is a key factor for the long run development of a forest and is thus given particular attention. The analysis is restricted to deal with timber production only and maximisation of the net present value of the forest area is used as the objective function. The required real rate of return is varied and used as the driving force to find the best (optimal) level of intensity in silvicultural management and thus optimal paths for harvesting and growing stocks.
  • Hoen, Agricultural University of Norway, Dept. of Forest Sciences, P.O. Box 5044, N-1432 Ås, Norway ORCID ID:E-mail: hans.hoen@isf.nlh.no (email)
  • Eid, Agricultural University of Norway, Dept. of Forest Sciences, P.O. Box 5044, N-1432 Ås, Norway ORCID ID:E-mail:
  • Økseter, Agricultural University of Norway, Dept. of Forest Sciences, P.O. Box 5044, N-1432 Ås, Norway ORCID ID:E-mail:
article id 621, category Research article
Jyrki Kangas, Pekka Leskinen, Timo Pukkala. (2000). Integrating timber price scenario modeling with tactical management planning of private forestry at forest holding level. Silva Fennica vol. 34 no. 4 article id 621. https://doi.org/10.14214/sf.621
In forest management planning, deterministic timber prices are typically assumed. However, real-life timber prices vary in the course of time, and also price peaks, i.e. exceptionally high timber prices, might occur. If land-owners can utilise the price variation by selling timber with the high prices, they are able to increase their net revenues correspondingly. In this study, an approach is presented to study the timber price variation and its significance in the optimization of forest management. The approach utilizes stochastic timber price scenario modelling, simulation of forest development, and optimization of forest management. The approach is presented and illustrated by means of a case study. It is shown how the degree of uncertainty due to variation in timber prices can be analyzed in tactical forest planning of private forestry, and how the potential benefits of adaptive timber-selling behaviour for a forest landowner can be computed by using the approach. The effects of stochastic timber prices on the choice of forest plan are studied at the forest holding level considering also the spacing and type of cuttings and the optimal cutting order. A forest plan prepared under the assumption of constant timber price very seldom results in optimal forest management. Through studying the effects of stochastic timber prices, forest landowners and other decision makers obtain valuable information about the significance of adaptive timber selling behaviour. The presented methodology can also be used in analysing the land-owners’ economic risks as a function of time-price structure.
  • Kangas, Finnish Forest Research Institute, Kannus Research Station, P.O. Box 44, FIN-69101 Kannus, Finland ORCID ID:E-mail: jyrki.kangas@metla.fi (email)
  • Leskinen, Finnish Forest Research Institute, Kannus Research Station, P.O. Box 44, FIN-69101 Kannus, Finland ORCID ID:E-mail:
  • Pukkala, University of Joensuu, Faculty of Forestry, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail:
article id 652, category Research article
M. J. Youngman, G. D. Kulasiri, I. M. Woodhead, G. D. Buchan. (1999). Use of combined constant rate and diffusion model to simulate kiln-drying of Pinus radiata timber. Silva Fennica vol. 33 no. 4 article id 652. https://doi.org/10.14214/sf.652
This paper presents the use of a combined constant drying-rate and diffusion model to simulate the drying of Pinus radiata timber under kiln-drying conditions. The constant drying-rate and diffusion coefficients of the model, which control the drying rate of individual pieces of timber, were determined from calibrating the model against the experimental drying curves obtained under the kiln-drying conditions. The experimental drying curves were obtained from the gravimetric measurements of the moisture content of timber during kiln drying. Statistical relationships were developed for the constant drying-rate and the diffusion coefficients of the model as functions of kiln temperature and the dry basis density of timber. To determine the effects of variability of timber, a simulation scheme was developed based on the model, the probability distribution of the density of timber, the equations for the constant drying-rate coefficient and the diffusion coefficient. The model and the associated simulation method provides a simple way to estimate the drying time of a stack of timber using parameters determined from experimental results for the specific timber kiln.
  • Youngman, Lincoln University, Appl. Management and Computing Division, P.O. Box 84, Canterbury, New Zealand ORCID ID:E-mail:
  • Kulasiri, Lincoln University, Appl. Management and Computing Division, P.O. Box 84, Canterbury, New Zealand ORCID ID:E-mail: kulasird@tui.lincoln.ac.nz (email)
  • Woodhead, Lincoln University, Appl. Management and Computing Division, P.O. Box 84, Canterbury, New Zealand ORCID ID:E-mail:
  • Buchan, Lincoln University, Appl. Management and Computing Division, P.O. Box 84, Canterbury, New Zealand ORCID ID:E-mail:
article id 667, category Research article
Timo Kärki. (1999). Predicting the value of grey alder (Alnus incana) logs based on external quality. Silva Fennica vol. 33 no. 1 article id 667. https://doi.org/10.14214/sf.667
The quality of grey alder logs (Alnus incana) was studied by sawing sample logs from two different forests in November 1995–February 1996. For grading of grey alder logs and sawn timber the proposed system of Keinänen and Tahvanainen (1995) plus the reject -grade was used. In general, grey alder logs have knots from the base to the top. All types of knots appear, and the length of the knot-free section is small at the base. In small-dimensioned logs there are fewer knots than in larger logs. Especially in large top logs, there were many more fresh knots than in other types of logs. Evidently, in different types of logs the different grades of sawn timber are located in comparable sections along the length. It also seems that the worse the grade class was, the longer was also the length of the class. The most common reasons for decreasing grade were dry knots and discoloration.
  • Kärki, University of Joensuu, Faculty of Forestry, P.O. BOX 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail: timo.karki@forest.joensuu.fi (email)
article id 698, category Research article
Kalle Kärhä, Sami Oinas. (1998). Satisfaction and company loyalty as expressed by non-industrial private forest owners towards timber procurement organizations in Finland. Silva Fennica vol. 32 no. 1 article id 698. https://doi.org/10.14214/sf.698
The satisfaction and company loyalty as expressed by non-industrial, private forest (NIPF) owners towards timber procurement organizations were clarified via a mail questionnaire. The results denoted that there is a positive correlation between the levels of forest owners’ expectations (EXP) and perceived performance (PERF). In addition, the lower EXP and the higher PERF were, the greater was the overall satisfaction index (SAT). About two thirds of forest owners were characterized by a negative SAT value or then they were dissatisfied with the performance of the procurement organization in their last timber-sales transaction. Furthermore, the results obtained indicated that the SAT index significantly influences the company loyalty expressed by NIPF owners – their willingness to give favourable reports of the company to the others, and their willingness to engage in future timber-sales transactions with the same company. Nonetheless, the SAT index did not affect the market share of a particular company, and this could be partly accounted for by the similar level of performance among the companies and the lack of competition in the timber trade. Finally, the results revealed several dimensions of timber procurement, and some seller segments to which companies could pay more attention to in order to be able to achieve better satisfaction levels and the loyalty of NIPF owners in the future. One approach to successfully addressing these challenges could be the adopting of a satisfaction decision support system (SatDSS).
  • Kärhä, Faculty of Forestry, University of Joensuu, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail: karha@forest.joensuu.fi (email)
  • Oinas, Faculty of Forestry, University of Joensuu, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail:
article id 698, category Research article
Kalle Kärhä, Sami Oinas. (1998). Satisfaction and company loyalty as expressed by non-industrial private forest owners towards timber procurement organizations in Finland. Silva Fennica vol. 32 no. 1 article id 698. https://doi.org/10.14214/sf.698
The satisfaction and company loyalty as expressed by non-industrial, private forest (NIPF) owners towards timber procurement organizations were clarified via a mail questionnaire. The results denoted that there is a positive correlation between the levels of forest owners’ expectations (EXP) and perceived performance (PERF). In addition, the lower EXP and the higher PERF were, the greater was the overall satisfaction index (SAT). About two thirds of forest owners were characterized by a negative SAT value or then they were dissatisfied with the performance of the procurement organization in their last timber-sales transaction. Furthermore, the results obtained indicated that the SAT index significantly influences the company loyalty expressed by NIPF owners – their willingness to give favourable reports of the company to the others, and their willingness to engage in future timber-sales transactions with the same company. Nonetheless, the SAT index did not affect the market share of a particular company, and this could be partly accounted for by the similar level of performance among the companies and the lack of competition in the timber trade. Finally, the results revealed several dimensions of timber procurement, and some seller segments to which companies could pay more attention to in order to be able to achieve better satisfaction levels and the loyalty of NIPF owners in the future. One approach to successfully addressing these challenges could be the adopting of a satisfaction decision support system (SatDSS).
  • Kärhä, Faculty of Forestry, University of Joensuu, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail: karha@forest.joensuu.fi (email)
  • Oinas, Faculty of Forestry, University of Joensuu, P.O. Box 111, FIN-80101 Joensuu, Finland ORCID ID:E-mail:

Category: Review article

article id 378, category Review article
Yaoqi Zhang, Daowei Zhang, John Schelhas. (2005). Small-scale non-industrial private forest ownership in the United States: rationale and implications for forest management. Silva Fennica vol. 39 no. 3 article id 378. https://doi.org/10.14214/sf.378
The transaction cost approach is used to explain why small non-industrial private forest (NIPF) ownerships are increasing in the U.S. We argue that the number of small NIPF owners have increased because: 1) a significant amount of forestland is no longer used economically if primarily for timber production, but rather for non-timber forest products and environmental services (particularly where population density is high), 2) when a person makes frequent use of non-timber products and services, owning forestland is more efficient for them because it saves the transaction costs involved in getting them from the market, 3) forestland parcelization takes place when non-timber value increases faster than timber value, and 4) marginal value for non-timber product is diminishing much faster than that for timber production. The paper also discusses implications of the parcelization of NIPF ownerships on forest management.
  • Zhang, School of Forestry & Wildlife Sciences, Auburn University, AL 36849-5418, USA ORCID ID:E-mail: yaoqi.zhang@auburn.edu (email)
  • Zhang, School of Forestry & Wildlife Sciences, Auburn University, AL 36849-5418, USA ORCID ID:E-mail:
  • Schelhas, Southern Research Station, USDA Forest Service, Tuskegee University, AL, USA ORCID ID:E-mail:

Category: Research note

article id 659, category Research note
Anneli Viherä-Aarnio, Pirkko Velling. (1999). Growth and stem quality of mature birches in a combined species and progeny trial. Silva Fennica vol. 33 no. 3 article id 659. https://doi.org/10.14214/sf.659
The growth and stem quality of silver birch (Betula pendula), downy birch (B. pubescens) and paper birch (B. papyrifera) were compared in a 32-year-old field trial in southern Finland. The material consisted of different unselected stand origins and progenies of phenotypically selected plus trees of silver and downy birch from southern Finland and differing stand origins of paper birch from the North-West Territories, Canada. Growth, yield and a number of stem quality traits, including taper, sweep, stem defects, heights of different crown limits and length of the veneer timber part of the stem were measured or observed. The native Finnish silver and downy birches were superior to paper birch in terms of both yield and stem quality, silver birch being the best. Progenies of silver birch plus trees were better than the stand origin, indicating that the former are able to reach high quality veneer log size in a shorter time than unselected material. The cultivation of paper birch can not be considered viable in Finland.
  • Viherä-Aarnio, The Finnish Forest Research Institute, Vantaa Research Centre, P.O. Box 18, FIN-01301 Vantaa, Finland ORCID ID:E-mail: anneli.vihera-aarnio@metla.fi (email)
  • Velling, The Finnish Forest Research Institute, Vantaa Research Centre, P.O. Box 18, FIN-01301 Vantaa, Finland ORCID ID:E-mail:

Category: Article

article id 7184, category Article
Bror-Anton Granvik. (1967). Havusahatavaran valmistus kenttäpyörösahalla : työtieteellinen tutkimus. Acta Forestalia Fennica vol. 84 no. 3 article id 7184. https://doi.org/10.14214/aff.7184
English title: The preparation of coniferous sawn goods using circular saws. A work study.

The objectives of the paper were to find out structure of the sawing time when using field circular saws, influence of the different factors on the sawing time and its structure, average sawing time per unit of raw material and sawn goods, and the fundamentals for the creation of an equitable system for the determination of the basis of payment in sawing work. The observations of the time study were made on both a single log and a work period basis. The material was collected using four saws of different brands.

The results showed that the season when the work was done, and top diameter of the logs to be sawn affected the constant times included in the total sawing time and the time used for sawing of center pieces. While the tree species did not affect the constant times, the grade of the logs of different tree species did have effect, especially in winter sawing. The factors affecting the different phases of the work are described in detail. The length of sawing time was longer in the winter than in the summer. The preparatory jobs in sawing required in average 82 cmin per log, and the time increased with increasing top diameter. The actual sawing is the most time-consuming part of the work, it took in average 132 cmin. 

The PDF includes a summary in English.

  • Granvik, ORCID ID:E-mail:
article id 7167, category Article
Veijo Heiskanen. (1966). Tutkimuksia rauduskoivikon karsimisen kannattavuudesta. Acta Forestalia Fennica vol. 81 no. 2 article id 7167. https://doi.org/10.14214/aff.7167
English title: Studies on the profitability of pruning of common birch (Betula pendula) stands.

The objective of the present investigation was to clarify the profitability of pruning silver birch (Betula verrucosa, now Betula pendula Roth) in the growing of raw material for veneer industry. Calculations were made on the grade, value, and price of pruned and untreated butt logs as well as on costs of pruning and the development of pruned trees.

The grade distribution of unpruned veneer butt logs, the grade distribution of the veneer yield, and consequently, the value of veneer yield and log prices at the plant are considerably better than those of average logs. The grade, value and price increased with increasing diameter. The value and price of pruned butt logs depended primarily on the difference between the turning pruning diameters, and their increase with decreasing pruning diameter and increasing turning diameter. The value of pruned butt logs is always considerably higher than that of unpruned logs. The increase in the value correlates to the pruning and turning diameters, and is, for example, in rotary-cut logs which have been pruned when 10 cm in diameter 80–130%.

Pruning increases the stumpage in naturally regenerated silver birch stands on Oxalis-Myrtillus site by 2,000–3,000 Fmk/ha when employed at 20 years of stand age and rotary cutting at 60–80 years of age respectively. The average pruning costs on Oxalis-Myrtillus site are 51–57 Fmk/ha.

The PDF includes a summary English.

  • Heiskanen, ORCID ID:E-mail:
article id 7167, category Article
Veijo Heiskanen. (1966). Tutkimuksia rauduskoivikon karsimisen kannattavuudesta. Acta Forestalia Fennica vol. 81 no. 2 article id 7167. https://doi.org/10.14214/aff.7167
English title: Studies on the profitability of pruning of common birch (Betula pendula) stands.

The objective of the present investigation was to clarify the profitability of pruning silver birch (Betula verrucosa, now Betula pendula Roth) in the growing of raw material for veneer industry. Calculations were made on the grade, value, and price of pruned and untreated butt logs as well as on costs of pruning and the development of pruned trees.

The grade distribution of unpruned veneer butt logs, the grade distribution of the veneer yield, and consequently, the value of veneer yield and log prices at the plant are considerably better than those of average logs. The grade, value and price increased with increasing diameter. The value and price of pruned butt logs depended primarily on the difference between the turning pruning diameters, and their increase with decreasing pruning diameter and increasing turning diameter. The value of pruned butt logs is always considerably higher than that of unpruned logs. The increase in the value correlates to the pruning and turning diameters, and is, for example, in rotary-cut logs which have been pruned when 10 cm in diameter 80–130%.

Pruning increases the stumpage in naturally regenerated silver birch stands on Oxalis-Myrtillus site by 2,000–3,000 Fmk/ha when employed at 20 years of stand age and rotary cutting at 60–80 years of age respectively. The average pruning costs on Oxalis-Myrtillus site are 51–57 Fmk/ha.

The PDF includes a summary English.

  • Heiskanen, ORCID ID:E-mail:
article id 7164, category Article
Veijo Heiskanen. (1965). Puiden paksuuden ja nuoruuden kehityksen sekä oksaisuuden ja sahapuulaadun välisistä suhteista männiköissä. Acta Forestalia Fennica vol. 80 no. 2 article id 7164. https://doi.org/10.14214/aff.7164
English title: Relation between the development of the early age and thickness of trees and their branchiness in Scots pine stands in Finland.

The objective of the study was to establish the influence of the founding density of a stand and the intensity of intermediate cutting on the quality of pine saw logs stems, primarily on their branchiness. Measurements were carried out in 68 Myrtillus-type and 32 Vaccinium-type Scots pine (Pinus sylvestris L.) stands. The quality of 1,982 sample trees was assessed.

According to the results, the branchless part of the stem is longest in the older age classes of trees. In all age classes the percentage of the branchless part is highest in medium sized stems. The relative height of the crown limit is greatest in small diameter classes and continues as the thickness of the tree increases. The crown is longer in the thicker tree. The grade of the butt log is on average highest in medium sized stems. Knottiness of a log made it unsuitable for a saw log only among the thickest stems. The relative share of the u/s grade decreased as the thickness of the trees increased.

From the point of view of early development of the trees it was concluded that in all age classes the branchless part is the shorter the faster the tree has grown in diameter when it was young. Also, branches of the butt log are the bigger the faster the tree has developed when it was young. The grade of the butt log improves as the thickness of the annual rings diminishes.

To produce good quality sawn timber, the pine stands should be established dense, and the first thinnings should be delayed as much as possible. The best time for the thinning would be when the diameter of the dominant trees at stump height is 12–15 cm and when all the branches have died on the length of the butt log. After the first thinning, comparatively intense intermediate thinning may be applied.

The PDF includes a summary in English.

  • Heiskanen, ORCID ID:E-mail:
article id 7142, category Article
Seppo Ervasti. (1964). Suomen sahateollisuuden kausivaihtelu. 2. Tutkimustulokset. Acta Forestalia Fennica vol. 76 no. 2 article id 7142. https://doi.org/10.14214/aff.7142
English title: Seasonal variation in the sawmill industry of Finland II. Investigation results.

Seasonal variation in the sawmill industry of Finland was studied in an investigation based on questionnaires answered by a random sample of sawmills concerning the time period of 1958-1960. The method is described in detail in a separate article in Acta Forestalia Fennica issue 75 no. 1.

The seasonal variations in purchase of roundwood was largest in big sawmills, which purchase the main part of the timber as standing sales and buy most of the wood from the State Forest auctions at the end of September. Also, they can afford to reserve their material earlier than the smaller companies. The saw logs are mainly felled in the winter in Finland because the climatic conditions and availability of labour are best at that time. Small sawmills begin fellings a little earlier than the larger ones.

In long-transport of timber the proportion of floating decreased from 47% in 1958 to 38% in 1960. At the same time, proportion of truck transport increased from 48% to 55%. Small sawmills use almost exclusively land transport. They received almost three-fourths of their logs between January and May, because the sawing is concentrated in the first half of the year. Therefore, floating does not suit for their transport method. The larger the sawmill, the later is the seasonal peak of log deliveries. The output of the big sawmills is distributed more evenly thoughout the year. The smaller the sawmill, the quicker is the turnover of raw material and the smaller the sawlog inventories.

The seasonal variation in output is sharper at small sawmills where sawing is concentrated in the first half of the year. The seasonal peak of the early spring is due to the aim at getting the sawn wood to dry early enough for shipments in the summer. Air drying takes an average of 4 ½ months. Kiln drying is more common at the larger sawmills, and gives them more flexibility. Due to the large seasonal variation in operation, the capacity of the small mills is poorly utilized. Domestic sales of sawn wood levels up the seasonality of the deliveries. Export sales are concentrated at the end and turn of the year. Also, the seasonal peak of expenditure occurs in the winter, but that of income in the summer.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7142, category Article
Seppo Ervasti. (1964). Suomen sahateollisuuden kausivaihtelu. 2. Tutkimustulokset. Acta Forestalia Fennica vol. 76 no. 2 article id 7142. https://doi.org/10.14214/aff.7142
English title: Seasonal variation in the sawmill industry of Finland II. Investigation results.

Seasonal variation in the sawmill industry of Finland was studied in an investigation based on questionnaires answered by a random sample of sawmills concerning the time period of 1958-1960. The method is described in detail in a separate article in Acta Forestalia Fennica issue 75 no. 1.

The seasonal variations in purchase of roundwood was largest in big sawmills, which purchase the main part of the timber as standing sales and buy most of the wood from the State Forest auctions at the end of September. Also, they can afford to reserve their material earlier than the smaller companies. The saw logs are mainly felled in the winter in Finland because the climatic conditions and availability of labour are best at that time. Small sawmills begin fellings a little earlier than the larger ones.

In long-transport of timber the proportion of floating decreased from 47% in 1958 to 38% in 1960. At the same time, proportion of truck transport increased from 48% to 55%. Small sawmills use almost exclusively land transport. They received almost three-fourths of their logs between January and May, because the sawing is concentrated in the first half of the year. Therefore, floating does not suit for their transport method. The larger the sawmill, the later is the seasonal peak of log deliveries. The output of the big sawmills is distributed more evenly thoughout the year. The smaller the sawmill, the quicker is the turnover of raw material and the smaller the sawlog inventories.

The seasonal variation in output is sharper at small sawmills where sawing is concentrated in the first half of the year. The seasonal peak of the early spring is due to the aim at getting the sawn wood to dry early enough for shipments in the summer. Air drying takes an average of 4 ½ months. Kiln drying is more common at the larger sawmills, and gives them more flexibility. Due to the large seasonal variation in operation, the capacity of the small mills is poorly utilized. Domestic sales of sawn wood levels up the seasonality of the deliveries. Export sales are concentrated at the end and turn of the year. Also, the seasonal peak of expenditure occurs in the winter, but that of income in the summer.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7126, category Article
Viljo Holopainen. (1960). On the price elasticity of the supply of sawn wood for export. Acta Forestalia Fennica vol. 73 no. 4 article id 7126. https://doi.org/10.14214/aff.7126

The present investigation is concerned with the price elasticity of sawn wood, concentrating on the price elasticity of sawn wood supply for export. The supply of sawn wood for export is referred to the joint attitude to price changes of all producers participating in the market.

The study concludes that producers cannot in the short- and medium-term view use the price parameter to increase total utilization in the sawn wood market. Demand holds a primary position in price formation. The capacity reserve of the sawmills permits great variations in output at the mill level, and thus elasticity in the supply of sawn wood. High timber costs are typical for the industry. Supply of roundwood can easily be adapted even to large variations in demand. The price elasticity of roundwood supply is rather great.

The long process of sawn wood production and the resulting relatively long lead-time of deliveries result in a long adaptation time of supply. Expansion and contraction of sawn wood exports cause, via the effect of exports, on income similar fluctuations in the domestic sales of sawn wood. This weakens the price elasticity of exports in some degree.

The ‘instantaneous elasticity’ upwards of sawn wood supply might be great, but speculation with stocks at the different levels of production often makes it ‘incalculable’. The price elasticity of a medium-long and long period can be expected to be relatively great upwards. The downward elasticity of a period of medium length is probably small. The elasticity of a prolonged period may be influenced by the substitution of other materials for sawn wood.

The PDF includes a summary in Finnish.

  • Holopainen, ORCID ID:E-mail:
article id 7125, category Article
L. Runeberg. (1960). European trade in raw wood during the 1950’s and prospects in the days of EEC and EFTA. Acta Forestalia Fennica vol. 73 no. 3 article id 7125. https://doi.org/10.14214/aff.7125

This paper concentrates on the roundwood commerce in Western Europe as seen from the point of view of Finland, considering the role of Eastern Europe. The first part analyses exports and imports both quantitatively and qualitatively, and the balance of the trade in the export countries. Second part covers the new market groups in Europe and the opportunities for a common market.

Arter the Second World War, a surprisingly large trade in roundwood reappeared in Europe. The European countries exported in average 11 million m3 of roundwood annually, of which 4.3 million m3 was pulpwood, and 2.8 million m3 pitprops. Finland leads exports during the 1950s with a yearly average of 4.2 million m3, followed by France and Sweden. Western Germany is the largest importing country with a negative balance of 2.8 million m3. It is concluded, from a theoretical point of view, that in Western Europe only Finland can maintain a large roundwood export. From a national point of view, however, it would be more favourable to expand the countries’ own refining industries.

On the whole, it seems as if the European roundwood trade should continue on a rather large scale during the 1960s, partly because the border trade can be expected to increase, with a freer trade, and partly because the European timber deficit needs filling from sources outside Europe. In addition, the pulp industries in the importing countries will compete more and more keenly with the exporting countries for pulpwood supplies.

The PDF includes a summary in Finnish.

  • Runeberg, ORCID ID:E-mail:
article id 7123, category Article
Seppo Ervasti. (1960). Moitteet ja välimiesmenettelyt Suomen sahatavaran viennissä. Acta Forestalia Fennica vol. 73 no. 1 article id 7123. https://doi.org/10.14214/aff.7123
English title: Claims and arbitration in exports of sawn goods from Finland.

This study concentrates on claims made against Finnish shippers or referred to arbitration by foreign buyers. The material is collected from two inquiries on claims and arbitrations, sent by the Finnish Sawmill Owners’ Association to Finnish sawmills engaged to exportation in 1954 and 1958.

On average the claims concerned about 5% of the sawn goods exported from Finland. They affected about 3% of the deliveries from the large sawmills, 10% of the deliveries of medium-sized sawmills and 15–20% of the small sawmills. In large consignments of raw material, variations in quality are not so marked as in smaller ones. Also, the grading of goods is stricter in the larger sawmills, and as they have well-established business relations, they have better opportunities to select goods with a view to demand of the buyer and the marketing areas.

The ratio of goods claimed was least in exports to remote countries, on the Western European markets in exports to Great Britain and the Netherlands. In Belgium, the ratio was high. In 1954 and 1958 approximately 12% of the claims were referred to arbitration. The bigger the sawmills, then on average the smaller the ratio of cases of arbitration in the number of claims. In Belgium, disputes have had to be settled by arbitration most frequently. Over 90% of the claims were made because of defects in quality or condition. About 5% were in respect of the specification of dimensions, and only 5% were related to other reasons than the good themselves. The sums paid for claims connected to the goods in 1958 represented only 54% of those demanded by the buyers. It would perhaps be advisable to consider the formulation of generally acceptable rules of the grading of export timber according to categories of shippers with definition of the minimum standard for each grade.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7123, category Article
Seppo Ervasti. (1960). Moitteet ja välimiesmenettelyt Suomen sahatavaran viennissä. Acta Forestalia Fennica vol. 73 no. 1 article id 7123. https://doi.org/10.14214/aff.7123
English title: Claims and arbitration in exports of sawn goods from Finland.

This study concentrates on claims made against Finnish shippers or referred to arbitration by foreign buyers. The material is collected from two inquiries on claims and arbitrations, sent by the Finnish Sawmill Owners’ Association to Finnish sawmills engaged to exportation in 1954 and 1958.

On average the claims concerned about 5% of the sawn goods exported from Finland. They affected about 3% of the deliveries from the large sawmills, 10% of the deliveries of medium-sized sawmills and 15–20% of the small sawmills. In large consignments of raw material, variations in quality are not so marked as in smaller ones. Also, the grading of goods is stricter in the larger sawmills, and as they have well-established business relations, they have better opportunities to select goods with a view to demand of the buyer and the marketing areas.

The ratio of goods claimed was least in exports to remote countries, on the Western European markets in exports to Great Britain and the Netherlands. In Belgium, the ratio was high. In 1954 and 1958 approximately 12% of the claims were referred to arbitration. The bigger the sawmills, then on average the smaller the ratio of cases of arbitration in the number of claims. In Belgium, disputes have had to be settled by arbitration most frequently. Over 90% of the claims were made because of defects in quality or condition. About 5% were in respect of the specification of dimensions, and only 5% were related to other reasons than the good themselves. The sums paid for claims connected to the goods in 1958 represented only 54% of those demanded by the buyers. It would perhaps be advisable to consider the formulation of generally acceptable rules of the grading of export timber according to categories of shippers with definition of the minimum standard for each grade.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7123, category Article
Seppo Ervasti. (1960). Moitteet ja välimiesmenettelyt Suomen sahatavaran viennissä. Acta Forestalia Fennica vol. 73 no. 1 article id 7123. https://doi.org/10.14214/aff.7123
English title: Claims and arbitration in exports of sawn goods from Finland.

This study concentrates on claims made against Finnish shippers or referred to arbitration by foreign buyers. The material is collected from two inquiries on claims and arbitrations, sent by the Finnish Sawmill Owners’ Association to Finnish sawmills engaged to exportation in 1954 and 1958.

On average the claims concerned about 5% of the sawn goods exported from Finland. They affected about 3% of the deliveries from the large sawmills, 10% of the deliveries of medium-sized sawmills and 15–20% of the small sawmills. In large consignments of raw material, variations in quality are not so marked as in smaller ones. Also, the grading of goods is stricter in the larger sawmills, and as they have well-established business relations, they have better opportunities to select goods with a view to demand of the buyer and the marketing areas.

The ratio of goods claimed was least in exports to remote countries, on the Western European markets in exports to Great Britain and the Netherlands. In Belgium, the ratio was high. In 1954 and 1958 approximately 12% of the claims were referred to arbitration. The bigger the sawmills, then on average the smaller the ratio of cases of arbitration in the number of claims. In Belgium, disputes have had to be settled by arbitration most frequently. Over 90% of the claims were made because of defects in quality or condition. About 5% were in respect of the specification of dimensions, and only 5% were related to other reasons than the good themselves. The sums paid for claims connected to the goods in 1958 represented only 54% of those demanded by the buyers. It would perhaps be advisable to consider the formulation of generally acceptable rules of the grading of export timber according to categories of shippers with definition of the minimum standard for each grade.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7121, category Article
Viljo Holopainen. (1960). Marketing roundwood in Finland and the Scandinavian Countries. With special regard to marketing channels and trade customs. Acta Forestalia Fennica vol. 72 no. 4 article id 7121. https://doi.org/10.14214/aff.7121

The present investigation set out to find out the structures of supply and demand, channels and methods of marketing, developments in marketing methods, trade customs, similarities and differences in marketing of the private forest owners and the State, local features of the market of domestic roundwood trade in Finland, and compares marketing of unprocessed wood between Finland and Scandinavian countries. The study is based on statistics of various sections of trade and from the State Boards of Forestry.

The channels of marketing from private forests in Finland and the Scandinavian countries are different. In Norway the wood is primarily marketed through the forest owners’ associations, in Finland direct individual selling is applied, while in Sweden both channels are common. In Norway and in Sweden the forest owners’ marketing organizations were probably formed mainly to protect the forest owners’ interest in price formation. The price is determined on the organizational level, while in Finland the price formation mechanism has retained a competitive nature. In Sweden the creation of demand for roundwood has been one reason for establishment of the associations, which have established new forest industry particularly in areas of low demand.

The institutions affect also the trade customs in Norway and Sweden. For instance, measuring of roundwood is performed in Scandinavia according to detailed public regulations and often carried out by the officials of special measuring boards. The Forms Committee has also since 1950 brought significant unification in the trade customs of Finland. Greatest differences in trade customs between the State and private forestry is observed in Finland.

The producer’s role in marketing has increased since 1930s, which is demonstrated by the increasing activity in marketing by the forest owners’ associations in Norway and Sweden. Also, the relative importance of sales with contract for delivery has been growing. A second line of development appears in the more detailed norms in trade customs.

The PDF includes a summary in Finnish.

  • Holopainen, ORCID ID:E-mail:
article id 7488, category Article
Viljo Holopainen. (1959). The concept of a roundwood price level and its determination in forestry. Acta Forestalia Fennica vol. 68 no. 6 article id 7488. https://doi.org/10.14214/aff.7488

Roundwood statistics are essential in a country such as Finland, where the roundwood market costitutes one of the most important internal markets. Determining the price level of roundwood can, however, be problematic due to the difficulty of the empirical determination. The main difficulties are the many timber assortments, quality differcences within a timber assortment, large variation of local prices due to variations in demand and harvesting conditions and in sales methods. The article discusses these problems from the perspective of composing a roundwood statistics for different timber assortments that would allow local and temporal comparison of the prices. It seems impossible to compose price statistics that could eliminate totally the variation in the material, transport conditions and demand fluctuations caused by technical development. However, one can suffice to a compromise that would eliminate the major disturbances and take into account other factors that are not related with market when studying the price series. In addition, the paper discusses methods for calculation of price indices.

The PDF includes a summary in Finnish.

  • Holopainen, ORCID ID:E-mail:
article id 7484, category Article
Seppo Ervasti. (1959). Suomen havusahatavaranmyynnin kausi- ja suhdannevaihteluista vuosina 1951-1958. Acta Forestalia Fennica vol. 68 no. 2 article id 7484. https://doi.org/10.14214/aff.7484
English title: On the seasonal and business cycle fluctuations of Finnish sawn softwood sales in 1951-1958.

The investigation examines export sales of Finnish sawn softwood sales in 1951-1958, concentrating on the volume of the sales. The material was collected from the archives of Finnish Sawmill Owner’s Association and the Finnish Sawmill Control Organization and the annual reports of the former. Correlation analysis was used in assessing the interdependence of the monthly sales volume and the price, and opening sales and the total sales volume of the year.

A slightly negative correlation was seen between the sale price and the monthly sales volume. Goods sold at under average prices are more abundant than goods sold at over average prices. Generally, with a rising price trend, the annual sales volume increased, but with falling prices the situation was reverse. The sales volume has been dependent on the business cycle development of prices. There was positive correlation between the opening sales and the total sales quantity for the year. The sales volume was at its maximum in the period between November and January, and at the minimum between March and September.

The time of the sales made to different countries differed little judged by quarterly statistics. It seems that the major shippers have generally concluded opening sales first. Northern Finnish shippers and the small shippers of Southern Finland have sold proportionately least during the last quarter. In general, the poorer the qualities in question the smaller on an average the proportion of opening sales but the greater the share of clearance sales.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7480, category Article
Seppo Ervasti. (1958). Suomesta myydyn havusahatavaran hintasuhteiden muutokset vuosina 1932-38 ja 1951-56. Acta Forestalia Fennica vol. 67 no. 6 article id 7480. https://doi.org/10.14214/aff.7480
English title: Changes in the price ratios of sawn softwood sold by Finland in 1932-38 and 1951-56.

The aim of the investigation was to estimate the changes in the price ratios of different tree species of sawn timber, timber sizes and qualities, the ratios of the prices obtained by different shippers and from different countries, and their changes, especially the trends and business cycles. The data can be utilized in the organization of sawing and the drawing up of the price scales. The price ratios were calculated by taking 100 as the basic quantity and calculating the values for the other quantities accordingly, the values are called price indices. The data is collected from the sales reports in the archives of the Finnish Sawmill Owners’ Association.

Comparing the ratios of the basic prices, the prices of unsorted pine goods by shipper B (the leading marks of Northern Finland), were considerably higher than the others. The North Finnish pine goods are of the best quality in Finland. The price differences between the other shippers were small. The prices of unsorted spruce goods differed very little with different shippers. In some years the basic prices obtained for pine from different countries showed considerable differences although, in the overall view, the differences were small.

In the leading marks of Northern Finland, the differences between pine and spruce prices was greater than the other price differences. The quality of pine logs in Northern Finland is extremely high. During the periods of prosperity, the price difference between pine and spruce was relatively smaller than during depression. With spruce goods, the relative price difference for the qualities is smaller than with pine goods. For the both species the relative price differences diminished with the increase in the basic price. In the broadest sizes of unsorted pine goods, the price difference of the inch class is much bigger than in the small sizes. This is true especially for boards. The relative price difference between boards and battens increased distinctly with the advance in the basic price. A similar, though not as clear change took place in the price ratio of board and 7” sizes. The price differences between battens and boards are much smaller for spruce than for pine. The trends of the price indices of the different sizes show from the middle of 1920s and as far as the 9” u/s pine sizes very gentle, and in regards of the corresponding spruce sizes, a fairly sharp rising tendency.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7480, category Article
Seppo Ervasti. (1958). Suomesta myydyn havusahatavaran hintasuhteiden muutokset vuosina 1932-38 ja 1951-56. Acta Forestalia Fennica vol. 67 no. 6 article id 7480. https://doi.org/10.14214/aff.7480
English title: Changes in the price ratios of sawn softwood sold by Finland in 1932-38 and 1951-56.

The aim of the investigation was to estimate the changes in the price ratios of different tree species of sawn timber, timber sizes and qualities, the ratios of the prices obtained by different shippers and from different countries, and their changes, especially the trends and business cycles. The data can be utilized in the organization of sawing and the drawing up of the price scales. The price ratios were calculated by taking 100 as the basic quantity and calculating the values for the other quantities accordingly, the values are called price indices. The data is collected from the sales reports in the archives of the Finnish Sawmill Owners’ Association.

Comparing the ratios of the basic prices, the prices of unsorted pine goods by shipper B (the leading marks of Northern Finland), were considerably higher than the others. The North Finnish pine goods are of the best quality in Finland. The price differences between the other shippers were small. The prices of unsorted spruce goods differed very little with different shippers. In some years the basic prices obtained for pine from different countries showed considerable differences although, in the overall view, the differences were small.

In the leading marks of Northern Finland, the differences between pine and spruce prices was greater than the other price differences. The quality of pine logs in Northern Finland is extremely high. During the periods of prosperity, the price difference between pine and spruce was relatively smaller than during depression. With spruce goods, the relative price difference for the qualities is smaller than with pine goods. For the both species the relative price differences diminished with the increase in the basic price. In the broadest sizes of unsorted pine goods, the price difference of the inch class is much bigger than in the small sizes. This is true especially for boards. The relative price difference between boards and battens increased distinctly with the advance in the basic price. A similar, though not as clear change took place in the price ratio of board and 7” sizes. The price differences between battens and boards are much smaller for spruce than for pine. The trends of the price indices of the different sizes show from the middle of 1920s and as far as the 9” u/s pine sizes very gentle, and in regards of the corresponding spruce sizes, a fairly sharp rising tendency.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7471, category Article
Kalle Putkisto. (1956). Tutkimuksia pyörätraktoreiden käytöstä puutavaran metsäkuljetuksessa. Acta Forestalia Fennica vol. 66 no. 1 article id 7471. https://doi.org/10.14214/aff.7471
English title: Investigations of the use of wheel tractors for the forest transport of timber.

Forest transport of timber in Finland has been arranged as horse haulage during winter time using horses vacant from farm work. Tractors have now begun to replace horses in agriculture, which will lead to shortage of horses for timber harvesting in future. The aim of this investigation was to find a method of mechanized forest transport suitable for Finnish conditions. The method should be provided by an agricultural wheel tractor that is shared with agriculture. It should also be applicable to timber transport of relatively small forest holdings.

A method for time studies of tractor driven timber harvesting was developed. The competitivity of tractor transport of timber against the traditional method was studied in four pulpwood harvesting sites. The results suggest that if the tractor forest transport method in question is to be applied in practice, conditions should first be chosen which favour it most. A tractor forest transport method evolved on the basis of experiments presupposes certain conditions to be successful. These include snow for the construction of the packed-snow driveway, frost to harden the driveway, the location of strip roads in relatively easy topography, and of the main haulage road that is gently sloping in the haulage-loaded direction. The optimal transport distance for this method are about 3-10 km.

The PDF includes a summary in English.

  • Putkisto, ORCID ID:E-mail:
article id 7471, category Article
Kalle Putkisto. (1956). Tutkimuksia pyörätraktoreiden käytöstä puutavaran metsäkuljetuksessa. Acta Forestalia Fennica vol. 66 no. 1 article id 7471. https://doi.org/10.14214/aff.7471
English title: Investigations of the use of wheel tractors for the forest transport of timber.

Forest transport of timber in Finland has been arranged as horse haulage during winter time using horses vacant from farm work. Tractors have now begun to replace horses in agriculture, which will lead to shortage of horses for timber harvesting in future. The aim of this investigation was to find a method of mechanized forest transport suitable for Finnish conditions. The method should be provided by an agricultural wheel tractor that is shared with agriculture. It should also be applicable to timber transport of relatively small forest holdings.

A method for time studies of tractor driven timber harvesting was developed. The competitivity of tractor transport of timber against the traditional method was studied in four pulpwood harvesting sites. The results suggest that if the tractor forest transport method in question is to be applied in practice, conditions should first be chosen which favour it most. A tractor forest transport method evolved on the basis of experiments presupposes certain conditions to be successful. These include snow for the construction of the packed-snow driveway, frost to harden the driveway, the location of strip roads in relatively easy topography, and of the main haulage road that is gently sloping in the haulage-loaded direction. The optimal transport distance for this method are about 3-10 km.

The PDF includes a summary in English.

  • Putkisto, ORCID ID:E-mail:
article id 7462, category Article
Seppo Ervasti. (1955). Suomesta Pohjanmeren maihin vuosina 1920-1952 viety havusahatavara : koostumuksen muutokset. Acta Forestalia Fennica vol. 64 no. 2 article id 7462. https://doi.org/10.14214/aff.7462
English title: Export of sawn softwood from Finland to the North Sea Countries in 1920-1952.

The objective of the investigation was to study the trends and fluctuations in the composition of sawn goods, changes due to business cycles, and casual fluctuations. The subject is confined to sawn softwood export to Great Britain, the Netherlands, Belgium and France (The North Sea countries) in 1920-1952. The data was based mainly on statistics of the Board of Customs, Series of Foreign Trade, Finnish Sawmill Owner’s Association and the Finnish Official Statistics.

The North Sea countries took 75-85% of the sawn softwood exported from Finland before World War II, and 50-70% of the quantity exported since the war. Sawn softwood export from Finland is almost exclusively long and small-dimension timber. The composition of the export from Finland to the North Sea countries was defined already during the 1900th century, and no big chances were observed even during the period of 1920-1952. The only definite trend was decrease in the proportion of u/s grade.

The PDF includes a summary in English.

  • Ervasti, ORCID ID:E-mail:
article id 7448, category Article
Viljo Holopainen. (1954). Suomen havusahatavaran viennin kausimaisuus. Acta Forestalia Fennica vol. 61 no. 36 article id 7448. https://doi.org/10.14214/aff.7448
English title: The seasonal fluctuations in the Finnish exports of sawn softwood.

The purpose of the investigation was to examine the seasonal pattern in Finnish export shipments and export sales of sawn softwood in 1927-1953. Statistics concerning shipments have been obtained from the Board of Customs, and material relating to sales has been provided by the Finnish Sawmill Owner’s Association (now Finnish Sawmills Association). On the basis of original monthly statistics, 13-month moving averages were computed. Finally, a seasonal index was calculated.

According to the results, the export shipments have a fairly apparent seasonal pattern with very low figures from January to April, a peak from June to August, and thereafter a gradual decline up to the end of the year. There are also considerable variations from year to year but in general the exports follow this rhythm. In contrast to export shipments the seasonal pattern of export sales is characterised by significant irregularity. Market developments and speculation play a far greater role than the seasonal factors. Indeed, a seasonal character in export sales can scarcely be discerned.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.

The PDF includes a summary in English.

  • Holopainen, ORCID ID:E-mail:
article id 7445, category Article
Jaakko Vöry. (1954). Puutavaran valmistuksen keskityötulosten määrittäminen tilastoteitse. Acta Forestalia Fennica vol. 61 no. 33 article id 7445. https://doi.org/10.14214/aff.7445
English title: Statistical determination of the average work performance in the preparation of timber.

Work studies conducted in Finland and Sweden on forest work have shown that the performance of different workers or even of a same worker vary greatly, although external conditions such as the size and other properties of the trees, weather etc. are similar. It has been decided in the Northern Countries that as it is impossible to assess the working speed of a man, it is not possible to find out the average work performances, not even from long term time studies. The only way is to collect performance statistics.

Metsäteho (Forest Work Studies Section of the Central Association of Finnish Woodworking Industries) has collected since 1946 statistics on the working sites of forest industry companies in different parts of Finland on the preparation on timber. To make it comparable the material has been converted to uniform values by using the ratios given by the work time studies of various forest jobs conducted by Metsäteho. The ratios are necessary in trying to determine average performances by statistical means. The actual length of time each man is at work on different days and the actual number of days is needed, because in Finland the workers can themselves decide fairly freely the length of a working day. In forest work, wages are paid for the quantity prepared, not for time. The statistics collected by Metsäteho include information on the length of the working days, and conditions in each forest, such as the size of the trees, form of stem, branchiness, bark thickness, terrain, density of the forest, weather conditions etc.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.

The PDF includes a summary in English.

  • Vöry, ORCID ID:E-mail:
article id 7437, category Article
Kustaa Kallio. (1954). Asutustoiminnassa muodostettujen viljelystilojen metsämaa-alojen suuruussuhteista. Acta Forestalia Fennica vol. 61 no. 25 article id 7437. https://doi.org/10.14214/aff.7437
English title: Area of wood lots of the farms established in connection with settlement in Finland.

In Finland a large land reform has been accomplished which has increased the number of small farms and forest holdings by over 100,000. It is estimated that 4-5 million ha of forest land has been transferred to these smallholdings. The aim of this investigation was to study the areas of the wood lots of the farms established in connection to settlement activities during the time Finland has been independent.

The study shows that the farms established on the state-owned lands have been given forest areas big enough to enable them timber sales, provided that the forests were in a moderately good silvicultural condition. Relatively largest forest areas have been given to farms established from tenant farms. The farms established on private lands have got in average forest areas that are smaller than would be required for growing of household timber. In Southern Finland the area has been adequate, but in Northern Finland too small in part of the farms. Also, variation in the size of the farms has been larger. The farms established under the Land Acquisition Act have been given in average more than the principle of according to which half of the forests should be suitable for cultivation of household timber and half for timber sales.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.

The PDF includes a summary in German.

  • Kallio, ORCID ID:E-mail:
article id 7435, category Article
Esko Kangas. (1954). On the possibility of pests being conveyed in export timber : survey of biological requirements. Acta Forestalia Fennica vol. 61 no. 23 article id 7435. https://doi.org/10.14214/aff.7435

Many countries have enacted plant protection laws or statutes that consist timber imported into a country, both raw wood and processed timber. This has caused some inconvenience to the international timber trade. Necessary protection against the spread of pests via export is fully acceptable, but the protection should be based on actual need.
When considering processed or barked raw timber, the problem concerns only species that pass their development in the wood. The four most important biological requirements affecting the risk are 1) the tree species of the importing country and affinity of the pest, 2) climatic conditions of the importing country and the pest’s range and adaptability to the climate, 3) biological factors regulating the population, and 4) suitability of the individual development of the pest for transmission. These risks are discussed in the article.

It is concluded that it is possible largely to eliminate the species that might be conveyed via export timber. It is often possible to decide in advance what danger threatens the importing country from species that might be conveyed via export timber. This would make it possible to adapt plant protection regulations to suit the relation between the exporting and importing countries.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.

  • Kangas, ORCID ID:E-mail:
article id 7435, category Article
Esko Kangas. (1954). On the possibility of pests being conveyed in export timber : survey of biological requirements. Acta Forestalia Fennica vol. 61 no. 23 article id 7435. https://doi.org/10.14214/aff.7435

Many countries have enacted plant protection laws or statutes that consist timber imported into a country, both raw wood and processed timber. This has caused some inconvenience to the international timber trade. Necessary protection against the spread of pests via export is fully acceptable, but the protection should be based on actual need.
When considering processed or barked raw timber, the problem concerns only species that pass their development in the wood. The four most important biological requirements affecting the risk are 1) the tree species of the importing country and affinity of the pest, 2) climatic conditions of the importing country and the pest’s range and adaptability to the climate, 3) biological factors regulating the population, and 4) suitability of the individual development of the pest for transmission. These risks are discussed in the article.

It is concluded that it is possible largely to eliminate the species that might be conveyed via export timber. It is often possible to decide in advance what danger threatens the importing country from species that might be conveyed via export timber. This would make it possible to adapt plant protection regulations to suit the relation between the exporting and importing countries.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.

  • Kangas, ORCID ID:E-mail:
article id 7435, category Article
Esko Kangas. (1954). On the possibility of pests being conveyed in export timber : survey of biological requirements. Acta Forestalia Fennica vol. 61 no. 23 article id 7435. https://doi.org/10.14214/aff.7435

Many countries have enacted plant protection laws or statutes that consist timber imported into a country, both raw wood and processed timber. This has caused some inconvenience to the international timber trade. Necessary protection against the spread of pests via export is fully acceptable, but the protection should be based on actual need.
When considering processed or barked raw timber, the problem concerns only species that pass their development in the wood. The four most important biological requirements affecting the risk are 1) the tree species of the importing country and affinity of the pest, 2) climatic conditions of the importing country and the pest’s range and adaptability to the climate, 3) biological factors regulating the population, and 4) suitability of the individual development of the pest for transmission. These risks are discussed in the article.

It is concluded that it is possible largely to eliminate the species that might be conveyed via export timber. It is often possible to decide in advance what danger threatens the importing country from species that might be conveyed via export timber. This would make it possible to adapt plant protection regulations to suit the relation between the exporting and importing countries.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.

  • Kangas, ORCID ID:E-mail:
article id 7434, category Article
Jarl Lindfors. (1954). Sahatukkien kaukokuljetuksen eräitä piirteitä. Acta Forestalia Fennica vol. 61 no. 22 article id 7434. https://doi.org/10.14214/aff.7434
English title: Long-distance transport of saw logs in Finland.

Central Association of Finnish Forest Industries decided in 1953 to begin collecting annual statistics of timber transportation of its members. The survey of members covers almost 97% of the timber transportations of the member companies, which have production over 1,000 cu ft. In all 79 companies answered the survey. Their total timber transportation was 166,4 million cu ft in 1952.

The long-distance transportation of saw logs by horse transport directly to the mill or other such location was 1,297 cu ft, by truck transport 42,644 cu ft, by rail transport 6,707 cu ft, and by water transport 115,789 cu ft. The average transportation distance was for horse transport 2.4 km, truck transport 27 km, rail transport 224 km and water transport 209 km.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.
The PDF includes a summary in German.

  • Lindfors, ORCID ID:E-mail:
article id 7431, category Article
Lauri Heikinheimo. (1954). Sahatavaran vientitulon jakaantumisesta vuosina 1913-1953. Acta Forestalia Fennica vol. 61 no. 19 article id 7431. https://doi.org/10.14214/aff.7431
English title: On the distribution of income from Finnish sawn timber exports in 1913-1953.

The investigation studies the development of a logger’s daily earnings, a sawmill worker’s hourly earnings, saw timber stumpage prices and saw timber export prices, expressed in marks in Finland in 1913-1953, concentrating upon the trends of real value.

Although worker’s earnings in forestry and sawmilling have developed differently especially in the 1920s, the late 1930s and the early 1940s, their general long-time development has been very similar. On the other hand, the stumpage prices increased in real value much sharply than wages before the World War II. The real value of stumpage prices dropped because of economic regulation measures in the 1940s until regulation was abolished and the Korean War boom raised them in 1951, to fall after that. The development depends partly of the development of export prices for sawn timber.

Without changing the distribution of income from exports the real value of labour earnings, measured by export prices, may rise at most at a pace corresponding to the productivity of work. In logging there has been no actual increase in the productivity in the 20th century. As the increase in the productivity in timber transportation has probably been absorbed in increased wages and capital costs in the branch, a rise in forest labour’s real earnings and stumpage is possible only by means of a rise in the productivity of sawmilling or a change in the distribution of export income. It seems that from the end of World War I up to the middle of 1920s this increase of productivity and in export prices of sawn timber was shared only by capital and possibly mill labour. After that up to World War II stumpage prices rose so steeply that they swallowed the entire increase in productivity and reduced capital’s share of the export price. In the 40s the level of earnings followed the trend of productivity in industry, made possible by a sharp reduction in stumpage.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.
The PDF includes a summary in English.

  • Heikinheimo, ORCID ID:E-mail:
article id 7431, category Article
Lauri Heikinheimo. (1954). Sahatavaran vientitulon jakaantumisesta vuosina 1913-1953. Acta Forestalia Fennica vol. 61 no. 19 article id 7431. https://doi.org/10.14214/aff.7431
English title: On the distribution of income from Finnish sawn timber exports in 1913-1953.

The investigation studies the development of a logger’s daily earnings, a sawmill worker’s hourly earnings, saw timber stumpage prices and saw timber export prices, expressed in marks in Finland in 1913-1953, concentrating upon the trends of real value.

Although worker’s earnings in forestry and sawmilling have developed differently especially in the 1920s, the late 1930s and the early 1940s, their general long-time development has been very similar. On the other hand, the stumpage prices increased in real value much sharply than wages before the World War II. The real value of stumpage prices dropped because of economic regulation measures in the 1940s until regulation was abolished and the Korean War boom raised them in 1951, to fall after that. The development depends partly of the development of export prices for sawn timber.

Without changing the distribution of income from exports the real value of labour earnings, measured by export prices, may rise at most at a pace corresponding to the productivity of work. In logging there has been no actual increase in the productivity in the 20th century. As the increase in the productivity in timber transportation has probably been absorbed in increased wages and capital costs in the branch, a rise in forest labour’s real earnings and stumpage is possible only by means of a rise in the productivity of sawmilling or a change in the distribution of export income. It seems that from the end of World War I up to the middle of 1920s this increase of productivity and in export prices of sawn timber was shared only by capital and possibly mill labour. After that up to World War II stumpage prices rose so steeply that they swallowed the entire increase in productivity and reduced capital’s share of the export price. In the 40s the level of earnings followed the trend of productivity in industry, made possible by a sharp reduction in stumpage.

The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.
The PDF includes a summary in English.

  • Heikinheimo, ORCID ID:E-mail:
article id 7417, category Article
N. Stolpe. (1954). Uittoa, sen organisatiota ja tulevaisuutta koskevia näkemyksiä. Acta Forestalia Fennica vol. 61 no. 5 article id 7417. https://doi.org/10.14214/aff.7417
English title: Observations on floating, its organizations and future in Finland.

The costs of floating have increased by about 20-fold after the Second World War in Finland, which has raised concerns in the forest sector. At the same time, the costs of road transport have increased by 16% and costs of rail transport by 15%. Floating has been replaced mainly by road transport in transport of roundwood, especially near the factories. This development is likely to continue as new roads are built and the truck fleet develops.  

In spite of the changes in timber transportation, floating was still the most common way of transporting roundwood in 1952: 69% of saw logs, 53% of veneer timber, 42% of domestic pulp wood, 14% of exported pulp wood and mining timber and 14% of firewood was transported by a water route. There are several ways to improve the efficiency of floating and decrease its costs. This can be achieved in two ways. First, using modern technology, such as tugboats, bundlers and other equipment, and second, improving the operation and co-operation between different actors.  

The PDF includes a summary in German. 

  • Stolpe, ORCID ID:E-mail:
article id 7415, category Article
W. E. Roitto. (1954). Eräitä näkökohtia Saimaan vesistöalueen puutavaran kaukokuljetuksen kehittymismahdollisuuksista. Acta Forestalia Fennica vol. 61 no. 3 article id 7415. https://doi.org/10.14214/aff.7415
English title: Development potential of transportation of roundwood in the river and lake system of Lake Saimaa in Finland.

About 17.5% of forest lands of Finland is situated around the river and lake system of Lake Saimaa. Furthermore, the growth of the forests  of the area correspond about 25% of the total growth of forests in Finland. The watersystem is one of the most important portages of roundwood in the country. It consists 11,000 km of floating channels, 2,000 km of which suit for floating in bundles. Annually 30-35 million cu ft of saw logs, 7 million cu ft of veneer timber and 2,5-3 million cu ft of pulp wood is floated in the area.

Even if the water system at present still suits well for floating, there are many opportunities for development, which would improve its competitiveness against other modes of transport. Several different sites where building of floating channels or improving the floatways are needed are described in the article.

The PDF includes a summary in German.

  • Roitto, ORCID ID:E-mail:
article id 7409, category Article
Eino Saari. (1954). Wald- und Holzbilanzen. Acta Forestalia Fennica vol. 60 no. 2 article id 7409. https://doi.org/10.14214/aff.7409
English title: On forest and timber balances.
Original keywords: Bilanz; Holz; Ökonomie
English keywords: balance; calculations; timber; economic

Literature knows a variety of forest and timber related balances and even wider variety of calculations concerning the themes. The article presents forest and timber balances divided into three categories, based on their purpose.

The three categories are: 1) (national) economic balances for calculating the sustainability of forest use and sufficiency of forest resources; 2) balances of yearly harvesting rates for mostly commercial purposes, but also economic uses; and 3) balances of timber demand and those for balance between supply and demand, especially for foreign trade.

Finally the author critically views the use of balances to describe the amounts of wood used in industry.

The PDF contains a summary in Finnish.
  • Saari, ORCID ID:E-mail:
article id 7403, category Article
L. Runeberg. (1950). The activities of timber agents and timber associations. Acta Forestalia Fennica vol. 58 no. 3 article id 7403. https://doi.org/10.14214/aff.7403

Selling through agencies became common Finland in the end of 1800s in timber sales and export. No joint marketing organization has been established in the sawmilling industry, as has been done in pulp and paper industry. The aim of this report was to discuss need for the agencies in the post-war situation.

The paper concludes that the timber agents fill their post even at present under the changed conditions of the timber trade. The Finnish sawmilling industry is based on a majority of small sawmills, which have difficulties in keeping up foreign connections themselves. Even to the somewhat larger sawmills, which have a salesman of their own, the services of a domestic agent can be recommended. The number of agencies has markedly decreased during the war. With 120 agencies active in Finland it is evident that a considerable part of them will disappear. In Sweden the Association of timber agents has only 33 members. In comparison to other countries, the Finnish agency firms have the greatest number of joint-stock companies. The companies are concentrated in Helsinki. A good solution for co-operation in the sector could be to found an independent timber agent’s association.

The PDF includes a summary in Finnish.

  • Runeberg, ORCID ID:E-mail:
article id 7403, category Article
L. Runeberg. (1950). The activities of timber agents and timber associations. Acta Forestalia Fennica vol. 58 no. 3 article id 7403. https://doi.org/10.14214/aff.7403

Selling through agencies became common Finland in the end of 1800s in timber sales and export. No joint marketing organization has been established in the sawmilling industry, as has been done in pulp and paper industry. The aim of this report was to discuss need for the agencies in the post-war situation.

The paper concludes that the timber agents fill their post even at present under the changed conditions of the timber trade. The Finnish sawmilling industry is based on a majority of small sawmills, which have difficulties in keeping up foreign connections themselves. Even to the somewhat larger sawmills, which have a salesman of their own, the services of a domestic agent can be recommended. The number of agencies has markedly decreased during the war. With 120 agencies active in Finland it is evident that a considerable part of them will disappear. In Sweden the Association of timber agents has only 33 members. In comparison to other countries, the Finnish agency firms have the greatest number of joint-stock companies. The companies are concentrated in Helsinki. A good solution for co-operation in the sector could be to found an independent timber agent’s association.

The PDF includes a summary in Finnish.

  • Runeberg, ORCID ID:E-mail:
article id 7403, category Article
L. Runeberg. (1950). The activities of timber agents and timber associations. Acta Forestalia Fennica vol. 58 no. 3 article id 7403. https://doi.org/10.14214/aff.7403

Selling through agencies became common Finland in the end of 1800s in timber sales and export. No joint marketing organization has been established in the sawmilling industry, as has been done in pulp and paper industry. The aim of this report was to discuss need for the agencies in the post-war situation.

The paper concludes that the timber agents fill their post even at present under the changed conditions of the timber trade. The Finnish sawmilling industry is based on a majority of small sawmills, which have difficulties in keeping up foreign connections themselves. Even to the somewhat larger sawmills, which have a salesman of their own, the services of a domestic agent can be recommended. The number of agencies has markedly decreased during the war. With 120 agencies active in Finland it is evident that a considerable part of them will disappear. In Sweden the Association of timber agents has only 33 members. In comparison to other countries, the Finnish agency firms have the greatest number of joint-stock companies. The companies are concentrated in Helsinki. A good solution for co-operation in the sector could be to found an independent timber agent’s association.

The PDF includes a summary in Finnish.

  • Runeberg, ORCID ID:E-mail:
article id 7401, category Article
Veijo Heiskanen. (1950). Tutkimuksia pinopuutavaran proomuun lastauksesta. Acta Forestalia Fennica vol. 58 no. 1 article id 7401. https://doi.org/10.14214/aff.7401
English title: Investigations on loading piled wood into barges.

In Finland, transportation of wood by vessels has decreased, but is still an important mode of transport especially for firewood. In 1941-1947, nearly 25% of the firewood procured by the State Fuel Board was transported by vessels. This investigation concentrates on loading of wood into barges, since the share of wages of total expenses is greatest in this phase. The loading work amounts to nearly 40% of the total wages.

Two methods of loading barges are used in Finland: loading from the shore and truck loading. This study concentrates on the more common method, loading from the shore. A time study was conducted on the different stages of loading and piling wood into barges, most of which is done by hand. Most time-consuming part of the work is transporting the logs to the barge with a wheelbarrow, comprising over 40% of the working time. Time required for loading firewood is almost twice as much as loading pulp wood. Recommendations for loading places and organization of work are given in the article to improve the efficiency of the work.

The PDF includes a summary in English.

  • Heiskanen, ORCID ID:E-mail:
article id 7371, category Article
Einari Wuoti. (1942). Kuusisahapuun teknillisen ja pinokuution välinen suhde sekä sen riippuvaisuus muotoluokasta. Acta Forestalia Fennica vol. 50 no. 18 article id 7371. https://doi.org/10.14214/aff.7371
English title: Relation between technical and piled cubic meter of Norway spruce saw logs and their relation to form class.

Due to shortage of large logs, sawmill industry has been forced to buy also smaller logs, which also pulp industry uses as a raw material. Sawmills must be careful in the pricing of the logs, because profitability of sawing of timber depends on the size of the logs. These industries use different measures when they buy timber: pulp industry uses piled measure in meters, while saw logs are measured individually in cubic feet. The aim of the study was to develop sets of figures on technical cubic measure of a saw log and its relation to a piled cubic meter from the same log used as pulp wood. In addition, the effect of form class on the measures was studied.

The relation was assessed for trunks that had good, mediocre or unfavourable form class, which distinction is easy to make for a forest worker buying timber. The relations can be used by a buyer of saw logs or pulpwood who need to compare the prices or when the seller of the wood compares the offers.

The PDF includes a summary in German.

  • Wuoti, ORCID ID:E-mail:
article id 7345, category Article
O. Seppänen. (1939). Tuntsa-Oulankajoen sekä Jäämeren päävesistöalueiden metsät ja niiden kaukokuljetusmahdollisuudet. Acta Forestalia Fennica vol. 47 no. 5 article id 7345. https://doi.org/10.14214/aff.7345
English title: The forests in the Tuntsa-Oulanka and the use of Arctic Ocean main water system area in long-distance transport.

The principal method of transporting timber for long distances in Finland is floating. It is supplemented in the principal forest districts by transport in ships, by rail and lorries. However, in north-eastern and northern parts of the country the main water systems flow into Arctic Ocean, and floating cannot be used to transport timber. The area does not have railroad and road network is sparse. The poor accessibility has hindered the use of forest in the area. A division of the Tuntsa-Oulanka and Arctic Ocean water system area into supply areas is presented.

The PDF includes a summary in English.

  • Seppänen, ORCID ID:E-mail:
article id 7340, category Article
P. S. Tikka. (1938). Puiden vikanaisuuksien vaikutuksesta hakkuutulokseen Perä-Pohjolan havumetsissä. Acta Forestalia Fennica vol. 46 no. 5 article id 7340. https://doi.org/10.14214/aff.7340
English title: The effect of injuries of the stems to amount of merchantable timber in the northernmost Finland.

The effect of different kinds of injuries in the amount of merchantable timber was studied in 57 sample plots in the northernmost Finland. Without any injuries the yield of timber would have been 72.3% in Scots pine (Pinus sylverstris L.) and 89.9% in Norway spruce (Picea abies (L.) H. Karst.). Butting, and removal of parts of the stems due to Injuries decreased the volume by 10.4% in pine and 13.5% in spruce. The main cause for butting of pine was fire wounds, and butt rot in spruce. Also pine blister rust (Peridermium pini and Cronartium flaccidum) causes injuries in Scots pine. The better the forest site type, the smaller is the timber discarded due to injuries. In pine 54% and in spruce 53% of the trees and were healthy. The forests in the northernmost Finland are over-mature which increase the occurrence of fire wounds and decay. Thus, forest fire control and the felling or thinning of over-mature stands will improve the quality of the timber in the long run.

The PDF includes a summary in German.

  • Tikka, ORCID ID:E-mail:
article id 7333, category Article
Valter Keltikangas. (1938). Puutase metsätalouden tuloksenlaskennassa : tulosbilanssioppiin (dynaamiseen bilanssiteoriaan) perustuva tutkimus. Acta Forestalia Fennica vol. 45 no. 1 article id 7333. https://doi.org/10.14214/aff.7333
English title: Timber balance in the financial accounting of forestry.

The financial accounting of the forestry needs redefining in Finland due to the effect of forest improvement, especially peatland drainage, on timber balance and valuation of forest land. The aim of the study was to develop methods to determine the timber balance using a separate forest land account. The problems of timber balance are related to the technical methods to assess timber balance and the cost of the work, quantitative determination of the profit, and qualitative determination of the profit. One main problem is to whether to define the quantitative profit as a sustainability of timber resources or difference in the allowable cut and outturn. The article discusses the strengths and weaknesses of the methods, and concludes that regardless of the method that is used to calculate the timber balance, profit or loss accounts have less exact nature in forestry than in other sectors. Replacing reliably calculated revenue surplus with operating result based on timber account would lead to tentative results.

The PDF includes a summary in German.

  • Keltikangas, ORCID ID:E-mail:
article id 7317, category Article
Erkki Laitakari. (1935). Tutkimuksia metsikön ja kasvupaikan vaikutuksesta kuusen rungon kelpoisuuteen. Acta Forestalia Fennica vol. 41 no. 4 article id 7317. https://doi.org/10.14214/aff.7317
English title: Studies on the influence of stand and forest site type on the quality of Norway spruce stem.

Healthy, straight, more or less free from branches and slowly tapering stems are good raw material for woodworking industry. The aim of the study was to investigate, from the stand point of forest management, the influence of stand and forest site type on the technical quality of the stems. Sample plots were measured in Norway spruce (Picea abies (L.) H. Karst.) stands in Eastern Finland. Norway spruce growing in a stand with closed crowns developed thin branches and self-pruned, if the stand was dense in the early stages. The decisive time for the stand is, therefore, when it is at seedling stage and young stand. The stems are more branchy if the stand has been planted. The adequate planting density is discussed based on earlier studies. The sufficient density seems to be achieved when the spacing is at maximum two meters. When the stems are branchless up to four meters, thinning of spruce stand does not affect knottiness or stem form. A sparsely stocked, knotty young stand does not produce good-quality timber even if the stand is later dense. Selective thinning from above can be used to improve the quality of the wood.

The PDF includes a summary in German.

  • Laitakari, ORCID ID:E-mail:
article id 7309, category Article
I. Lassila. (1934). Kestävyys puun laadun tunnuksena. Acta Forestalia Fennica vol. 40 no. 32 article id 7309. https://doi.org/10.14214/aff.7309
English title: Durability as indication of wood quality.
Original keywords: puuaine; lujuus; kestävyys; puun laatu
English keywords: wood; timber; strength; durability

The article reviews the change in how the most sufficient wood material was chosen for different uses. The craftsmen used different characteristics to determine the quality of wood, for instance, tree species, location in the stem, whether it was sapwood or heartwood etc. Scientifically, the quality of the wood has been described by, for instance, specific gravity, bending strength and compressive strength. Durability would, however, be better attribute than strength to describe the quality of wood, because circumstances, like humidity and temperature can change where the wood is used. The article discusses further the development of durability indexes.

The PDF includes a summary in German.

  • Lassila, ORCID ID:E-mail:
article id 7302, category Article
M. Lappi-Seppälä. (1934). Karsimisesta ja sen metsänhoidollisesta merkityksestä. Acta Forestalia Fennica vol. 40 no. 25 article id 7302. https://doi.org/10.14214/aff.7302
English title: The silvicultural influences of pruning.

Pruning growing trees influences tree growth and value of the wood and yield of timber of the stand. Pruning living branches create open wounds on the stems that can risk the growth of tree species that are vulnerable to injuries. For instance, pruning has been shown to cause decay in Norway spruce (Picea abies (L.) H. Karst.), while Scots pine (Pinus sylvestris L.) can quickly heal over the branch scars. Pruning of living branches reduces the crown, the effect of which remains small if only the lowest branches are pruned. Pruning of dry branches has little effect on the health of the tree. The main objective of pruning is to improve the quality of timber. Knottiness decreases strength and appearance of timber. Pruning increases the yield of knot-free sapwood, which is especially valuable in veneer timber. Pruning is, therefore, at present most suitable for birch and aspen which are used in veneer industry. In both species pruning should be directed mainly to dry branches.

The PDF includes a summary in German.

  • Lappi-Seppälä, ORCID ID:E-mail:
article id 7302, category Article
M. Lappi-Seppälä. (1934). Karsimisesta ja sen metsänhoidollisesta merkityksestä. Acta Forestalia Fennica vol. 40 no. 25 article id 7302. https://doi.org/10.14214/aff.7302
English title: The silvicultural influences of pruning.

Pruning growing trees influences tree growth and value of the wood and yield of timber of the stand. Pruning living branches create open wounds on the stems that can risk the growth of tree species that are vulnerable to injuries. For instance, pruning has been shown to cause decay in Norway spruce (Picea abies (L.) H. Karst.), while Scots pine (Pinus sylvestris L.) can quickly heal over the branch scars. Pruning of living branches reduces the crown, the effect of which remains small if only the lowest branches are pruned. Pruning of dry branches has little effect on the health of the tree. The main objective of pruning is to improve the quality of timber. Knottiness decreases strength and appearance of timber. Pruning increases the yield of knot-free sapwood, which is especially valuable in veneer timber. Pruning is, therefore, at present most suitable for birch and aspen which are used in veneer industry. In both species pruning should be directed mainly to dry branches.

The PDF includes a summary in German.

  • Lappi-Seppälä, ORCID ID:E-mail:
article id 7296, category Article
T. Rancken. (1934). Erfarenheter om asken som skogsträd i Finland. Acta Forestalia Fennica vol. 40 no. 19 article id 7296. https://doi.org/10.14214/aff.7296
English title: Experiences of cultivation of ash as a forest tree in Finland.

Cultivation of ash (Fraxinus exelsior L.), even though it is a native species in Finland, has been hindered by the belief that it cannot produce quality timber in Finland. However, it can be concluded that the quality of ash timber is as good as that of timber imported to the country, if the trees are grown in a fertile site, the crown density is high, and the stand is tended properly. In these conditions, ash wood may have 3 mm ring width or more. Measurements made in ash stands in Turku region and in Åland show that at the best sites ash trees reach a height of 20–22 m in 70–80 years. According to the field tests made by the author, it can be concluded that ash can be successfully grown in Southern Finland in Åland, Turku region, in the coastal areas of Uusimaa and in Karelian isthmus. The species requires a fertile, moist upland forest site. The early growth is best secured by planting the seedlings under a well thinned broadleaved stand, which is then thinned every fifth year. Open lands growing grass should be avoided.

The PDF includes a Finnish and German summary.

  • Rancken, ORCID ID:E-mail:
article id 7272, category Article
Viljo O. Sierla. (1933). Uittoyhdistysten kuljettamat puumäärät vv. 1922-1927. Acta Forestalia Fennica vol. 39 no. 1 article id 7272. https://doi.org/10.14214/aff.7272
English title: Timber transportation of the floating associations in 1922¬‒1927.

 The numerous waterways have promoted the development of forest industry in Finland by offering an easy way to transport timber almost in the whole country. Floating associations arrange the floating for its members. This study, accomplished in the Forest Research Institute, compiles the statistics of the different associations in 1922­‒1927.  The volume of timber transported by the floating associations increased by 40% during the 6-year period, reaching 10.5 million m3 in 1927. The increase has been supported by the number of collectively used floating channels. The number of the floating associations increase from 17 to 26 and the length of the floating channels used by them to 8,300 km in 1922‒1927. About 70‒80% of the transported timber was logs and the 20‒30% small timber. Floated timber comprised 70-80% of the all roundwood used in the forest industry in Finland at the time. Majority of the logs were softwood.

The PDF includes a summary in German.

  • Sierla, ORCID ID:E-mail:
article id 7270, category Article
Eino Saari. (1932). Tutkimuksia Suomen sahateollisuuden raaka-ainekustannuksista. Acta Forestalia Fennica vol. 38 no. 4 article id 7270. https://doi.org/10.14214/aff.7270
English title: Studies on cost of raw materials in the Finnish sawmill industry.

The article is a review on the costs of raw materials in the Finnish sawmill industry in 1920s based on statistics collected from the members of the Central Association of the Finnish Woodworking Industries (now Finnish Forest Industries). The article includes statistics about the average size of if the saw timber bought in standing sales from private forests and harvested from the industry’s own forests, stumpage price of the timber, and labour costs of the harvesting of the wood. The average size of the logs was greater in the northern part of Finland, where the sawmills could limit the purchases of smaller timber. In the southern part of the country, the size of the timber decreased in 1922‒1926 due to growing demand of the timber. The long transport distances in the north influenced the costs. The number of logs per tree increased during the period. The level of stumpage price varied considerably in different parts of the country, falling from the south-west to the east and north. Competition of raw material increased the stumpage prices in 1922a and 1926‒27. The international economic downturn influenced the industry in 1929‒1931.

The PDF includes a summary in German.

  • Saari, ORCID ID:E-mail:
article id 7267, category Article
V. Pöntynen. (1932). Jalostamattoman puutavaran vienti Suomesta vuosina 1911-1931. Acta Forestalia Fennica vol. 38 no. 1 article id 7267. https://doi.org/10.14214/aff.7267
English title: Export of roundwood from Finland in 1911‒1931.
Original keywords: puun vienti; raakapuu; vienti; sahatukki; parru

The export of roundwood from Finland was studied based on the official statistics of foreign trade. The volumes were converted to solid volumes under bark. Roundwood (logs and masts) or raw timber trade consisted mainly of saw logs. The main tree species was Scots pine (Pinus sylvestrs L.) and Norway spruce (Picea abies (L.) H. Karst.). The annual volumes varied from 29,200 m3 in the war year 1918 to 657,200 m3 in 1924. Before the World War I the roundwood was exported mainly to Sweden and Russia, after the war the trade to Russia ceased. Also split spillet was a significant export item before the war. The export peaked in 1916 to 3 million m3, but decreased after the war to 30,000‒40,000 m3. The most important export item in the group of hewn timber has been Egyptian rafters, with annual export of 15,000‒284,600 m3 with the exception of the time of war. The export of spars exported to other countries than Egypt was highest before the war with 125,000 m3. The export of sleepers varied strongly, peaking in 1922. The total export of roundwood varied from 131,000 m3 in 1918 to 4.3 million m3 in 1927. Roundwood has mainly been exported to the European countries. Before the war, the main trading partners were United Kingdom and Russia. After the war the share of United Kingdom was nearly half of the volume, and Russia was replaced with Sweden.

The PDF includes a summary in German.

  • Pöntynen, ORCID ID:E-mail:
article id 7263, category Article
I. Lassila. (1931). Untersuchungen über den Einfluss des Waldtyps auf die Qualität der Kiefer. Acta Forestalia Fennica vol. 37 no. 1 article id 7263. https://doi.org/10.14214/aff.7263
English title: Studies on the influence of the forest type on the quality of pine.

The quality of timber is very important in trade and dependable on the purpose of the timber. The article describes the influence of the forest type on the mechanic-technical properties of the timber. The studied properties are weight, the mean breadth of the annual growth rings, and the compression strength.

The percentage of the annual growth rings that is formed during the autumn is characteristic for the compression strength, and it varies accordingly on different forest types. The result from the formula of Janka depends on the forest type.

Being able to classify the timber according its quality makes it possible to have better price for it. it is also important when deciding for what purpose the timber can be used.

The PDF contains a summary in Finnish. 

  • Lassila, ORCID ID:E-mail:
article id 7235, category Article
Andr. Teikmanis. (1929). Lettlands Wälder und Holzexport. Acta Forestalia Fennica vol. 34 no. 22 article id 7235. https://doi.org/10.14214/aff.7235
English title: Forests and timber exports of Latvia.
Original keywords: Lettland; Wald; Forstindustrie; Holzexport

After the world war one new states were built and they created their own economies and started foreign trade with different products. Timber is one of the traded articles, and not without meaning. New states, Latvia as one of them, have achieved great interest on international timber market, thanks to its favorable transport conditions.

The article presents the main characters of Latvian forests, ownership structure, and the governance related to felling and timber production. Also the most important branches of forest industry are presented. The most important aspects of the Latvian forestry are summarized in the end of article.       

The volume 34 of Acta Forestalia Fennica is a jubileum publication of professor Aimo Kaarlo Cajander.

  • Teikmanis, ORCID ID:E-mail:
article id 5632, category Article
Annikki Mäkelä, Veli-Pekka Ikonen, Petteri Vanninen. (1997). An application of process-based modelling to the development of branchiness in Scots pine. Silva Fennica vol. 31 no. 3 article id 5632. https://doi.org/10.14214/sf.a8534

A process-oriented tree and stand growth model is extended to be applicable to the analysis of timber quality, and how it is influenced by silvicultural treatments. The tree-level model is based on the carbon balance and it incorporates the dynamics of five biomass variables as well as tree height, crown base, and breast height diameter. Allocation of carbon is based on the conservation of structural relationships, in particular, the pipe model. The pipe-model relationships are extended to the whorl level, but in order to avoid a 3-dimensional model of entire crown structure, the branch module is largely stochastic and aggregated. In model construction, a top-down hierarchy is used where at each step down, the upper level sets constraints for the lower level. Some advantages of this approach are model consistency and efficiency of calculations, but probably at the cost of reduced flexibility. The detailed structure related with the branching module is preliminary and will be improved when more data becomes available. Model parameters are identified for Scots pine (Pinus sylvestris L.) in Southern Finland, and example simulations are carried out to compare the development of quality characteristics in different stocking densities.

  • Mäkelä, ORCID ID:E-mail:
  • Ikonen, ORCID ID:E-mail:
  • Vanninen, ORCID ID:E-mail:
article id 5620, category Article
Anne Toppinen. (1997). Testing for Granger-causality in the Finnish roundwood market. Silva Fennica vol. 31 no. 2 article id 5620. https://doi.org/10.14214/sf.a8521

The existence and direction of causal relationships between the time series for the Finnish roundwood market for the period 1960–1994 is tested. Using simple bivariate analysis, we found evidence that for both logs and pulpwood, the lagged prices are helpful in forecasting quantity for the next year, but not vice versa. Saw log stumpage prices have significantly Granger-caused pulpwood prices over the business cycles, but the effect has diminished towards the present time. For quantities traded, the direction of causality was rather from pulpwood to saw logs. The consistency of bivariate test results was checked by the Granger-causality tests within trivariate VAR-models for both markets, and the results were found to be fairly similar to bivariate tests. The price fluctuations in the international markets for forest products have been found to be carried to domestic wood markets dominantly via the pulpwood part of the market.

  • Toppinen, ORCID ID:E-mail:
article id 5614, category Article
Mika Jääskelä, Kari Heliövaara, Mikko Peltonen, Hannu Saarenmaa. (1997). Comparison of protection methods of pine stacks against Tomicus piniperda. Silva Fennica vol. 31 no. 2 article id 5614. https://doi.org/10.14214/sf.a8515

Three most promising protection methods of pine pulp wood stacks against the attacks of Tomicus piniperda L. were compared. The methods were the covering of stacks by fibreglass-strengthened paper or twofold achrylene netting, removing the upper parts of stacks, and enhanced planning of the placement of the timber store using ARC/INFO GIS-software. T. piniperda was observed to strongly prefer the upper parts of the stacks: 90 % of the beetles occurred within 0.5 meters of the top of the stacks. Covering of the stacks decreased the attack density of T. piniperda, and the protection effect of covering was 80 %. Due to long transport distances and fragmentation of forest landscape the relocation of timber store was found to be an unsuitable method in the practical level. Also, taking into account the costs of the method, removing of the upper parts of stacks was considered to be the optimal solution.

  • Jääskelä, ORCID ID:E-mail:
  • Heliövaara, ORCID ID:E-mail:
  • Peltonen, ORCID ID:E-mail:
  • Saarenmaa, ORCID ID:E-mail:
article id 5614, category Article
Mika Jääskelä, Kari Heliövaara, Mikko Peltonen, Hannu Saarenmaa. (1997). Comparison of protection methods of pine stacks against Tomicus piniperda. Silva Fennica vol. 31 no. 2 article id 5614. https://doi.org/10.14214/sf.a8515

Three most promising protection methods of pine pulp wood stacks against the attacks of Tomicus piniperda L. were compared. The methods were the covering of stacks by fibreglass-strengthened paper or twofold achrylene netting, removing the upper parts of stacks, and enhanced planning of the placement of the timber store using ARC/INFO GIS-software. T. piniperda was observed to strongly prefer the upper parts of the stacks: 90 % of the beetles occurred within 0.5 meters of the top of the stacks. Covering of the stacks decreased the attack density of T. piniperda, and the protection effect of covering was 80 %. Due to long transport distances and fragmentation of forest landscape the relocation of timber store was found to be an unsuitable method in the practical level. Also, taking into account the costs of the method, removing of the upper parts of stacks was considered to be the optimal solution.

  • Jääskelä, ORCID ID:E-mail:
  • Heliövaara, ORCID ID:E-mail:
  • Peltonen, ORCID ID:E-mail:
  • Saarenmaa, ORCID ID:E-mail:
article id 5614, category Article
Mika Jääskelä, Kari Heliövaara, Mikko Peltonen, Hannu Saarenmaa. (1997). Comparison of protection methods of pine stacks against Tomicus piniperda. Silva Fennica vol. 31 no. 2 article id 5614. https://doi.org/10.14214/sf.a8515

Three most promising protection methods of pine pulp wood stacks against the attacks of Tomicus piniperda L. were compared. The methods were the covering of stacks by fibreglass-strengthened paper or twofold achrylene netting, removing the upper parts of stacks, and enhanced planning of the placement of the timber store using ARC/INFO GIS-software. T. piniperda was observed to strongly prefer the upper parts of the stacks: 90 % of the beetles occurred within 0.5 meters of the top of the stacks. Covering of the stacks decreased the attack density of T. piniperda, and the protection effect of covering was 80 %. Due to long transport distances and fragmentation of forest landscape the relocation of timber store was found to be an unsuitable method in the practical level. Also, taking into account the costs of the method, removing of the upper parts of stacks was considered to be the optimal solution.

  • Jääskelä, ORCID ID:E-mail:
  • Heliövaara, ORCID ID:E-mail:
  • Peltonen, ORCID ID:E-mail:
  • Saarenmaa, ORCID ID:E-mail:
article id 5555, category Article
Mauno Pesonen, Arto Kettunen, Petri Räsänen. (1995). Modelling non-industrial private forest landowners’ strategic decision making by using logistic regression and neural networks: Case of predicting the choice of forest taxation basis. Silva Fennica vol. 29 no. 2 article id 5555. https://doi.org/10.14214/sf.a9206

In this study, logistic regression and neural networks were used to predict non-industrial private forests (NIPF) landowners’ choice of forest taxation basis. The main frame of reference of the study was the Finnish capital taxation reform of 1993. As a consequence of the reform, landowners were required to choose whether to be taxed according to site-productivity or realized-income during the coming transition period of thirteen years.

The most important factor affecting the landowners’ choice of taxation basis was the harvest rate during the transition period, i.e. the chosen timber management strategy. Furthermore, the estimated personal marginal tax rate and the intention to cut timber during next three years affected the choice. The descriptive landowner variables did not have any marked effect on the choice of forest taxation basis.

On average, logistic regression predicted 71% of the choices correctly; the corresponding figure for neural networks was 63%. In both methods, the choice of site-productivity taxation was predicted more accurately than the choice of realized-income taxation. An increase in the number of model variable did not significantly improve the results of neural networks and logistic regression.

  • Pesonen, ORCID ID:E-mail:
  • Kettunen, ORCID ID:E-mail:
  • Räsänen, ORCID ID:E-mail:
article id 5547, category Article
Tiina Tolvanen-Sikanen, Pertti Harstela, Lauri Sikanen. (1995). A game theoretic simulation model for quality oriented timber supply to sawmills. Silva Fennica vol. 29 no. 1 article id 5547. https://doi.org/10.14214/sf.a9198

The first aim of this study was to develop a simulation model describing the flow of different timber qualities to different firms. The second aim was to study preliminary the factors which affect timber distributions. In addition, we tested the hypothesis that in a small sawmill firm the traditional way of organizing timber procurement does not direct effectively good quality logs to the special production. The game theoretic approaching and the principles of Monte-Carlo simulation were applied in development of the simulation model. The most important factors of the model were tried to find for further studies with sensitive analysis. Empirical validation brought forth promising results in the area of one municipality. The buyer’s awareness of a marked stand, the seller’s willingness to sell a marked stand, the buyer’s ability to pay for wood and the proportion of first quality pine logs in a marked stand affected the distribution of pine logs. The results also supported the hypothesis that the traditional system, in which sawmills or their own forest departments procure themselves all timber needed, is not the most effective way to direct enough good quality timber to the special production.

  • Tolvanen-Sikanen, ORCID ID:E-mail:
  • Harstela, ORCID ID:E-mail:
  • Sikanen, ORCID ID:E-mail:
article id 5398, category Article
Timo Karjalainen, Seppo Kellomäki, Ari Pussinen. (1994). Role of wood-based products in absorbing atmospheric carbon. Silva Fennica vol. 28 no. 2 article id 5398. https://doi.org/10.14214/sf.a9163

The amount of carbon (C) stored in wood products manufactured in Finland was calculated with the help of a model using wood harvesting statistics, product flows and lifespans in order to study how much C could be set aside from the atmospheric C cycle outside the forest ecosystem. The calculations showed that on the average 9.9 Tg C/a was in harvested timber in 1986–1991 in Finland. C emissions of timber harvest and transport were 0.1 Tg C/a. In production processes about one third of the C bound in in timber was released into the atmosphere, but two thirds was still bound in products. After 50 and 100 years, more than 40% and 33% of the C initially in products was either in products still in use or disposed to landfills. The wood product C storage was most sensitive to landfill decay rate and to the burning of abandoned products for energy, but not to the same extent to the length of the lifespan of products.

  • Karjalainen, ORCID ID:E-mail:
  • Kellomäki, ORCID ID:E-mail:
  • Pussinen, ORCID ID:E-mail:
article id 7095, category Article
Eino Saari. (1923). Sahapuun kantohinta ja menekki Suomen valtionmetsissä vv. 1913-1922. Acta Forestalia Fennica vol. 27 no. 2 article id 7095. https://doi.org/10.14214/aff.7095
English title: The stumpage prices and demand of saw timber in state forests of Finland in 1913-1922.

The survey focuses on the stumpage prices of standing sales, where the buyer of the wood takes care of felling and transport of the timber. The study concentrates further on conifer sawn timber. The prices of the sawn timber rose continuously from 1891 to 1910. After 1913 the stumpage price fluctuations reflected the changes in the market. The article includes a detailed description on the changes of the saw timber in 1913-1922 and the factors affecting the prices. The prices are shown for different parts of the Finland. The first world war affects the prices and demand on saw timber in 1917-1918. In Northern Finland the prices of sawn timber increased slower than in Southern Finland. In general, the unfavorable factors have had stronger impact on the stumpage prices than the favorable.

The PDF includes a summary in German.

  • Saari, ORCID ID:E-mail:
article id 7095, category Article
Eino Saari. (1923). Sahapuun kantohinta ja menekki Suomen valtionmetsissä vv. 1913-1922. Acta Forestalia Fennica vol. 27 no. 2 article id 7095. https://doi.org/10.14214/aff.7095
English title: The stumpage prices and demand of saw timber in state forests of Finland in 1913-1922.

The survey focuses on the stumpage prices of standing sales, where the buyer of the wood takes care of felling and transport of the timber. The study concentrates further on conifer sawn timber. The prices of the sawn timber rose continuously from 1891 to 1910. After 1913 the stumpage price fluctuations reflected the changes in the market. The article includes a detailed description on the changes of the saw timber in 1913-1922 and the factors affecting the prices. The prices are shown for different parts of the Finland. The first world war affects the prices and demand on saw timber in 1917-1918. In Northern Finland the prices of sawn timber increased slower than in Southern Finland. In general, the unfavorable factors have had stronger impact on the stumpage prices than the favorable.

The PDF includes a summary in German.

  • Saari, ORCID ID:E-mail:
article id 5500, category Article
Mikko Kantola, Pertti Harstela. (1993). Puunhankinnan englantilaiset ja suomalaiset perustermit. Silva Fennica vol. 27 no. 1 article id 5500. https://doi.org/10.14214/sf.a15661
English title: The basic terminology of timber harvesting in Finnish and in English .

The paper discussed the definitions of different Finnish and English terms concerning timber harvesting, and suggests definitions and translations of the terms.

  • Kantola, ORCID ID:E-mail:
  • Harstela, ORCID ID:E-mail:
article id 7092, category Article
August Renvall. (1923). Beobachtungen über die Exzentrizität des lappländischen Kiefernstammes. Acta Forestalia Fennica vol. 26 no. 4 article id 7092. https://doi.org/10.14214/aff.7092
English title: Observations on the eccentricity of pine trunks in Lapland.

The hard climate and other environmental conditions cause irregularities in the growth of trees in Lapland. Those changes weaken the characteristics of the tree for industrial use and hence lowers the timber price. The eccentricity is mainly caused by the strong wind burden.

The data for the article consists of 428 increment core samples from pine trees different ages, sizes and growth rate. There were collected in years 1910-1912 in Finnish Lapland, regions Utsjoki and Inari. The increment cores were collected on the height of 1.3 meters in south-north direction straight crosswise through the whole tree. The difference of length was measured between southern and northern half rays. Earlier studies show that the eccentricity remains the same in different heights of the tree. Hence studying the variations only on the breast height radiuses is possible.

The mean eccentricity is 12.3% and its maximum varies mostly between 20 and 25%. There are no differences in eccentricity between trees of different age classes or diameter. 

  • Renvall, ORCID ID:E-mail:
article id 5490, category Article
Timo Pukkala, Jari Karsikko, Taneli Kolström. (1992). A spatial model for the diameter of thickest branch of Scots pine. Silva Fennica vol. 26 no. 4 article id 5490. https://doi.org/10.14214/sf.a15651

The model predicts the base diameter of the thickest living branch of a tree growing in a planted or naturally regenerated even-aged stand. A mixed model type was used in which the residual variation was divided into within-stand and between-stand components. The study material consisted of 779 trees measured in 12 plots located in 20 to 35 years old Scots pine (Pinus sylvestris L.) stands (breast height age 10 to 20 years). Branch diameter was closely connected to the breast height diameter of the stem. In a stand of a certain age, competition by close neighbours slightly decreased branch diameter in a given diameter class. According to the model, the greatest difference is between trees subjected to very little competition and those subjected to normal competition. The model was used in simulated stands with varying age, density, and tree arrangement. The simulations showed that trees with rapid diameter growth at young age had thicker branches at a given breast height diameter than trees with slower diameter growth. However, a very slow growth rate did not produce trees with branches thinner than those possessing a medium growth rate.
The PDF includes an abstract in Finnish.

  • Pukkala, ORCID ID:E-mail:
  • Karsikko, ORCID ID:E-mail:
  • Kolström, ORCID ID:E-mail:
article id 5469, category Article
Risto Heikkilä, Kari Löyttyniemi. (1992). Growth response of young Scots pines to artificial shoot breaking simulating moose damage. Silva Fennica vol. 26 no. 1 article id 5469. https://doi.org/10.14214/sf.a15627

The main stem of young Scots pine (Pinus sylvestris L.) trees was cut off halfway along the current leading shoot and the two previous years’ leading shoots to simulate moose (Alces alces) damage. Trees of the same size were chosen as controls before treatments. The experiment was inspected ten years after artificial stem breakage. Removing the current leading shoot and the second shoot did not essentially affect the height and diameter growth of the trees. Removal down to the third shoot reduced the height as well as diameter growth. The average loss in growth was equivalent to less than one year’s growth. When the stem was cut off at the second or third shoot, stem crookedness and the presence of knots resulted in stem defects that will subsequently reduce the sawtimber quality. A high proportion of the stem defects will obviously still be visible at the first thinning cutting. Removing injured trees as pulpwood and pruning the remaining parts of cut stems evidently improves the quality of pine stand with moose damage.

The PDF includes an abstract in Finnish.

  • Heikkilä, ORCID ID:E-mail:
  • Löyttyniemi, ORCID ID:E-mail:
article id 5450, category Article
Bo Långström, Claes Hellqvist. (1991). Shoot damage and growth losses following three years of Tomicus-attacks in Scots pine stands close to a timber storage site. Silva Fennica vol. 25 no. 3 article id 5450. https://doi.org/10.14214/sf.a15604

Shoot losses due to maturation feeding by pine shoot beetles (Tomicus piniperda (L.) and T. minor (Hart.), Col., Scolytidae) and subsequent growth losses were studied in Scots pine (Pinus sylvestris L.) stands growing at different distances from a timber yard, where pine timber was stored during the years 1982–84. In autumn 1985, pine trees were felled at 20, 40, 80, 500 and 1,500 m distance from the timber yard, five trees in each distance class. Trees were analysed for beetle attack, needle biomass and growth. In autumn 1988, increment cores were taken from 20 trees in each distance class.

In 1985, different damage estimates showed that beetle damage was more than 10-fold in the crowns of pine trees growing close to the timber yard as compared to less damaged trees in greater distance. Crude needle biomass estimates indicated that the trees attacked most had lost more than half of the total foliage. Following three years of attack, basal area growth decreased for 2–3 years and recovered during the subsequent 3 years, the total period of loss thus being 5–6 years. The loss in volume growth during 1983–85 was ca. 70, 40, 20 and 10% at 20, 40, 80 and 500 m distance from the beetle source, respectively, compared to the stand at 1,500. Growth losses did not occur until the number of beetle-attacks, ”pegs”, exceeded ca. 200 per tree. The highest observed growth losses occurred in trees with more than 1,000 pegs per tree.

The PDF includes an abstract in Finnish

  • Långström, ORCID ID:E-mail:
  • Hellqvist, ORCID ID:E-mail:
article id 7077, category Article
Aimo Kaarlo Cajander. (1923). Über das Verhältnis zwischen Waldzuwachs und Holzverbrauch in Finnland. Acta Forestalia Fennica vol. 25 no. 2 article id 7077. https://doi.org/10.14214/aff.7077
English title: On the relation between forest growth and timber consumption in Finland.

The article is a presentation given by the author on occasion of visit from Austrian timber industry and foresters (August 17th 1923), and again for the German visitors (August 20th 1923) in Punkaharju, Finland. The speech deals with the question of the overuse of Finnish forest compared to their growth. The developments of slash-and-burn-culture and forest inventories are described. The results of the inventories show, though still in preliminary state, that there is no nationwide overuse in total, though there are some locations where the felling are bigger than growth. 

  • Cajander, ORCID ID:E-mail:
article id 5431, category Article
Juha Siitonen. (1990). Potential forest pest beetles conveyed to Finland on timber imported from the Soviet Union. Silva Fennica vol. 24 no. 3 article id 5431. https://doi.org/10.14214/sf.a15585

Coniferous timber imported by rail from the Soviet Union in Finland was studied for the presence of potential forest and timber pest beetles. Systematic samples of fourteen lots of pine pulpwood were examined. Seven of the lots originated from the European parts of the Soviet Union and seven from Siberia. 23 species of Scolytidae and about 18 other phloeophagous species were found including three species new for Finland: Phaenops guttulata (Buprestidae), Ips subelongatus and Orthotomicus erosus (Scolytidae).

The PDF includes an abstract in Finnish.

  • Siitonen, ORCID ID:E-mail:
article id 5431, category Article
Juha Siitonen. (1990). Potential forest pest beetles conveyed to Finland on timber imported from the Soviet Union. Silva Fennica vol. 24 no. 3 article id 5431. https://doi.org/10.14214/sf.a15585

Coniferous timber imported by rail from the Soviet Union in Finland was studied for the presence of potential forest and timber pest beetles. Systematic samples of fourteen lots of pine pulpwood were examined. Seven of the lots originated from the European parts of the Soviet Union and seven from Siberia. 23 species of Scolytidae and about 18 other phloeophagous species were found including three species new for Finland: Phaenops guttulata (Buprestidae), Ips subelongatus and Orthotomicus erosus (Scolytidae).

The PDF includes an abstract in Finnish.

  • Siitonen, ORCID ID:E-mail:
article id 5419, category Article
Timo Pukkala, Owen Mubita, Jussi Saramäki. (1990). Management planning system for tree plantations. Silva Fennica vol. 24 no. 2 article id 5419. https://doi.org/10.14214/sf.a15573

The paper presents a simple model of long-term forest management planning in tree plantations. The model is particularly suitable for developing countries where the research resources are limited. The management plan is prepared in two steps. First, one or several treatment schedules are simulated for each calculation unit (age class, compartment, etc.) over the selected planning period. Second, an optimal combination treatment schedules according to the selected objectives and constraints is searched by mathematical programming. The simulation of growth is based on the prediction of the diameter distribution at the desired time point. All stand characteristics are derived from this distribution. The models needed in the yield simulation can be estimated from temporary sample plots. A case study management plan for 13,000 ha of Pinus kesiya (Royle ex Gordon) plantations in Zambia is presented to demonstrate the system.

The PDF includes an abstract in Finnish.

  • Pukkala, ORCID ID:E-mail:
  • Mubita, ORCID ID:E-mail:
  • Saramäki, ORCID ID:E-mail:
article id 5315, category Article
Seppo Kellomäki, Matti Seppälä. (1987). Simulations on the effects of timber harvesting and forest management on the nutrient cycle and productivity of Scots pine stands. Silva Fennica vol. 21 no. 2 article id 5315. https://doi.org/10.14214/sf.a15472

Effects of varying rotation, thinning, fertilization and harvest intensity on the productivity and nitrogen cycle of Scots pine (Pinus sylvestris L.) stand were studied on the basis of computer simulation. The increasing intensity of management increased the loss of nitrogen in the cycle. Short rotation, associated with early thinning by means of the whole tree harvest, proved to be especially detrimental regarding the productivity of the forest ecosystem. Fertilization associated with thinnings is of great importance in maintaining the productivity of a forest ecosystem during an intensive timber harvest.

The PDF includes an abstract in Finnish.

  • Kellomäki, ORCID ID:E-mail:
  • Seppälä, ORCID ID:E-mail:
article id 5314, category Article
M. Saarilahti, E. Bakena, G. Mboya, T. Minja, T. Ngerageze, J. Ntahompagaze. (1987). Studies on Tanzanian forest work. Silva Fennica vol. 21 no. 2 article id 5314. https://doi.org/10.14214/sf.a15471

Four teams of two workers were time-studied in clearcutting of a cypress plantation and three teams in sulky skidding. The heart rate was recorded every 30 s. The average heartrate in timber cutting was 117.5 ± 13.4 P/min, and it was mainly dependent on worker’s working capacity. Average work load index was 41 ± 3% when working at 97% performance. The production rate was then 2.5 m3/h (crew). In sulky skidding the heart rate was lower, 106 ± 1.1 P/min, as well as the work load (WLI 30 ± 1%) and performance rating (87%). The low production rate (1.1 m3/h) (crew)) over 45 m distance is mainly due to under-dimensioned load size. The energy expenditure in timber cutting was 21.4 kJ/min and in sulky skidding 16.3 kJ/min. Daily energy expenditure was 15.0 MJ/d, and most of the timber cutters belonged to the class ”exceptionally active”.

The PDF includes an abstract in Finnish.

  • Saarilahti, ORCID ID:E-mail:
  • Bakena, ORCID ID:E-mail:
  • Mboya, ORCID ID:E-mail:
  • Minja, ORCID ID:E-mail:
  • Ngerageze, ORCID ID:E-mail:
  • Ntahompagaze, ORCID ID:E-mail:
article id 5295, category Article
J. E. de Steiguer, J. P. Royer. (1986). Increasing forestry investments by means of public policy programs. Silva Fennica vol. 20 no. 4 article id 5295. https://doi.org/10.14214/sf.a27751

In 1979, the Federal Research in the United States instituted a so-called ”tight money” policy which led to a decrease in the demand for stumpage. The decrease in demand brought about lower stumpage prices and, consequently, a waning interest in policies to stimulate NIPF production. The authors report on five recent studies on NIPF behaviour and raise concerns that increases in demand for housing may bring new pressure upon NIPF as a source of wood.

  • Steiguer, ORCID ID:E-mail:
  • Royer, ORCID ID:E-mail:
article id 5295, category Article
J. E. de Steiguer, J. P. Royer. (1986). Increasing forestry investments by means of public policy programs. Silva Fennica vol. 20 no. 4 article id 5295. https://doi.org/10.14214/sf.a27751

In 1979, the Federal Research in the United States instituted a so-called ”tight money” policy which led to a decrease in the demand for stumpage. The decrease in demand brought about lower stumpage prices and, consequently, a waning interest in policies to stimulate NIPF production. The authors report on five recent studies on NIPF behaviour and raise concerns that increases in demand for housing may bring new pressure upon NIPF as a source of wood.

  • Steiguer, ORCID ID:E-mail:
  • Royer, ORCID ID:E-mail:
article id 5295, category Article
J. E. de Steiguer, J. P. Royer. (1986). Increasing forestry investments by means of public policy programs. Silva Fennica vol. 20 no. 4 article id 5295. https://doi.org/10.14214/sf.a27751

In 1979, the Federal Research in the United States instituted a so-called ”tight money” policy which led to a decrease in the demand for stumpage. The decrease in demand brought about lower stumpage prices and, consequently, a waning interest in policies to stimulate NIPF production. The authors report on five recent studies on NIPF behaviour and raise concerns that increases in demand for housing may bring new pressure upon NIPF as a source of wood.

  • Steiguer, ORCID ID:E-mail:
  • Royer, ORCID ID:E-mail:
article id 5293, category Article
Claude Gendreau. (1986). Historical considerations and evolution of the forest policies for small woodlot owners of Quebec. Silva Fennica vol. 20 no. 4 article id 5293. https://doi.org/10.14214/sf.a27749

In order to understand the present forest policies for the small woodlot of Quebec, it is essential to understand the history of settlement of Quebec. Following this brief description, the author introduces the various forest policies (programs) which have been initiated in Quebec by various levels of governments in order to deal with the management of these lands.

  • Gendreau, ORCID ID:E-mail:
article id 5292, category Article
Ryoichi Handa. (1986). On the principles of Japanese forest policy since 1950. Silva Fennica vol. 20 no. 4 article id 5292. https://doi.org/10.14214/sf.a27748

In Japan many governmental projects have been promoted during 35 years since 1950, which were most active in the history of our forestry and wood industry. They were pushed forward for and by high economic growth. This article refers to the development of our forest policy and projects in those days. But as for the future of the forest economics, it is an urgent question to develop the comparative study between every nation’s experience. In order to contribute to this problem, the forest policy is divided into three fields and experiences are discussed.

  • Handa, ORCID ID:E-mail:
article id 5292, category Article
Ryoichi Handa. (1986). On the principles of Japanese forest policy since 1950. Silva Fennica vol. 20 no. 4 article id 5292. https://doi.org/10.14214/sf.a27748

In Japan many governmental projects have been promoted during 35 years since 1950, which were most active in the history of our forestry and wood industry. They were pushed forward for and by high economic growth. This article refers to the development of our forest policy and projects in those days. But as for the future of the forest economics, it is an urgent question to develop the comparative study between every nation’s experience. In order to contribute to this problem, the forest policy is divided into three fields and experiences are discussed.

  • Handa, ORCID ID:E-mail:
article id 5291, category Article
David J. Brooks. (1986). Evaluating the regional and distributional impacts of forestry cost-share payments. Silva Fennica vol. 20 no. 4 article id 5291. https://doi.org/10.14214/sf.a27747

Standard methods of welfare economics are used in a market simulating framework to evaluate policy measures designed to increase future timber supplies. Forest management cost-share programs are examined using this methodology. The differential regional impact of cost-share payments is considered, as is the distribution of these benefits between stumpage producers (owners of forest land) and stumpage consumers (producers of forest products). Previous estimates of the welfare gains that would result from a higher level of forest management cost-share payments in the southern United States are revised to account for the loss of public revenue resulting from lower future prices. A methodology for comparing alternative policy instruments is discussed, and a preliminary, qualitative comparison is made between the use of cost-share payments and alternative policy measures.

  • Brooks, ORCID ID:E-mail:
article id 5291, category Article
David J. Brooks. (1986). Evaluating the regional and distributional impacts of forestry cost-share payments. Silva Fennica vol. 20 no. 4 article id 5291. https://doi.org/10.14214/sf.a27747

Standard methods of welfare economics are used in a market simulating framework to evaluate policy measures designed to increase future timber supplies. Forest management cost-share programs are examined using this methodology. The differential regional impact of cost-share payments is considered, as is the distribution of these benefits between stumpage producers (owners of forest land) and stumpage consumers (producers of forest products). Previous estimates of the welfare gains that would result from a higher level of forest management cost-share payments in the southern United States are revised to account for the loss of public revenue resulting from lower future prices. A methodology for comparing alternative policy instruments is discussed, and a preliminary, qualitative comparison is made between the use of cost-share payments and alternative policy measures.

  • Brooks, ORCID ID:E-mail:
article id 5290, category Article
Veli-Pekka Järveläinen. (1986). Effects of forestry extension on the use of allowable cut in non-industrial private forests. Silva Fennica vol. 20 no. 4 article id 5290. https://doi.org/10.14214/sf.a27746

An empirical analysis of the Finnish non-industrial private forest owners indicates that forestry extension has an effect on the supply of timber and the use of cutting potentials. This effect appears to be indirect rather than direct. The use of extension services is likely to increase the frequency of timber sales, which in turn, increases the use of the allowable cut via increased volume of actual cuttings. Forestry extension can also be considered as an intermediate variable through which certain background conditions and owner characteristics affect the use of cutting potential.

  • Järveläinen, ORCID ID:E-mail:
article id 5288, category Article
Christopher D. Risbrudt. (1986). Policy evaluations for U.S. federal timber sale accounting system development. Silva Fennica vol. 20 no. 4 article id 5288. https://doi.org/10.14214/sf.a27744

Development of timber sale accounting system for the U.S. Department of Agriculture, Forest Service ordered by the U.S. Congress, has entailed numerous evaluations and research projects. Critics of the current process claims administrative costs are not recovered by the prices paid for Federal timber. However, management of multiple resources for multiple uses makes traditional accounting difficult; i.e., keeping track of cash flows. A further complication involves allocating costs to the various resources (joint cost allocation), for which no nonarbitrary method currently exists. A concurrent issue involves the building of roads for timber harvest into areas released from wilderness consideration. Environmentalists see the road building program of the Federal land management agencies as an additional reason Federal management costs are not recovered from timber-generated revenues. The heart of the issue is which lands are economically suited for timber management, and what nonmarket benefits and costs accrue from the timber management.

  • Risbrudt, ORCID ID:E-mail:
article id 5288, category Article
Christopher D. Risbrudt. (1986). Policy evaluations for U.S. federal timber sale accounting system development. Silva Fennica vol. 20 no. 4 article id 5288. https://doi.org/10.14214/sf.a27744

Development of timber sale accounting system for the U.S. Department of Agriculture, Forest Service ordered by the U.S. Congress, has entailed numerous evaluations and research projects. Critics of the current process claims administrative costs are not recovered by the prices paid for Federal timber. However, management of multiple resources for multiple uses makes traditional accounting difficult; i.e., keeping track of cash flows. A further complication involves allocating costs to the various resources (joint cost allocation), for which no nonarbitrary method currently exists. A concurrent issue involves the building of roads for timber harvest into areas released from wilderness consideration. Environmentalists see the road building program of the Federal land management agencies as an additional reason Federal management costs are not recovered from timber-generated revenues. The heart of the issue is which lands are economically suited for timber management, and what nonmarket benefits and costs accrue from the timber management.

  • Risbrudt, ORCID ID:E-mail:
article id 5266, category Article
Matti Kärkkäinen. (1986). Malli männyn, kuusen ja koivun puuaineen oksaisuudesta. Silva Fennica vol. 20 no. 2 article id 5266. https://doi.org/10.14214/sf.a15445
English title: Model of knottiness of wood material in pine, spruce and birch.

A computer model was developed for predicting knottiness of wood material of Scots pine (Pinus sylvestris L.), Norway spruce (Picea abies (L.) H. Karst.) and birch (Betula sp). The prediction included location of knots, their size and quality, i.e. if they are dead or living knots. The model suits best for tree species where branches are born at the base of shoots, in Finland such tree species is Scots pine.

The usefulness of the model was tested in the prediction of knots in wooden elements of joinery industry. According to the results, the shape of cross section affects the surface quality of elements. Especially useful is a quadratic cross section as it increases the probability to get a knotless surface.

The PDF includes an abstract in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 5260, category Article
The Forest 2000 Programme sub-commitee. (1986). The Forest 2000 Programme in Finland. Silva Fennica vol. 20 no. 1 article id 5260. https://doi.org/10.14214/sf.a15439

The Forest 2000 Programme is a long-term programme for forestry and the forest industries in Finland. It attempts to obtain a better integration of timber production and other forms of forest use. The total annual cut is to be increased by 15 million m3 by the year 2010. This is almost one third greater than the level during the first few years of the 1980’s. In order to achieve the cutting targets, the cut area will have to be increased by almost one third by the turn of the century. The area of thinnings will experience the greatest increase. Considerable changes are proposed in silvicultural and basic improvement work. According to the programme, the growth of the raw-material base and the consumption of the wood-based products will permit an annual increase of about 3% in the production of the forest industries as a whole until the end of the century. This would be the same as the target growth rate of the GNP.

The PDF includes an abstract in Finnish.

  • The Forest 2000 Programme sub-commitee, ORCID ID:E-mail:
article id 5251, category Article
Markku Halinen. (1985). Männyn nuoruusvaiheen kasvunopeuden vaikutus sahatavaran laatuun. Silva Fennica vol. 19 no. 4 article id 5251. https://doi.org/10.14214/sf.a15430
English title: The effect of the growth rate of young Scots pine on the quality of sawn goods.

Totally 653 battens and planks sawn from butt logsof Scots pine (Pinus sylvestris L.) were chosen from 3 saw mills. The sawn goods were sorted according to normal sorting principles. In order to determine growth rate in the youth, the mean value of the average ring width was measured at the butt end at various distances from the pith.

The average ring width increased as the quality of the sawn goods decreased. The difference between the quality classes in ring width was measured between 2 and 4 cm from the pith. As the size of sawn goods, and, simultaneously, the log size increased, the average ring width increased in a given quality class. Research reinforced previous results, in which slow diameter growth of young Scots pines has been shown to reflect the good quality of sawn goods.

The PDF includes a summary in English.

  • Halinen, ORCID ID:E-mail:
article id 5250, category Article
P. A. Harou. (1985). Comparison of methodologies to evaluate aid programs to nonindustrial private forests. Silva Fennica vol. 19 no. 4 article id 5250. https://doi.org/10.14214/sf.a15429

A methodology to evaluate forestry programs aimed at increasing timber supply from nonindustrial private forests is presented that aggregates the marginal social cost and marginal social benefit of a sample program participants and compares them in a benefit-cost efficiency ratio. The paper exposes a methodology followed to evaluate several forestry programs in Massachusetts, USA, and discusses its advantages and inconveniences compared to the other methodologies that have been used for the same purpose. The marginal analysis is based on detailed property and landowner behaviour surveys which are costly but represent a good standard to compare the performance of other approaches. 

The PDF includes a summary in Finnish.

  • Harou, ORCID ID:E-mail:
article id 7060, category Article
August Renvall, Aarne Boman. (1921). Tilastollisia tutkimuksia yhtiöiden maanomistuksesta Suomessa III. Acta Forestalia Fennica vol. 19 no. 3 article id 7060. https://doi.org/10.14214/aff.7060
English title: Statistical studies on the landholdings of companies in Finland.

The timber companies began acquiring forest land in 1890s which raised concerns about decrease of the number of private farms and agricultural land, as had happened in Sweden earlier. This was not considered to be a major problem in Finland, but the sale of homesteads on former state lands for sawmill companies was considered to be against their objective. One reason for the sale of farms was the farmers’ poor conception of the value of the land. In 1915 three decrees that restricted the right of companies that use timber to buy land were approved. The article discusses in detail the arguments that led to the legislation and compares it to the situation in Sweden.

A survey was commissioned to study the of landholdings of the companies, and to compare it with farming in private and company owned farms. The article includes a study about individual farms in the municipalities of Multia, Heinävesi, Sulkava, Ruokolahti and Luumäki, and about land use in the areas.

The PDF includes a summary in German.

  • Renvall, ORCID ID:E-mail:
  • Boman, ORCID ID:E-mail:
article id 7060, category Article
August Renvall, Aarne Boman. (1921). Tilastollisia tutkimuksia yhtiöiden maanomistuksesta Suomessa III. Acta Forestalia Fennica vol. 19 no. 3 article id 7060. https://doi.org/10.14214/aff.7060
English title: Statistical studies on the landholdings of companies in Finland.

The timber companies began acquiring forest land in 1890s which raised concerns about decrease of the number of private farms and agricultural land, as had happened in Sweden earlier. This was not considered to be a major problem in Finland, but the sale of homesteads on former state lands for sawmill companies was considered to be against their objective. One reason for the sale of farms was the farmers’ poor conception of the value of the land. In 1915 three decrees that restricted the right of companies that use timber to buy land were approved. The article discusses in detail the arguments that led to the legislation and compares it to the situation in Sweden.

A survey was commissioned to study the of landholdings of the companies, and to compare it with farming in private and company owned farms. The article includes a study about individual farms in the municipalities of Multia, Heinävesi, Sulkava, Ruokolahti and Luumäki, and about land use in the areas.

The PDF includes a summary in German.

  • Renvall, ORCID ID:E-mail:
  • Boman, ORCID ID:E-mail:
article id 5244, category Article
Juha Lappi, Markku Siitonen. (1985). A utility model for timber production based on different interest rates for loans and savings. Silva Fennica vol. 19 no. 3 article id 5244. https://doi.org/10.14214/sf.a15423

The paper discusses the evaluation of timber production policies with different income (timber drain) schedules. Special attention is given to the temporal smoothness of the income flow. A utility model is formulated in which the objective is to maximize a fixed consumption pattern, and money can be saved and borrowed at different interest rates. We thus have smoothness requirements only for consumption, the capital market then determines the smoothness of the optimal income flow. Present discounted value and maximization of even income flow criteria are special cases of the utility model. Consumption can be maximized by linear programming. A sample problem is presented.

The PDF includes a summary in Finnish.

  • Lappi, ORCID ID:E-mail:
  • Siitonen, ORCID ID:E-mail:
article id 5202, category Article
Kari Löyttyniemi. (1983). Flight periods of some birch timber insects. Silva Fennica vol. 17 no. 4 article id 5202. https://doi.org/10.14214/sf.a15185

Flight periods of insects breeding on birch (Betula sp.) timber were observed by means of window flight traps baited with freshly cut birch logs in five locations in Finland from 1972 to 1976. Only few species were caught during the study. In general, these species were on the wing during midsummer, although flight periods of some of them were relatively long. Scolytus ratzeburgi Jans. caused harmful staining of wood within a month from attack, but the damage by the wood-boring pests remained negligible throughout the first storage summer.

The PDF includes a summary in Finnish.

  • Löyttyniemi, ORCID ID:E-mail:
article id 5179, category Article
Pertti Harstela, Antti Maukkonen. (1983). Tavanomainen ja kuormainprosessori varttuneissa harvennusmetsiköissä. Silva Fennica vol. 17 no. 2 article id 5179. https://doi.org/10.14214/sf.a15095
English title: A conventional and grapple loader processor in second and third thinnings. A simulator experiment.

Using literature and a simulator experiment, an ordinary processor and a grapple loader processor were compared in conditions corresponding to thinning later than the first commercial thinning. Visual bucking only was employed in the simulator experiment. The strip road spacing was 30 m and there was no preliminary skidding of the trees. The simulator experiment confirmed the view reached in the literature that work productivity of the grappler loader processor is 20–40 % greater than that of an ordinary processor provided that the stem size is under 0.2–0.4 m3.

The PDF includes a summary in English.

  • Harstela, ORCID ID:E-mail:
  • Maukkonen, ORCID ID:E-mail:
article id 5177, category Article
Kari Löyttyniemi. (1983). Preliminary testing of the resistance of Finnish softwood timbers to Macrotermitinae termites. Silva Fennica vol. 17 no. 1 article id 5177. https://doi.org/10.14214/sf.a15092

The resistance of Finnish softwood timbers to Macrotermitinae termites was tentatively tested under tropical conditions in Zambia using a field microtest method. Picea abies (L.) H. Karst. and Larix sibirica L. sapwood and heartwood, as well as Pinus sylvestris L. sapwood, and the sapwood of the locally grown Pinus kesiya, exhibited no natural termite resistance. On the other hand, Juniperus communis heartwood appeared to be virtually immune and the heartwood of P. Sylvestris had some resistance. There were also some differences in the resistance of the heartwood of the different P. Sylvestris individuals tested, which was correlated with the width of the annual rings in the wood samples. The termite species involved were Microtermes sp. and Odontotermes sp. The possibilities of using different types of Finnish softwood timber in the regions in the tropics where there is a risk of termite damage is discussed.

The PDF includes a summary in Finnish.

  • Löyttyniemi, ORCID ID:E-mail:
article id 5165, category Article
Päiviö Riihinen. (1982). Roundwood market: A source of stagnation of the forest industries. Silva Fennica vol. 16 no. 4 article id 5165. https://doi.org/10.14214/sf.a15080

Certain trends in the sales behaviour of private non-industrial forest owners suggest that the forest industries have to rely on a raw material supply much less than the allowable cut. This paper deals with several factors responsible for the change in sales behaviour during the last 20–25 years. These changes are caused by social change, a multi-face process which is led by industrialization. It is manifested in the increasing division of labour, more pronounced strive for efficiency, change in social values for the benefit of the adoption of innovations and thus of further changes.

It has become more common than previously to borrow money instead of selling timber. An incentive for doing so is provided by the increased progression of income tax scales which makes it more profitable than earlier to substitute a loan for timber sales with a view to reduce the amount of taxes. In 1977, the real value of the farmers’ debts was 1.7 times as large as in 1970. Inflation provides a further incentive to borrow money rather than to sell timber, because it tends to reduce debts, whereas a growing stock keeps increasing without affecting the property taxation, maintaining its real unit value.

Certain forestry policy measures conductive to increasing the forest owner’s willingness to sell timber are suggested. Among the most promising seems to be an adjustment of the present area-based yield taxation so as to take into account the age class distribution of the growing stock.

The PDF includes a summary in Finnish.

  • Riihinen, ORCID ID:E-mail:
article id 5162, category Article
Jarmo Eronen. (1982). Soviet pulp and paper industry: Factors affecting its areal expansion. Silva Fennica vol. 16 no. 3 article id 5162. https://doi.org/10.14214/sf.a15077

Planners of the Soviet pulp and paper industry are constantly faced with the problem: which investment policy guarantees the best location structure? Should one invest in existing localities or expand to new areas, especially in heavily forested parts of Siberia? A location theory for the pulp and paper industry, based on three factors (markets, wood raw materials, relative costs) has been suggested by the Soviet authors Antonov and Trusova. In the present study the theory is – for the first time – given empirical contents and the feasible areas for future growth of the industry are tentatively determined. One of the main findings of the study is the detecting of considerable unutilized wood reserves in the European USSR. This supports those Soviet views advocating a European-oriented location in investment strategy for the industry, as market and cost factors are unfavourable to Siberian location.

The PDF includes a summary in Finnish.

  • Eronen, ORCID ID:E-mail:
article id 5130, category Article
Martti Saarilahti. (1981). Mikroaaltotutka jään paksuuden mittaukseen. Silva Fennica vol. 15 no. 4 article id 5130. https://doi.org/10.14214/sf.a15187
English title: Radar measurement of ice thickness on ice roads and landing.

Light and economic FM-CW radar has been developed for controlling the bearing capacity of ice roads and landings on ice used for timber transportation and storage of timber in Finland. It was tested on natural ice and ice roads of three lakes in Southern Finland and one location on sea on the southren coast of Finland (a total of 166 observations). Ice thickness varied from 0 to 100 cm. Correlation coefficient between auger and radar measured ice thickness was r=0.99 and absolute error varied from -10 to +7 cm. The quality of ice had no influence, but by improving the interpretation of results, also the quality factors might be detected.

The PDF includes a summary in Finnish.

  • Saarilahti, ORCID ID:E-mail:
article id 5126, category Article
Martti Saarilahti. (1981). Koneiden uppoaminen suometsien puunkorjuussa. Silva Fennica vol. 15 no. 3 article id 5126. https://doi.org/10.14214/sf.a15067
English title: Sinkage of forest machines during harvesting operations on peatlands.

Questionnaires were sent out to determine the volume of wood harvested from peatlands during 1978 and the harvesting problems encountered. In total there were 110 responses which accounted for 8 million m3 of wood harvested, of which 1.0 million m3 (14%) was harvested from peatlands. The largest proportion of wood harvested from peatlands was during the winter. Most of the respondents reportet that they wait for the soil frost to set before harvesting is started on peatlands. Respondents indicated a total of 263 machines bogging down in to the soil or, for 1978, a total for Finland of 750 to 1,000 machines.
The PDF includes a summary in English.

The PDF includes a summary in English.

  • Saarilahti, ORCID ID:E-mail:
article id 5112, category Article
Timo Kyttälä. (1981). Yhteistoiminnan kehittäminen puunkorjuuorganisaatiossa työmaatapaamisen avulla. Silva Fennica vol. 15 no. 2 article id 5112. https://doi.org/10.14214/sf.a15053
English title: Development of cooperation between workers and supervisors in logging through work-site meetings.

The aim of the study was to find out the effect of the working place meetings on the increased cooperation between workers and supervisors, the improved work performance, the intensified use of machines and the improved job satisfaction. In the study loggers, forest machine operators and forement were interviewed. The results showed that the working place meeting is a useful means to realise the above-mentioned aims.

The PDF includes a summary in English.

  • Kyttälä, ORCID ID:E-mail:
article id 5101, category Article
Ilpo Tikkanen. (1981). Effects of public forest policy in Finland. Silva Fennica vol. 15 no. 1 article id 5101. https://doi.org/10.14214/sf.a15042

The purpose of the present study is to explore the applicability of some methodological approaches to empirical policy analysis in evaluating the effectiveness of public forest policy. From the perspective of effectiveness analysis we can distinguish in forest policy, aiming at the promotion of timber production, two principal objective levels in forestry: the quantity of silvicultural investments and their allocation and the quantity (sufficiency) together with the structure of timber supply. This paper is restricted to the exploration of the effect of forest policy measures directed to silvicultural investments in private forestry. First, the effects of state subsidies in silvicultural investments are analysed. The analysis is macro analysis of quantitative forest policy means, in which aggregated time series data are used as study material. Second, an attempt is made to provide a causal interpretation of the impacts of qualitative forest policy means at the woodlot level. This micro analysis utilizes an approach characteristic to the behavioural sciences.

It is concluded that like quantitative forest policy means the qualitative means, coupled with the activities of the forest promotion organizations, play a significant role in attaining the timber production goals. Of these, the professional advice given by forestry experts, has a direct effect on silvicultural activities. Extension and training activities have an indirect effect by increasing the willingness of forest owners to employ experts on their woodlots.

  • Tikkanen, ORCID ID:E-mail:
article id 5089, category Article
Seppo Kellomäki. (1980). Alustavia mittaustuloksia kuivauksen ja liotuksen vaikutuksesta kuorellisen mänty- ja kuusipuutavaran kuoren paksuuteen. Silva Fennica vol. 14 no. 4 article id 5089. https://doi.org/10.14214/sf.a15030
English title: Preliminary results of the effect of drying and soaking of the bark thickness of Scots pine and Norway spruce.

On the basis of a limited material, the drying of Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) H. Karst.) timber at room temperature decreased the thickness of the bark proportionally to the decrease in the moisture content. The decrease was the greatest in the middle portion of the trunk. In the spruce material, the decrease in bark thickness was exceeded by the shrinkage of the wood. During soaking, the bark thickness of both tree species decreased, too, contrary to the presupposed hypothesis. In both cases, the shrinkage was the greatest in the middle portion of the trunk. In the spruce material, the decrease in bark thickness was exceeded by the shrinkage of the wood. Possible explanation for the phenomenon is discussed.

The PDF includes a summary in English.

  • Kellomäki, ORCID ID:E-mail:
article id 5059, category Article
Pertti Harstela. (1980). Jäljelle jäävä puusto ja ajouralta toimivat harvennuspuun korjuukoneet. Silva Fennica vol. 14 no. 1 article id 5059. https://doi.org/10.14214/sf.a15000
English title: Remaining trees and machines working from the strip roads in thinning.

In the first part of the study the hindrance of the remaining trees when felling trees by machines working from the strip road in selective thinning was studied on the basis of the literature. In the second part there was geometrically studied the need of schematic thinning in some type stands when bundles are pre-skidded straight-lined to the strip road. In average only 0-1 trees per pre-skidding trail needs to be removed. It was concluded that trees removed from the pre-skidding trail do not significantly increase the need of schematic thinning. Remaining trees do not limit the length of machine booms if the pre-skidding trails are planned during the felling.

The PDF includes a summary in English.

  • Harstela, ORCID ID:E-mail:
article id 5051, category Article
Aili Tuimala. (1979). Kuusen lahon aiheuttamista puutavaralajisiirtymistä ja kantohintamenetyksistä. Silva Fennica vol. 13 no. 4 article id 5051. https://doi.org/10.14214/sf.a14908
English title: Changes in timber assortments and loss in stumpage prices caused by decay in growing Norway spruce timber.

Material for this study was collected from 26 stands marked for clear cutting in Southern Finland. The volume of decayed Norway spruce (Picea abies (L.) H. Karst.) timber and pulpwood was determined by deducting the volumes of these assortments (as recorded on the measurement certificate) from the volume of the standing trees. To obtain the economic loss, the volume of decayed wood was multiplied by the difference in stumpage prices between spruce timber of pulpwood and pine pulpwood. In the 17 stands of Buyer A the loss in timber volume caused by decay was 5.84% and the loss in stumpage price 2.84 Fmk/m3 (means weighted by volume). The corresponding figures in the 9 stands of Buyer B were 10.87% and 5.50 Fmk/m3, respectively.

At the mean stumpage price level for the felling season 1977-78 the losses in the stands m.f.c. mentioned above were 2.87% per unit price in the stands of Buyer A and 5.75% in the stands of Buyer B.

The PDF includes a summary in English.

  • Tuimala, ORCID ID:E-mail:
article id 5051, category Article
Aili Tuimala. (1979). Kuusen lahon aiheuttamista puutavaralajisiirtymistä ja kantohintamenetyksistä. Silva Fennica vol. 13 no. 4 article id 5051. https://doi.org/10.14214/sf.a14908
English title: Changes in timber assortments and loss in stumpage prices caused by decay in growing Norway spruce timber.

Material for this study was collected from 26 stands marked for clear cutting in Southern Finland. The volume of decayed Norway spruce (Picea abies (L.) H. Karst.) timber and pulpwood was determined by deducting the volumes of these assortments (as recorded on the measurement certificate) from the volume of the standing trees. To obtain the economic loss, the volume of decayed wood was multiplied by the difference in stumpage prices between spruce timber of pulpwood and pine pulpwood. In the 17 stands of Buyer A the loss in timber volume caused by decay was 5.84% and the loss in stumpage price 2.84 Fmk/m3 (means weighted by volume). The corresponding figures in the 9 stands of Buyer B were 10.87% and 5.50 Fmk/m3, respectively.

At the mean stumpage price level for the felling season 1977-78 the losses in the stands m.f.c. mentioned above were 2.87% per unit price in the stands of Buyer A and 5.75% in the stands of Buyer B.

The PDF includes a summary in English.

  • Tuimala, ORCID ID:E-mail:
article id 5008, category Article
Jyrki Raulo, Gustaf Sirén. (1978). Neljän visakoivikon päätehakkuun tuotos ja tuotto. Silva Fennica vol. 12 no. 4 article id 5008. https://doi.org/10.14214/sf.a14862
English title: Yield in volume and money of final cutting in four curly birch stands.
Original keywords: visakoivu; tuotos; laatu

Curly birch (Betula pendula f. carelica Sok.) is characterized by large variations in stem form and the internal structure of the wood, and is generally divided in to four types on the basis of visible external stem characteristics. First plantation experiments in Finland in the 1920’s in experimental areas of the Finnish Forest Institute, had become ripe for cutting and were felled. The study material of this study consists of one 52-year old and three 42–43 -year old stands of curly birch.

The yield suitable for plywood manufacture from the oldest stand was 34,777 kg/ha and that of curly grained branch wood 39,452 kg/ha. The corresponding figures of the other stands were, on average 24,219 and 57,271 kg/ha. The yield from the stands were sold at the present-day price. The result was economically better than from any other forest tree species grown in Finland. The younger stands were obviously cut too early. It was concluded that the genetic quality of the seedlings used in the plantations in the 1920’s and 1930’s was not very high.

The PDF includes a summary in English.

  • Raulo, ORCID ID:E-mail:
  • Sirén, ORCID ID:E-mail:
article id 4986, category Article
John E. Høsteland. (1978). Raakapuun hintasopimukset Norjassa. Silva Fennica vol. 12 no. 1 article id 4986. https://doi.org/10.14214/sf.a14840
English title: Collective timber price agreements in Norway.

In this paper the system of collective timber price agreement in Norway is described. The history of »collective behaviour» in the roundwood market can be tracked far back in history, with different degrees of importance, and it has totally dominated the price-formation of roundwood from the 1950’s until the present. In trying to answer the question »What has been the effect of the collective price agreements» a few theoretical market models are used and the empirical data are also employed. Both the theoretical discussion and the empirical data seem to indicate that the forest owners are better off with collective price agreements than with a situation where there are no organized price-negotiations.

The PDF includes a summary in English.

  • Høsteland, ORCID ID:E-mail:
article id 4986, category Article
John E. Høsteland. (1978). Raakapuun hintasopimukset Norjassa. Silva Fennica vol. 12 no. 1 article id 4986. https://doi.org/10.14214/sf.a14840
English title: Collective timber price agreements in Norway.

In this paper the system of collective timber price agreement in Norway is described. The history of »collective behaviour» in the roundwood market can be tracked far back in history, with different degrees of importance, and it has totally dominated the price-formation of roundwood from the 1950’s until the present. In trying to answer the question »What has been the effect of the collective price agreements» a few theoretical market models are used and the empirical data are also employed. Both the theoretical discussion and the empirical data seem to indicate that the forest owners are better off with collective price agreements than with a situation where there are no organized price-negotiations.

The PDF includes a summary in English.

  • Høsteland, ORCID ID:E-mail:
article id 4986, category Article
John E. Høsteland. (1978). Raakapuun hintasopimukset Norjassa. Silva Fennica vol. 12 no. 1 article id 4986. https://doi.org/10.14214/sf.a14840
English title: Collective timber price agreements in Norway.

In this paper the system of collective timber price agreement in Norway is described. The history of »collective behaviour» in the roundwood market can be tracked far back in history, with different degrees of importance, and it has totally dominated the price-formation of roundwood from the 1950’s until the present. In trying to answer the question »What has been the effect of the collective price agreements» a few theoretical market models are used and the empirical data are also employed. Both the theoretical discussion and the empirical data seem to indicate that the forest owners are better off with collective price agreements than with a situation where there are no organized price-negotiations.

The PDF includes a summary in English.

  • Høsteland, ORCID ID:E-mail:
article id 7027, category Article
Olli Heikinheimo, August Renvall. (1921). Über die Schutzwaldfrage. Acta Forestalia Fennica vol. 11 no. suppl. article id 7027. https://doi.org/10.14214/aff.7027
English title: About the protection forests.

The article is based on observations made during a decade in the parishes of Utsjoki and northern, middle and eastern parts of Inari in Finnish Lapland. At the timber line the pine regenerates very slowly. The amount and quality of pine forests on their timber line has been diminishing because of forestry, expansion of settlements and reindeer pasturing.  

Assigning the pine forests on the timber line as protection forests would serve the nature protection purposes as well as the wellbeing of the inhabitants and the state. Protection of areas where the regeneration is weak as well as the birch forests that serve as source of firewood for local people is of particular important. Measures against forest fires need to be taken. Extensive use of forests for reindeer pastures have caused a threat to existence of those forests.

When it comes to forest management, securing the seed yield and the survival of the seedlings need to be taken care. The productivity of the forests must be increased. For growing amount of people living in the area, the need for firewood and timber for other purposes must be fulfilled without increasing pressure to nearby forests.    

  • Heikinheimo, ORCID ID:E-mail:
  • Renvall, ORCID ID:E-mail:
article id 7026, category Article
August Renvall. (1919). Suojametsäkysymyksestä VI. Asutusolojen järjestely mäntymetsärajaseuduilla. Acta Forestalia Fennica vol. 11 no. 6 article id 7026. https://doi.org/10.14214/aff.7026
English title: Protection forests VI.

The sixth part of the six-article series about protection forest in the Northern Finland is a review of the population and villages situated in the Scots pine (Pinus sylvestris L.) timber line area, and how private use of wood can be coordinated with the protection of pine timber line. Both the preservation of forests and the use of the forest as the source of timber and fuel wood in the timber line area are essential for the local communities, especially because in the area there is are few livelihoods. The article includes a proposal for a decree for new settlements in the northern protection forest area.

The article is divided in six parts. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 7026, category Article
August Renvall. (1919). Suojametsäkysymyksestä VI. Asutusolojen järjestely mäntymetsärajaseuduilla. Acta Forestalia Fennica vol. 11 no. 6 article id 7026. https://doi.org/10.14214/aff.7026
English title: Protection forests VI.

The sixth part of the six-article series about protection forest in the Northern Finland is a review of the population and villages situated in the Scots pine (Pinus sylvestris L.) timber line area, and how private use of wood can be coordinated with the protection of pine timber line. Both the preservation of forests and the use of the forest as the source of timber and fuel wood in the timber line area are essential for the local communities, especially because in the area there is are few livelihoods. The article includes a proposal for a decree for new settlements in the northern protection forest area.

The article is divided in six parts. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 7025, category Article
August Renvall. (1919). Suojametsäkysymyksestä V. Metsänhoidon perusteet varsinaisella mäntymetsärajavyöhykkeellä. Acta Forestalia Fennica vol. 11 no. 5 article id 7025. https://doi.org/10.14214/aff.7025
English title: Protection forests V.

The fifth part of the six-article series about protection forest in Northern Finland outlines sustainable forest management practices for the Scots pine (Pinus sylvestris L.) forests in the pine timber line area. The author stresses the need to secure the seed production and regeneration capacity of the forests, and the growth and protection of seedlings. At the same time, the local communities’ need for timber has to be taken into account when considering the means to protect the pine forests. The main principle is not to cut more trees than has been regenerated during the time period between good seed years. The article outlines good forest management practices for the timber line area.

The article is divided in six parts. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 7025, category Article
August Renvall. (1919). Suojametsäkysymyksestä V. Metsänhoidon perusteet varsinaisella mäntymetsärajavyöhykkeellä. Acta Forestalia Fennica vol. 11 no. 5 article id 7025. https://doi.org/10.14214/aff.7025
English title: Protection forests V.

The fifth part of the six-article series about protection forest in Northern Finland outlines sustainable forest management practices for the Scots pine (Pinus sylvestris L.) forests in the pine timber line area. The author stresses the need to secure the seed production and regeneration capacity of the forests, and the growth and protection of seedlings. At the same time, the local communities’ need for timber has to be taken into account when considering the means to protect the pine forests. The main principle is not to cut more trees than has been regenerated during the time period between good seed years. The article outlines good forest management practices for the timber line area.

The article is divided in six parts. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 7024, category Article
August Renvall. (1919). Suojametsäkysymyksestä IV. Poronlaidunnan järjestely suojametsäalueella. Acta Forestalia Fennica vol. 11 no. 4 article id 7024. https://doi.org/10.14214/aff.7024
English title: Protection forests IV.

This fourth part of the six-article series about protection forest in the Northern Finland is a proposal for organizing reindeer grazing to enable scots pine (Pinus sylvestris L.) regeneration near the timber line. Protection forests in the Northern Finland cover third of the natural pastures of reindeer in the area. In these areas reindeer grazing can harm the young pine seedlings. The proposal suggests temporary restrictions in grazing in the coniferous forests. Also, in the northernmost parts of Lapland the pine timberline area would be used only as winter pastures. Regional limits should be set for the number of reindeer. Also the ownership of reindeer herds and herding coopearatives included problematic issues that should be solved.

The article is divided in six parts. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 4974, category Article
Markku Mäkelä. (1977). Teknisesti korjattavissa oleva hakkuutähde sekä kanto- ja juuripuu Kaakkois-Suomessa. Silva Fennica vol. 11 no. 3 article id 4974. https://doi.org/10.14214/sf.a14825
English title: The amounts of logging residues and stump and root wood technically harvestable in southeast Finland.

The amounts of harvestable logging residues and stump and root wood were examined in the area where 100,000 solid m3 of stemwood was cut in 1975. The cutting amounts of stemwood from work sites suitable for harvesting of logging residues was 35,000 m3, and suitable for harvesting of stump and root wood 38,000 m3. The increase in the yield of wood (without bark) from logging residues compared with the unbarked stemwood was 2.4%. The same percentage of wood from stump and root wood was 5.0–5.8% depending on the harvesting loss.

The PDF includes a summary in Finnish.

  • Mäkelä, ORCID ID:E-mail:
article id 4973, category Article
Olli Saastamoinen. (1977). Economics of forest uses in Finnish Lapland. Silva Fennica vol. 11 no. 3 article id 4973. https://doi.org/10.14214/sf.a14824

The object of the study was to give a tentative indication of the realized economic significance of the principal forest (forestry land) uses in Finnish Lapland. Data concerns the years of the 1970s. Nowadays timber harvesting generates a major part of the total value of production. Recreation (tourism) is in second place. Reindeer husbandry, collection of berries and mushrooms and hunting together produce, in the best years, an output value which is about one fifth of that of timber harvesting. Non-timber uses together produce a rather significant portion on the total value of the integrated forestry output.

The PDF includes a summary in Finnish.

  • Saastamoinen, ORCID ID:E-mail:
article id 7023, category Article
August Renvall. (1919). Suojametsäkysymyksestä III. Metsän suojeleminen kuloilta. Acta Forestalia Fennica vol. 11 no. 2-3 article id 7023. https://doi.org/10.14214/aff.7023
English title: Protection forests III.

The third part of the six-article series about protection forest in Northern Finland describes prevention of forest fires in the pine timber line area. The article gives a proposal for a forest fire decree. According to the proposal, lighting a campfire should be prohibited in dry and windy times. Vegetation should be cleared around a campfire in the summertime. The local people should be obliged to help to extinguish any forest fire, and given compensation for the work. The compensation would be claimed from the person who lit the fire, if that is known. A fine is collected if forest fire breaks out by negligence. 

The article is divided in six parts. The parts II and III of the article series are included in the same PDF. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 7022, category Article
August Renvall. (1919). Suojametsäkysymyksestä II. Suojametsäjärjestelmän tarkoitusperät ja edellytykset. Acta Forestalia Fennica vol. 11 no. 2-3 article id 7022. https://doi.org/10.14214/aff.7022
English title: Protection forests II.

The second part of the six-article series about protection forest in Northern Finland outlines the principles of protecting Scots pine (Pinus sylvestris L.) timber line. The protected areas should include at least all of the viable pine stands and those birch (Betula sp.) lands that are necessary to safeguard fuel wood supply in the pine forest zone. Outside the actual pine forest zone also those birch stands that are near populated regions should be protected to secure sustainable fuel wood supply. Third, south and down of the pine forest zone should be protected pine forest stands and adjacent open fell areas where forests are especially vulnerable. A new protection forest commission should be established to execute the protection forest legislation.

The article is divided in six parts. The parts II and III of the article series are included in the same PDF. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 7021, category Article
August Renvall. (1919). Suojametsäkysymyksestä I. Mäntymetsän elinehdot sen pohjoisrajalla sekä tämän rajan alenemisen syyt. Acta Forestalia Fennica vol. 11 no. 1 article id 7021. https://doi.org/10.14214/aff.7021
English title: Protection forests I.

The article aims to give a proposal on how to organize a protection forest system to protect the pine timber line in the northernmost Finland. In this first part of the six-article series is described the range and biology of Scots pine (Pinus sylvestris L.) in the timber line area, and human actions influencing the species in the area. The southward shift of Scots pine timber line cannot be explained by change of climate. The main factors are too intensive fellings, reindeer husbandry and forest fires. The poor reproduction of pine in Lapland makes it vulnerable to disturbances. The trees produce viable seeds in average only every 100 years. Thus, effective measures are needed to protect the existing pine forests in the area.

The article is divided in six parts. A German summary is in a separate PDF.

  • Renvall, ORCID ID:E-mail:
article id 4955, category Article
Suomen Metsäteollisuuden Keskusliitto. (1976). Puutavaraselvitys 1976. Silva Fennica vol. 10 no. 4 article id 4955. https://doi.org/10.14214/sf.a14801
English title: Timber report 1976. – Finland’s roundwood, industrial residue and forest residue balances by 1980 as well as the wood raw material situation of Finnish forest industries by the year 2000.

This study was carried out on behalf of the Central Association of Finnish Forest Industries (now Finnish Forest Industries Federation) in order to obtain information about the wood raw material situation, to serve, in turn, as a basis for the forest industries’ long-term planning. The study deals with the potential supply of roundwood, industrial residue and forest residue by the year 200 by five wood-supply areas. Examination of the situation during the period of 1972–80 is based on available balances and that concerning the period 1985–2000 in the estimated quantities available for industrial use.

The PDF includes a summary in English.

  • Suomen Metsäteollisuuden Keskusliitto, ORCID ID:E-mail:
article id 4950, category Article
Matti Kärkkäinen. (1976). Lisähavaintoja haapatukkien poikkipinta-alan mittaamisesta. Silva Fennica vol. 10 no. 4 article id 4950. https://doi.org/10.14214/sf.a14796
English title: Auxiliary observations on the measurement of the cross-sectional area of aspen logs.

In this study the area, 8 diameters, and 16 radii were measured of 174 discs representing aspen logs in a mill. The average difference between the largest and smallest diameter was 18 mm, or 7% of the longest diameter. The difference between the largest and smallest radius was 29 mm, or 22% of the longest radius. The diameter was on the average 2.4 mm longer than the two corresponding radii.

The exact area of each disc was measured using a planimeter. In comparison, the area based on the circle formula the diameter being the arithmetic mean of largest and smallest diameters overestimated the area by 1.7%. The results also indicated that the use of random direction in the measurement of diameter overestimated the cross-sectional area on the average by 1.8%.

The study is continuation of the earlier study where the bibliography is presented. As far as the results are comparable, they support each other.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4928, category Article
Pentti Hakkila. (1975). Metsätyötieteen asema ja tulevaisuuden näkymät metsäntutkimuslaitoksessa. Silva Fennica vol. 9 no. 4 article id 4928. https://doi.org/10.14214/sf.a14770
English title: The status and future prospects of forest work science at the Finnish Forest Research Institute.

The article reviews the position of the Department of Forest Technology in Finnish Forest Research Institute, among Finnish establishments in research on forest work. In addition, it describes the current research programmes of the departments both in wood harvesting studies and studies on silvicultural work. The equitable aims of the former are to increase productivity, lower the cost level, ease the work and improve job satisfaction, as well as to improve the utilization of wood raw material. The latter aims at e.g. improvement of the biological results.

Future prospects are surveyed from the point of view of the goals imposed by the State on the research and, on other hand, the appropriations earmarked for forest work science. A regrettable conflict has arisen between them.

The PDF includes a summary in English.

  • Hakkila, ORCID ID:E-mail:
article id 4925, category Article
Matti Kärkkäinen. (1975). Pohjoissuomalaisten mäntytukkien soikeus. Silva Fennica vol. 9 no. 4 article id 4925. https://doi.org/10.14214/sf.a14767
English title: Ovalness of Scots pine logs in Northern Finland.

The material of this study consists of 1,080 Scots pine (Pinus sylvestris L.) saw logs measures in two saw mills in Northern Finland. The largest and the smallest top-diameter of each log was measured under bark. According to the results, the ovalness was rather small, 1 mm or 4.9% on average. On the other hand, only 14.3% of all logs showed a diameter difference smaller than 2%. The ovalness was larger than 10% in 5.8% of all logs.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4922, category Article
Matti Kärkkäinen. (1975). Koivu- ja haapatukkien poikkipinta-alan mittaaminen. Silva Fennica vol. 9 no. 3 article id 4922. https://doi.org/10.14214/sf.a14764
English title: Measurement of the cross-sectional area of birch and aspen logs.

The aim of the study was to determine the extent to which the cross section of birch (Betula sp.) and aspen (Populus tremula L.) logs differ from a circle and to test some simple methods for measuring the cross-sectional area which can be used, for instance, for determining the volume of the logs. The material consisted of 420 debarked birch disks and 240 aspen disks which were representative of the logs arriving at two factories.

The convex deficit values for the material were very small, the cross-sectional area error being in general less than 1%. On the other hand, the other parameters deviated from the circular form to quite a large degree. It was also evident that the radii measured from the piths to the surface of the wood varied considerably more in the same disk, as regards length, than the diameters measured in different directions.

It was evident that the shape of the average cross-sectional area was not in general elliptical. It thus appears that any method for measuring the cross-sectional area which is based on elliptical formula is not suitable. The method which gave the best result was that in which the cross-sectional area was taken as the average of the area of the circle calculated from the smallest diameter and that calculated from the diameter passing at right angles to it. This method also appeared to be the best for disks which deviated to quite a large degree from the circular form. The suitability of this method is increased by the fact that the relative error is only slightly dependent on the size of the disk.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4921, category Article
Simo Hannelius. (1975). Ojitusalueiden kulkukelpoisuudesta puunkorjuussa. Silva Fennica vol. 9 no. 3 article id 4921. https://doi.org/10.14214/sf.a14763
English title: On the trafficability of drained peatlands in harvesting.

During the next decade there will be a marked increase in the allowable cut in drained peatlands. At the same time, the mechanization in logging proceeds, and in short-distance haulage the use of forwarders will increase. This study, based on literature and some observations, deals with logging conditions in drained peatlands with special reference to the suitability of heavy logging machines for use in such terrain. In addition, soil frost and the bearing capacity of the frozen peat soil were studied.

Freezing of the soil in a drained peatland area depends prevailingly on the weather conditions during early winter. The factors influencing soil freezing of a drained peatland are completely different from those regulating the freezing of natural peat soils. The frost penetrates in general deeper in the drained than virgin peatland. The topmost peat layer does not, however, freeze uniformly. Generally speaking, the bearing capacity of a drained peat soil is lower than that of undrained peat due to lower water content.

It is concluded that heavy logging machines are probably not fitted for use in drained areas on peatland even if the average soil frost values recorded would suggest it. Moreover, because of their extremely superficial root systems, peatland forests are exposed to damages by heavy machines in thinning operations.

The PDF includes a summary in English.

  • Hannelius, ORCID ID:E-mail:
article id 4918, category Article
Pekka Kilkki, Raimo Pökälä, Markku Siitonen. (1975). Metsätalousyksikön puuntuotannon suunnittelu lineaarista ohjelmointia käyttäen. Silva Fennica vol. 9 no. 2 article id 4918. https://doi.org/10.14214/sf.a14762
English title: Linear programming in the planning of timber production in a forestry unit.

The planning of timber production in a forestry unit is divisible into two phases. In the first phase, planning provides the decision-maker with a number of possible timber production policies; these policies define the production possibility boundary. After the decision-maker has chosen one of these policies, planning moves to the second phase, in which a detailed programme is prepared with a view to meeting the requirements of the timber production policy accepted. The paper indicates one possibility of solving these two tasks simultaneously. In the first phase, the solution of the primal linear programming problem is employed and in the second phase the respective dual or shadow price solution.

The PDF includes a summary in English.

  • Kilkki, ORCID ID:E-mail:
  • Pökälä, ORCID ID:E-mail:
  • Siitonen, ORCID ID:E-mail:
article id 4915, category Article
Yrjö Roitto. (1975). Raakapuukuljetusten optimointi. Silva Fennica vol. 9 no. 1 article id 4915. https://doi.org/10.14214/sf.a14759
English title: Optimization of roundwood transport.

The paper deals with the optimization of roundwood transport in cases where many destinations for it exist and where several means of transport are available. It is also understood that the capacities of the factories to which wood is transported can be used at varying degree. A model was developed for a case such as Finland which sells most of its products abroad.

In the above case, the optimization of roundwood transport does not necessarily mean minimization of transport costs. What is aimed at is to obtain, by using different combinations (mill destinations and the media of transport) the maximum difference between the allowable cut (calculated) and real (actual) transport costs.

The PDF includes a summary in English.

  • Roitto, ORCID ID:E-mail:
article id 4906, category Article
Lasse Lovén. (1974). Maisemanhoitomallien käyttö metsätalouden maan aluevaraussuunnittelussa. Silva Fennica vol. 8 no. 3 article id 4906. https://doi.org/10.14214/sf.a14750
English title: Regional landscape planning of forest areas.

The study deals with economic significance of forest landscape planning models used in regional planning in Finland. The »judge»-method is used among professional foresters working on private forestry boards in Southern Finland to define their view of what would be moderate level of costs of landscape management for private forest owners. A sample of 154 forest professionals working in district forestry boards in Southern Finland was sent a sociological questionnaire.

It was possible to form three hierarchical moderation classes by statistical grouping of judgement distributions. Prolongations in rotation ages and restrictions concerning ditching of forested bogs, forest read building and clear-cutting were considered the most immoderate models. Rather or wholly insignificant were evaluated such management models, which mean restrictions in »old fashioned» methods or which are already used in practice.

The PDF includes a summary in English.

  • Lovén, ORCID ID:E-mail:
article id 4900, category Article
Pertti Harstela. (1974). Eräiden koneellistamisennusteiden herkkyydestä kustannustason muutoksiin. Silva Fennica vol. 8 no. 2 article id 4900. https://doi.org/10.14214/sf.a14744
English title: The influence of the change of cost level on some mechanization prognosis.

In this study a formula has been developed to describe the influence of the change of cost level on such a mechanization prognosis, where is assumed that wages and machine costs bear compound interest. In the study there are some numerical examples.

In the formula p1 = annual per cent increase of wages, p3 = annual per cent increase of machine costs, p2 = sudden and incident per cent increase of machine costs, and tv = delay in the profitability of mechanization.

The PDF includes a summary in English.

  • Harstela, ORCID ID:E-mail:
article id 4899, category Article
Matti Kärkkäinen. (1974). Näkökohta tyvi- ja latvaläpimitan keskiarvoon perustuvasta mäntypölkkyjen kuutioinnista. Silva Fennica vol. 8 no. 2 article id 4899. https://doi.org/10.14214/sf.a14743
English title: Note on the volume based on the mean of butt and top diameters of Scots pine bolts.

In this paper the use of butt and top diameters of pulpwood bolts for volume determination is analysed. The study is based on the taper data of Scots pine (Pinus sylvestris L.) stems. According to the results, the use of the mean of butt and top diameters in the volume determination under Finnish condition causes a positive error in small stems. If the stems are so big that the butt portions of the stems can be used as saw logs, the remaining top bolts, used as pulpwood, are estimated to be smaller than they are in reality. Accordingly, there is a negative error.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4896, category Article
Matti Kärkkäinen. (1974). Keskusmuotoluvun perusteita tukkien ja kuitupuun mittauksessa. Silva Fennica vol. 8 no. 1 article id 4896. https://doi.org/10.14214/sf.a14740
English title: Foundations of middle form factor in the measurement of logs and pulpwood.

In this literature review some error possibilities in the measurement of solid volume of logs and pulpwood are discussed. Although both underestimation and overestimation can occur for various reasons it seems likely that in the stereometric measurement method the real volume is underestimated, at least when Huber’s formula is applied, and the respective middle form factors are too low. Numerous results of empirical investigations are presented in the paper, too.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4884, category Article
Kauko Hahtola, Veli-Pekka Järveläinen, Aarne Reunala. (1973). Metsänomistajien puunmyyntikäyttäytyminen. Silva Fennica vol. 7 no. 3 article id 4884. https://doi.org/10.14214/sf.a14721
English title: The timber-sales behaviour of private forest owners.

The task of this study was to gather all available information concerning timber-sales behaviour of private forest owners and to try to find the probable trends in this behaviour. The initiative for the study came from the Central Association of Finnish Forest Industries.

In Finland there are areas of timber savings and those of overcutting. These are mainly explained by regional variation in prosperity of forest owners. There are also several individual factors affecting timber sales behaviour. Without major changes in forest policy the annual variation in quantity cut in Finland is increasing and the degree of cutting seem to remain below the allowable cut.

The PDF includes a summary in English.

  • Hahtola, ORCID ID:E-mail:
  • Järveläinen, ORCID ID:E-mail:
  • Reunala, ORCID ID:E-mail:
article id 4883, category Article
Matti Kärkkäinen. (1973). Näkökohta kuitupuupölkkyjen siirtelymatkasta. Silva Fennica vol. 7 no. 3 article id 4883. https://doi.org/10.14214/sf.a14720
English title: A note on the moving distance of pulpwood bolts.

The aim of the paper was to analyse, using a computer simulation technique, the moving distance of pulpwood bolts when direct felling of trees is used and the bolts are gathered alongside the strip road. According to the results, the average moving distance of bolts depends in a complicated way on the usable part of the stem and the spacing of strip road. As a rule, the differences between moving distances of two-meter bolts weighted and unweighted by bolt volume of various trees is 0–16% when the strip road spacing is 30 m the reason being the fact that the heaviest butt bolts are often more far away from the strip road than the top bolts.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4857, category Article
Antti Lappalainen. (1971). Metsät ja verot. Silva Fennica vol. 5 no. 4 article id 4857. https://doi.org/10.14214/sf.a14659
English title: Forests and taxation in Finland.

There is no clear picture in Finland of how big the revenues are that the State and the local authorities receive from taxation for the part of primary forestry. Conception of taxation varies from 100% to 50%. The paper presents a comparison between the gross income from timber sales as determined according to the method used at the Central Statistics Bureau and the net revenues as calculated on the basis of forest fee.

At 1920s area taxation was introduced in forest taxation. The system is based on forest types and their timber production capacity. According to the principles of area taxation, no tax is paid for overcuts, whereas timber capital savings should be paid for.

According to the calculations of this study, in 1958–62 the gross income from timber sales was about 506 million Fmk annually in Southern Finland, the costs involved in timber production about 437 million Fmk, and the annual taxable income 231 million Fmk. In the period more valuable timber assortments were harvested than those for which taxes were paid according to the old regulations.

Half a century ago, area taxation was a system suited to its purpose. Now, however, forestry is in the hands of another generation, and accounting has been introduced in practical agriculture and forestry. Therefore, a taxation system based on the real income from timber growing should be introduced. The transition period could even be relatively short. It seems probable that a forest owner does not sell timber at a time when this would be required by silvicultural aspects in order to avoid income taxation, he should have to be present an acceptable working plan.

The PDF includes a summary in English.

  • Lappalainen, ORCID ID:E-mail:
article id 4855, category Article
Peitsa Mikola. (1971). Puuntuotannon ja metsien virkistyskäytön koordinointi Saksan liittotasavallassa. Silva Fennica vol. 5 no. 4 article id 4855. https://doi.org/10.14214/sf.a14657
English title: Integration on timber production and forest recreation in the German Federal Republic.

The article is a report of a study tour of five Finnish foresters in Germany on September 27 – October 2. 1971. As in most industrial countries, the recreation use of forests is rapidly expanding and, therefore, its needs are considered in the management of forests. Two examples of intensively used recreation forests are described, Schönbuch near Stuttgart and the Bavarian Forest National Park at the Czechoslovakian border. These forests are effectively used for both timber production and recreation at the same time. Some other effects of urbanization on forests also are discussed in the article.

The PDF includes a summary in English.

  • Mikola, ORCID ID:E-mail:
article id 4848, category Article
Matti Kärkkäinen. (1971). Lahon leviäminen puunkorjuun aiheuttamista kuusen runko- ja juurivaurioista. Silva Fennica vol. 5 no. 3 article id 4848. https://doi.org/10.14214/sf.a14650
English title: Decay following logging injury in stems and roots of Norway spruce.

The material of 78 damaged Norway spruce (Picea abies (L.) H. Karst.) trees was gathered in Southern Finland in order to clarify the advance of decay. The harvesting which had caused the scars had been carried out 12 years earlier and at the moment of the investigation the growing stand was 110 years old. It was noticed that the variables used could explain only a few per cent of the variation of the advance of decay. It was concluded that the only important thing in practice is whether the injuries are in roots or in stems.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4846, category Article
Olavi Linnamies. (1971). Metsäteollisuutemme laajennukset ja puuraaka-aineen riittävyys. Silva Fennica vol. 5 no. 3 article id 4846. https://doi.org/10.14214/sf.a14648
English title: Expansion capacity of Finnish forest industries and the sufficiency of wood raw material.

The Finnish forest industries have doubled their use of wood raw material during the past two decades. The average annual overcut of 4.0 million m3 in 1960–64 has been turned into an average annual surplus of 2.7 million m3 in 1965–69. By 1974 industry’s requirements for domestic roundwood would increase by about 6.3 million m3, if all new capacity can be taken into full production. The MERA allowable cut, if realized, would leave a 1.5 million m3 annual surplus in the forest balance in 1974. Less intensive forestry programs would mean a 1.5 to 4.4 million m3 overcut in 1974.

The PDF includes a summary in English.

  • Linnamies, ORCID ID:E-mail:
article id 4843, category Article
Unto Silvennoinen, Rihko Haarlaa. (1971). Metsätraktoreiden liikkuvuus lumessa. Silva Fennica vol. 5 no. 2 article id 4843. https://doi.org/10.14214/sf.a14645
English title: The mobility of logging tractors on snow.

The mobility of logging tractors was tested in the winter 1969 on difficult snow conditions to gather information for planning of logging operations and for logging machinery design. The tractors tested were Clark Ranger 666, Timberjack C, Valmet Terra, Ford Brunett 5000, Fiskars 510, BM-Volvo SM 660, BM Volvo SM 661, Ford Country 6, MF-Robur I and BM-Boxer T-350.

According to the results, there is a preference of tracked vehicles in difficult snow conditions compared to wheeled tractors. Ford Country with long and bearing full-tracks proved to have the best mobility. On downhill grades it was found significant differences between three-quarter-track-tractors and skidders, although the performance on level ground and uphill grades was relatively similar. The tracked vehicles can easier move on the packed snow layer and reach a higher speed.

The driving speed does not increase significantly until the density of snow has entirely changed through getting wet. Wet top layer of snow affects positively on driving, because it increases packing of the snow. Increasing density of the snow improves especially the mobility of broad-tired wheeled tractors. To be able to predict the driving speed of a tractor in winter working conditions one must know the depth of the snow layer and the density of the snow and the grade of the slope. In addition, the passages on the same route and the packing of the snow must be regarded.

The PDF includes a summary in English.

  • Silvennoinen, ORCID ID:E-mail:
  • Haarlaa, ORCID ID:E-mail:
article id 4820, category Article
Rihko Haarlaa. (1970). Ideaalinäkemys metsätyöorganisaatioiden kehittämisestä. Silva Fennica vol. 4 no. 2 article id 4820. https://doi.org/10.14214/sf.a14609
English title: The concept of ideal systems in design of forestry work organizations.

The most effective work organization will be used as a goal in minimizing of logging costs. Some type of problem approach is usually utilized. The concept of the ideal system offers a possibility to get guidance in this difficult task. The idea of an ideal system is based on the fact that an ideal system, even imagined, can be utilized for any purpose. There are checklists in handbooks to accomplish the four existing steps: define of function, design ideal, develop optimum and deliver results.

In this paper two special cases are taken up to illustrate the concept itself, and it’s use in design of forestry work organizations. There were found no such reasons which could limit or even prevent the use of this method for forest technological purposes. That is why the author believes the method to give better results than any other customary approach.

The PDF includes a summary in English.

  • Haarlaa, ORCID ID:E-mail:
article id 4819, category Article
Matti Kärkkäinen. (1970). Hakkuutähteiden merkityksestä puuston vaurioitumisen ja raiteenmuodostuksen kannalta harvennusmetsissä. Silva Fennica vol. 4 no. 2 article id 4819. https://doi.org/10.14214/sf.a14608
English title: Significance of logging waste in thinnings as to scars and tracks in the terrain.

The purpose of this study was to explain whether it is possible to affect, in practical working site conditions, by means of logging waste on the strip road, the depth of the track which is formed in terrain transportation and the injuries of the growing stand. Five 20 m long investigation areas with logging waste and five similar areas without logging waste were arranged on one strip road at Teisko logging site in Southern Finland. The logging waste layer was mainly Norway spruce and 10–15 cm thick. A KL–836 B forwarder was used. The type of soil was loam.

The logging waste affected the depth of the track only by decreasing the wear of humus layer. Even decreasing effect of logging waste on the injuries in the growing stand was minor. At Kitee working site in Eastern Finland strip roads were studied. The type of soil was thick, rather mouldered peat. The thickness of logging waste was 3–4 times greater than in Teisko, mainly spruce. A Volvo Nalle SM 460 forwarder was used. The effect of the logging waste on the depth of the tracks was clearly to be noticed. On basis of the appearance of the tracks one could assume that the difference was due to different wear of the humus, and not so much due to the quantity of logging waste that improves the carrying capacity of terrain.

In some extent logging waste was also found to affect the amount and quality of tree injuries. In practical working conditions, the importance might be small, since in the experiments an unrealistically great amount of logging waste was used.

The PDF includes a summary in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 4806, category Article
Esko Leinonen, Pentti Rikkonen. (1969). Puutavaran kuorma- ja kuormaotantamittaus. Silva Fennica vol. 3 no. 4 article id 4806. https://doi.org/10.14214/sf.a14594
English title: Load and load sampling measurement of timber.

Measurement of timber in a vehicle load or in a bundle is best performed at the mill where the measuring of large quantities can be mechanized and sampling is possible. Load measurement methods include calculation of the number of units, measurement of pile volume, weight scaling and determination of solid content in accordance with Archimedes principle by immersion in water. For some timber assortments, load measurement is sufficiently accurate and suitable unit of measure. The accuracy of load measurement can be increased or the result can be converted by sampling to a more appropriate unit of measure.

In load sampling measurement, a sample is taken from the population, and the desired more accurate measurement is made from the sample. The basic measurement for the whole population can be converted into the more accurate measuring unit by means of the ratio between it and the basic measure. Unit, pile and weight sampling can be used. The aim for pulpwood is to calculate the dry matter content without bark, which means that the amount of bark and the dry weight of wood must be determined by sampling.

The size of the sample depends on size of the population, variation of the ratio between the loads, and the accuracy required. As the quantity of wood to be measured decreases, sampling measurement will reduce the measuring costs by up to 80%. In addition, there is saving in costs by rationalization.

The PDF includes a summary in English.

  • Leinonen, ORCID ID:E-mail:
  • Rikkonen, ORCID ID:E-mail:
article id 4806, category Article
Esko Leinonen, Pentti Rikkonen. (1969). Puutavaran kuorma- ja kuormaotantamittaus. Silva Fennica vol. 3 no. 4 article id 4806. https://doi.org/10.14214/sf.a14594
English title: Load and load sampling measurement of timber.

Measurement of timber in a vehicle load or in a bundle is best performed at the mill where the measuring of large quantities can be mechanized and sampling is possible. Load measurement methods include calculation of the number of units, measurement of pile volume, weight scaling and determination of solid content in accordance with Archimedes principle by immersion in water. For some timber assortments, load measurement is sufficiently accurate and suitable unit of measure. The accuracy of load measurement can be increased or the result can be converted by sampling to a more appropriate unit of measure.

In load sampling measurement, a sample is taken from the population, and the desired more accurate measurement is made from the sample. The basic measurement for the whole population can be converted into the more accurate measuring unit by means of the ratio between it and the basic measure. Unit, pile and weight sampling can be used. The aim for pulpwood is to calculate the dry matter content without bark, which means that the amount of bark and the dry weight of wood must be determined by sampling.

The size of the sample depends on size of the population, variation of the ratio between the loads, and the accuracy required. As the quantity of wood to be measured decreases, sampling measurement will reduce the measuring costs by up to 80%. In addition, there is saving in costs by rationalization.

The PDF includes a summary in English.

  • Leinonen, ORCID ID:E-mail:
  • Rikkonen, ORCID ID:E-mail:
article id 4801, category Article
Rihko Haarlaa. (1969). Puunkorjuun suunnittelu ja metsätaloussuunnitelmat. Silva Fennica vol. 3 no. 3 article id 4801. https://doi.org/10.14214/sf.a14589
English title: The role of logging in forest management plans.

The purpose of this study was to answer questions concerning the basic information in planning of timber harvesting, how this information has to be handled, and how the planning of logging has to be combined with other forest management planning.

A deductive research method was used. By analysing a logging plan, prepared for a certain forest area, general conclusions were reached. To prepare the logging plan in connection with the forest management plan, the following information was found to be necessary: boundaries of the area, extent and ownership of the planned area, maps including information of the location of the timber and the conditions for transportation, road network and a reliable picture of the difficulty of the forest terrain.

Based on the material of the present timber harvesting methods it will be possible to predict the logging methods which will be applicable in the near future. The object to be planned has to be divided to operation areas. The amount of manpower and equipment needed can be estimated for each phase of the timber harvesting chain on the basis of the information calculated in this manner. Investments to machines and basic improvement works have to be planned before the effect of planning can be calculated in the logging costs, which are to be minimized. Due to the rapid development of the field, the handling of the material in connection with a forest management plan has to be left partly unfinished since the development of future logging methods cannot be reliably predicted.

The PDF includes a summary in English.

  • Haarlaa, ORCID ID:E-mail:
article id 4768, category Article
Veijo Heiskanen. (1968). Havaintoja eräiden vikaisuuksien vaikutuksesta mäntytukkien sahauksessa. Silva Fennica vol. 2 no. 3 article id 4768. https://doi.org/10.14214/sf.a14553
English title: Influence of some log defects in sawing of pine logs.

The present paper presents studies on the influence of some relatively common defects of Scots pine logs in Northern Finland on both the sawing yield and on the quality of the sawn goods. The study was based on test sawing of 25 logs for each of the defects (upright limb, heart shake and various kinds of wounds and scars) at Karihaara sawmill. The yield was graded into grades used for export timber according to the system of the sawmill. The proportion of the different export grades (U/S), fifths, sixths and culls) were used as characteristics together with the ratio of raw-wood consumption expressed as cu.ft/std.

Upright limbs occurring in a piece of sawn timber was shown to lower its quality to fifth grade in 43.5%, to sixth grade in 46.8% and to the category of culls in 6.5% of all cases. Only 3.2% of the cases the piece remained in U/S-grades. The size of the upright limb was the most important factor lowering the quality and affecting the ratio of raw-wood consumption.

Heart shakes are relatively common defects in pine logs deriving from over-mature trees. The quality-decreasing influence on the sawing yield depends clearly on the length of the shake in the cross-section. The same characteristics also decreases the ratio of raw-wood consumption. In addition, twisting and star shakes are considerably more harmful than straight ones. If rot occurs in connection with shakes, the places marred by the shakes are only capable of yielding sixth-grade sawn goods or culls.

Scar encountered in logs affect the sawn yield and its quality to quite a varying degree, but these defects themselves may also vary considerably both in size and quality. The length of the scar is highly significant as a quality-decreasing factor. If, in addition, rot is encountered, the defect is of a severe nature.

The PDF includes a summary in English.

  • Heiskanen, ORCID ID:E-mail:
article id 4762, category Article
Ilmo Rinkinen. (1968). Kehitysvaihtoehtoja Suomen metsätalouden organisaatioketjuissa. Silva Fennica vol. 2 no. 1 article id 4762. https://doi.org/10.14214/sf.a14546
English title: Development alternatives in the organization chains of Finnish forestry.

The aim of this paper was to shape and analyse certain alternatives in the development processes in the organization chains of Finnish forestry. The material was collected by analysing market structures and characteristics of competition with regard to raw wood and forest industry products.

The paper presents two alternative ways to rationalize the organization chains between the forest owner’s organizations and forest industry. In the price mechanism of raw wood originating from Finnish private forests there there has been increasing influence of the central organizations of the private forest owners and forest industry. In their relationship, the model of bilateral monopolistic competition can be chosen as a conceptual framework.

Under bilateral monopoly price is fixed as a result of negotiations between competitive parties, and the position and tactics within the negotiations are of great importance for the negotiating parties. Because of the competition, Finnish forest industry cannot compensate the increase in the production costs by raising independently the export prices of its products. This and the fact that the annual earnings of forest workers are fixed by law to the earnings of the workers in wood-processing industry, will cause pressure on stumpage prices.

In the paper two schemes are outlined. In the Scheme 1 a development alternative is described in which the organization chain of private forest owners is supposed to develop to the industry growing direction. In the Scheme 2 the organization chain of private forest owners is supposed to develop to the organizational orientated direction.

It is concluded that as long as the forest owners’ organizational orientated central organization is too weak to form a monopoly as counterweight to the monopsol of forest industry (except the industries of forest owners), it will consider the industry growing direction superior to the organizational orientated alternative.

The PDF includes a summary in English.

  • Rinkinen, ORCID ID:E-mail:
article id 4762, category Article
Ilmo Rinkinen. (1968). Kehitysvaihtoehtoja Suomen metsätalouden organisaatioketjuissa. Silva Fennica vol. 2 no. 1 article id 4762. https://doi.org/10.14214/sf.a14546
English title: Development alternatives in the organization chains of Finnish forestry.

The aim of this paper was to shape and analyse certain alternatives in the development processes in the organization chains of Finnish forestry. The material was collected by analysing market structures and characteristics of competition with regard to raw wood and forest industry products.

The paper presents two alternative ways to rationalize the organization chains between the forest owner’s organizations and forest industry. In the price mechanism of raw wood originating from Finnish private forests there there has been increasing influence of the central organizations of the private forest owners and forest industry. In their relationship, the model of bilateral monopolistic competition can be chosen as a conceptual framework.

Under bilateral monopoly price is fixed as a result of negotiations between competitive parties, and the position and tactics within the negotiations are of great importance for the negotiating parties. Because of the competition, Finnish forest industry cannot compensate the increase in the production costs by raising independently the export prices of its products. This and the fact that the annual earnings of forest workers are fixed by law to the earnings of the workers in wood-processing industry, will cause pressure on stumpage prices.

In the paper two schemes are outlined. In the Scheme 1 a development alternative is described in which the organization chain of private forest owners is supposed to develop to the industry growing direction. In the Scheme 2 the organization chain of private forest owners is supposed to develop to the organizational orientated direction.

It is concluded that as long as the forest owners’ organizational orientated central organization is too weak to form a monopoly as counterweight to the monopsol of forest industry (except the industries of forest owners), it will consider the industry growing direction superior to the organizational orientated alternative.

The PDF includes a summary in English.

  • Rinkinen, ORCID ID:E-mail:
article id 4761, category Article
Pentti Nisula. (1968). Ehdotus metsikön kuution ja käyttöpuuosuuden määrittämiseksi. Silva Fennica vol. 2 no. 1 article id 4761. https://doi.org/10.14214/sf.a14545
English title: A proposal for the determination of total volume and utilization per cent of standing timber .

The present study gives an account of the dependence prevailing between the actual volume of timber crops, and, on one hand, the sum of cylindrical volume of individual trees, and on the other hand, the utilization per cent. This dependence is rectlinear if the volumes in question are calculated on a running-foot basis. The cylindrical volume of individual trees was calculated on the basis of cross-section area at breast height and the height of the trees. On the basis of the results, it seems that it is possible to simplify timber measurement.

The PDF includes a summary in English.

  • Nisula, ORCID ID:E-mail:
article id 7512, category Article
Mauno Pesonen, Arto Kettunen, Petri Räsänen. (1995). Non-industrial private forest landowners’ choices of timber management strategies. Acta Forestalia Fennica no. 250 article id 7512. https://doi.org/10.14214/aff.7512

The factors affecting the non-industrial, private forest owners’ (NIPF) strategic decisions in management planning are studied. A genetic algorithm is used to induce a set of rules predicting potential cut of the forest owners’ choices of preferred timber management strategies. The rules are based on variables describing the characteristics of the landowners and their forest holdings. The predictive ability of a genetic algorithm is compared to linear regression analysis using identical data sets. The data are cross-validated seven times applying both genetic algorithm and regression analyses in order to examine the data-sensitivity and robustness of the generated models.

The optimal rule set derived from genetic algorithm analyses included the following variables: mean initial volume, forest owner’s positive price expectations for the next eight years, forest owner being classified as farmer, and preference for the recreational use of forest property. When tested with previously unseen test data, the optimal rule set resulted in a relative root mean square error of 0.40.

In the regression analyses, the optimal regression equation consisted of the following variables: mean initial volume, proportion of forestry income, intention to cut extensively in future, and positive price expectations for the next two years. The R2 of the optimal regression equation was 0.3 and the relative root mean square error from the test data 0.38.

In both models, mean initial volume and positive stumpage price expectations were entered as significant predictors of potential cut of preferred timber management strategy. When tested with complete data set of 201 observations, both the optimal rule set and the optimal regression model achieved the same level of accuracy.

  • Pesonen, ORCID ID:E-mail:
  • Kettunen, ORCID ID:E-mail:
  • Räsänen, ORCID ID:E-mail:
article id 7510, category Article
Arto Rummukainen, Heikki Alanne, Esko Mikkonen. (1995). Wood procurement in the pressure of change. Acta Forestalia Fennica no. 248 article id 7510. https://doi.org/10.14214/aff.7510

Linear optimization model was used to calculate seven wood procurement scenarios for years 1990, 2000 and 2010. Productivity and cost functions for seven cutting, five terrain transport, three long distance transport and various work supervision and scaling methods were calculated from available work study reports. All methods are based on Nordic cut to length conditions. Finland was divided in three parts for description on harvesting conditions. Twenty imaginary wood processing points and their wood procurement areas were created for these areas. The procurement systems, which consists of the harvesting conditions and work productivity function, were described as a simulation model. In the LP-model the wood procurement system has to fulfil the volume and wood assortment requirements of processing points by minimizing the procurement cost. The model consists of 862 variables and 560 restrictions.

Results show that it is economical to increase the mechanical work in harvesting. Cost increment alternatives effect only little on profitability of manual work. The areas of later thinnings and seed tree- and shelterwood cuttings increase on cost of first thinnings. In mechanized work one method, 10-tonne one grip harvester and forwarder, is gaining advantage among other methods. Working hours of forwarder are decreasing opposite to the harverster. There is only little need to increase the number of harvesters and trucks or their drivers from today’s level. Quite large fluctuations in level of procurement and cost can be handled by constant number of machines, by alternating the number of season workers and by driving machines in two shifts. It is possible, if some environmental problems of large-scale summer time harvesting can be solved.

  • Rummukainen, ORCID ID:E-mail:
  • Alanne, ORCID ID:E-mail:
  • Mikkonen, ORCID ID:E-mail:
article id 7509, category Article
Mauno Pesonen. (1995). Non-industrial private forest landowners’ choices of timber management strategies and potential allowable cut. Acta Forestalia Fennica no. 247 article id 7509. https://doi.org/10.14214/aff.7509

In the study, the potential allowable cut in the district of North-Savo, Eastern Finland was clarified  based on the non-industrial private forest landowners’ (NIPF) choices of timber management strategies. Alternative timber management strategies were generated, and the choices and factors affecting the choices of timber management strategies by NIPF landowners were studied. The choices of timber management strategies were solved by maximizing the utility functions of the NIPF landowners. The parameters of the utility functions were estimated using the Analytic Hierarchy Process (AHP).

The level of the potential allowable cut was compared to the cutting budgets based on the 7th and 8th National Forest Inventories (NFI7, NFI8) in Finland, to the combining of private forestry plans, and to the realized drain from non-industrial private forests. The potential allowable cut was calculated using the MELA system that has been used in calculating the national cutting budget.

The data consisted of the NIPF holdings that had been inventoried compartmentwise and had forestry plans made in 1984–92. The NIPF landowners’ choices of timber management strategies were clarified by a mail inquiry.

The most preferred strategy obtained was ”sustainability” (chosen by 62% of landowners). The second was ”finance” (17%) and the third ”savings” (11%). ”No cuttings”, and ”maximum cuttings” were the least preferred (9% and 1%, resp.). The factors promoting the choices of strategies with intensive cuttings were: a) ”farmer as forest owner” and ”owing fields”, b) ”increase in the size of the forest holding”, c) agriculture and forestry orientation in production, d) ”decreasing short-term stumpage earnings expectations”, e) ”increasing intensity of future cuttings”, and f) ”choice of forest taxation system based on site productivity”.

The potential allowable cut defined in the study was 20% higher than the average of the realized drain in 1988–93, which was at the same level as the cutting budget based on the combining of forestry plans in Eastern Finland. The potential allowable cut defined in the study was 12% lower than the NFI8-based greatest sustained allowable cut for the 1990. Using the method, timber management strategies can be clarified for private forest owners.

  • Pesonen, ORCID ID:E-mail:
article id 7684, category Article
Pekka Mäkinen. (1993). Puutavaran kuljetusyritysten menestymisen strategiat. Acta Forestalia Fennica no. 238 article id 7684. https://doi.org/10.14214/aff.7684
English title: Strategies used by timber truck companies to ensure business success.

The aim of the study was to determine how timber truck transport business succeeds in the competition within its sector, and the effect it has on profitability structure of the sector. Furthermore, strategic groups were looked at in depth, as well as the competitive strategies of the most successful companies and groups of companies. The theoretical competitive strategy was operationalized.

A total of 53 timber truck transport entrepreneurs were interviewed. The average age of the entrepreneurs was 51 years. Of the businesses, 35% were partnership companies, 6% open companies, and 59% self-employed. The business owned an average 1.5 trucks, and at the time of interviewing their average age was four years. Nearly nine out of ten entrepreneurs had no schooling for the line of business, and four out of five had no short-term training. The attitude of the timber truckers toward their activities was more like that of self-employed persons than that of entrepreneurs. A total of 61.5% of them reporter that they carried on entrepreneurship simply to assure themselves a job.

The operational profitability of the sector has been good in the years 1984 to 1990, and the business profitability fairly good. The median equity ratio in the sector has remained at about 20% and the ratio of debts to turnover about 40%. The sector has been more profitable than forest machine contracting primarily due to the barriers to entry into the sector.

Cluster analysis, using Ward’s method, was used for seeking out strategic groups. The lengths of the customer relationships proved a significant barrier to mobility. The most successful business used the competitive strategy of cost weighted focussing. This was done through optimization of the capacity utilization rate and through choice of correct customers. The strategic position for successful business was judged to be good in the future. Success in the future will require above all activeness and innovation ability.

The PDF includes a summary in English.

  • Mäkinen, ORCID ID:E-mail:
article id 7679, category Article
Ville Ovaskainen. (1992). Forest taxation, timber supply, and economic efficiency. Acta Forestalia Fennica no. 233 article id 7679. https://doi.org/10.14214/aff.7679

The effects and relative efficiency of alternative forest taxes are analysed theoretically. The Fisherian two-period model of consumption, savings and timber harvesting is extended by incorporating the management intensity decision and deriving the concept of long-run timber supply. The effects of lump-sum (site productivity), realized income (yield) and ad valorem property taxes on short-run timber supply, management intensity, and long-run timber supply are established. As the core of the study, the alternative taxes are compared in order to determine the appropriate forest tax regime in terms of production efficiency. The efficiency criterion generally requires that the excess burden of taxation at any given tax revenue should be kept to a minimum. The study distinguishes between an initially undistorted economy and an economy with pre-existing distortions due to capital income taxation (interest charge deductions). When the effects on forest management decisions of forest and capital income taxes are considered as a whole, a neutral forest taxation is no longer efficient. The non-timber benefits of a forest are incorporated to examine the robustness of the tax results with respect to the objective function. Finally, forest tax issues specific to Finland are considered, and administrational and equity aspects are discussed.

The PDF includes a summary in Finnish.

  • Ovaskainen, ORCID ID:E-mail:
article id 7635, category Article
Reino Pulkki. (1984). A spatial database - heuristic programming system for aiding decision-making in long-distance transport of wood. Acta Forestalia Fennica no. 188 article id 7635. https://doi.org/10.14214/aff.7635

The applicability of operations research, database management systems and geographic information systems for decision-making in long-distance transport of wood in the Saimaa area in Central Finland were reviewed. Due to the complexity of the transport problem a geographic information system is the most applicable. However, investment in such a system for only long-distance transport decision-making is unjustified. A spatial database – heuristic programming system was developed. It was applied to studying the competitiveness and search for possible areas for rationalization of water transport in particular and long-distance transport in general. The system proved to be a useful aid in long-distance transport research. Also, with the increased use of computers for planning at the field level, a system similar to that described could be a powerful managerial aid.

The PDF includes a summary in Finnish.

  • Pulkki, ORCID ID:E-mail:
article id 7626, category Article
Aarne Nyyssönen, Risto Ojansuu. (1982). Metsikön puutavaralajirakenteen, arvon ja arvokasvun arviointi. Acta Forestalia Fennica no. 179 article id 7626. https://doi.org/10.14214/aff.7626
English title: Assessment of timber assortments, value and value increment of stands in Finland.

The paper is the final report of a study on the estimation of value increment and inherent variables of Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) H. Karst.) stands. The main aim was to obtain improved criteria for decision-making concerning the priority of stands for regeneration.

The construction of various estimation models and their reliability are discussed in detail. The study, together with some previous papers, has resulted in a system which on the basis of a number of easily assessed stand variables gives for the stands concerned the volume of stems, percentages of timber assortments, stumpage value, volume increment and value increment.

The following examples are given with regard to the practical application of the results, in addition to the determination of the relative maturity of stands: 1) The study of various trends in stand development; the comparison between the volume and value variables. 2) The estimation of timber assortments needed for a cutting budget, trees marked for felling etc. 3) The calculation of the value of forests.

The PDF includes a summary in English.

  • Nyyssönen, ORCID ID:E-mail:
  • Ojansuu, ORCID ID:E-mail:
article id 7598, category Article
T. Eriksson, G. Nilsson, G. Skråmo. (1978). The Inter-Nordic project of terrain and machines 1972-1975. Acta Forestalia Fennica no. 164 article id 7598. https://doi.org/10.14214/aff.7598

The paper is the final report of the Inter-Nordic Terrain-machine Project (1972–1975). It deals with the requirements for a terrain classification for forestry, its factors and classes, and presents a terrain classification.

The mechanization of hauling, which took place in the field of forestry in the 1950's, added to the need for a terrain classification. Different terrain classifications based on different terrain factors have been developed in many countries. In the meeting of IUFRO Section 32 held in Montreal in 1964, it was found that a general system was needed for measuring and describing those terrain conditions having a significant influence on forest operations. The requirements for such a classification system are given in the paper. Because some of the requirements are contradictory, the classification must be a compromise. The most important factors from the forestry point of view are presented in the article.

The terrain classification presented in this report consists of two stages. The first stage is a primary terrain classification, in which terrain factors are measured or described objectively. The second is a secondary descriptive classification. Only factors essential to the activity in question are taken into account. After this, in a secondary functional stage, the requirements of the employer of the system, e.g., working method, machines etc., are also taken into account.

The PDF includes a summary in Finnish.

  • Eriksson, ORCID ID:E-mail:
  • Nilsson, ORCID ID:E-mail:
  • Skråmo, ORCID ID:E-mail:
article id 7591, category Article
Heikki Juslin. (1977). Yksityismetsänomistajien puunmyyntiasenteisiin vaikuttaminen. Acta Forestalia Fennica no. 157 article id 7591. https://doi.org/10.14214/aff.7591
English title: Influencing private forest owners’ attitudes towards timber sales.

The purpose of the study was to produce information which is needed when planning the influencing the timber sales propensity of private forest owners. The study deals with the relations between communication behaviour and cutting behaviour as well as the attitudes and norms connected with them. On the basis of the results of this study, the choice of psychodynamic model can be recommended as a main strategy of influencing the timber sales propensity of forest owners. The paper gives the information basis for the choice of channels and messages of influencing.

The PDF includes a summary in English.

  • Juslin, ORCID ID:E-mail:
article id 7587, category Article
Yrjö Roitto. (1976). The economic transport unit size in roundwood towing on Lake Iso-Saimaa [in eastern Finland]. Acta Forestalia Fennica no. 153 article id 7587. https://doi.org/10.14214/aff.7587

The transport unit in roundwood towing on Lake Iso-Saimaa in Central Finland comprises a tug and a raft of bundled wood with a towline between them. There are several factors influencing the economic size of the transport unit in roundwood towing. These are changing with the enterprises and along with general developments. In this paper these factors or factor groups are seen from the point of view of the enterprise. The main question is to determine the most economic combination of tug and raft size.

From the point of view of the towing enterprises the unit costs of transport are the most decisive factor. Both the size of the raft as well as the power of the tug influence strongly the unit costs. As a long-term goal a raft of about 35,000 m3 and a tug of 550 kW or more is considered to be advisable. The width of channels and sounds then allow a free passage for rafts being 36–40 m wide.

The PDF includes a summary in Finnish and in French.

  • Roitto, ORCID ID:E-mail:
article id 7582, category Article
Pentti Alho. (1975). Metsien tuoton alueellisista eroista Suomessa. Acta Forestalia Fennica no. 148 article id 7582. https://doi.org/10.14214/aff.7582
English title: Regional differences in forest returns within Finland.

The aim of this paper was to study the nature of the relative areal differences in the Finnish forests in respect of timber yield, intensity of exploitation and stumpage prices. The yield index is the most inconsistent and the source of the greatest regional differences. The differences arise even in Southern Finland, as the yield in the South-West is only 80 % of that obtained in Eastern Häme. The areal variations in the wastage index are of the order of only 10 % at most, and the stumpage price index is relatively constant, remaining within the 10 % limit, as far north as the southern boundary of the province of Oulu.

Indices for the forest yield and final forest returns suggest that the further one goes in Finland the greater the discrepancy between the two, as a consequence of the increase in stumpage price differences. Thus, whereas the yield per hectare in North-Eastern Finland is about 20 % of that in Eastern Häme, the stumpage price is similarly only just over 50 % of that prevailing in the latter area. This, the resulting returns per hectare are only 10 % of those obtainable in the more southerly area. When the return per hectare for the Forestry Board District of Eastern Häme is represented by the index 100, one then obtains corresponding return indices of 21.0 for the Northern Ostrobothnia and Kainuu area, 13.0 for Lapland and 10.0 for North-Eastern Finland. Thus, it may be said that roughly 10 hectares of forest land in Lapland, 5 in Northern Ostrobothnia or Kainuu, or 2 in Northern Karelia or the coastal area of southern and central Ostrobothnia would be required to produce the same returns as 1 hectare in Eastern Häme. This represents an extremely wide range of variation within the borders of one country.

This work provides a clear and sufficiently accurate impression of the order of magnitude of the areal differences in returns from the Finnish forests, and may thus serve as an adequate basis for the taking of decisions in this field.

The PDF includes a summary in English.

  • Alho, ORCID ID:E-mail:
article id 7577, category Article
Pekka Kilkki, Raimo Pökälä. (1975). A long-term timber production model and its application to a large forest area. Acta Forestalia Fennica no. 143 article id 7577. https://doi.org/10.14214/aff.7577

A long-term timber production model was developed. The model is based upon numerical simulation and it is viewed only as a means of providing the decision-maker with values of the predicting variables in his utility function. Special attention was paid to the development of automatic cutting decision rules. The model was applied to the area of 2,752,000 hectares of forest land in Central Finland. The measurement data were extracted from the Sixth National Forest Inventory, which was made in 1973. Utilities from a hypothetical utility function were attained to a number of feasible timber production policies. The Bayes and maximin criteria were employed to evaluate these policies.

The PDF includes a summary in Finnish.

  • Kilkki, ORCID ID:E-mail:
  • Pökälä, ORCID ID:E-mail:
article id 7577, category Article
Pekka Kilkki, Raimo Pökälä. (1975). A long-term timber production model and its application to a large forest area. Acta Forestalia Fennica no. 143 article id 7577. https://doi.org/10.14214/aff.7577

A long-term timber production model was developed. The model is based upon numerical simulation and it is viewed only as a means of providing the decision-maker with values of the predicting variables in his utility function. Special attention was paid to the development of automatic cutting decision rules. The model was applied to the area of 2,752,000 hectares of forest land in Central Finland. The measurement data were extracted from the Sixth National Forest Inventory, which was made in 1973. Utilities from a hypothetical utility function were attained to a number of feasible timber production policies. The Bayes and maximin criteria were employed to evaluate these policies.

The PDF includes a summary in Finnish.

  • Kilkki, ORCID ID:E-mail:
  • Pökälä, ORCID ID:E-mail:
article id 7572, category Article
Tauno Kallio, Pekka Tamminen. (1974). Decay of spruce (Picea abies (L.) Karst.) in the Åland Islands. Acta Forestalia Fennica no. 138 article id 7572. https://doi.org/10.14214/aff.7572

In 1972, all Norway spruce (Picea abies (L.) H. Karst.) trees of a minimum 7 cm diameter at breast height growing in the sample plots of the Sixth National Forest Inventory were examined on the main island of Aland, Finland. The soundness of standing trees was estimated by means of external characteristics and increment borer chips. The trees were then felled and measured. They were cut into lengths, and the type and extent of decay were studied.

30% of the trees examined was affected by butt rot, ca. 3% by wound decay. A comparison of the results with those of the Sixth National Forest Inventory justifies the estimate that in Aland 23% of spruce trees exceeding 7 cm in diameter at 1.3 m had butt rot.

The proportion of decayed trees in the cubic volume was 31%. Decayed wood material accounted for 5% of the volume including bark. Butt rot increased towards the mature stands. The reduction in the number of timber trees due to decay was 14.5%, in their volume 21.5%, and in the volume of sulphite pulpwood 12%. The share of sulphate pulpwood increased from 1 to 10%. The total reduction in usable wood was 6.3%. The stumpage price of the trees fell by 10.3%. As the degree of decay increased the increment percentage of the trees decreased. The most common cause of butt rot was Fomes annosus (Heterobasidion annosum) found in 46% of the number of decayed trees. Armillaria mellea was found in 16%. Bacteria were found in 50% of the decayed trees.

The PDF includes a summary in Finnish.

  • Kallio, ORCID ID:E-mail:
  • Tamminen, ORCID ID:E-mail:
article id 7572, category Article
Tauno Kallio, Pekka Tamminen. (1974). Decay of spruce (Picea abies (L.) Karst.) in the Åland Islands. Acta Forestalia Fennica no. 138 article id 7572. https://doi.org/10.14214/aff.7572

In 1972, all Norway spruce (Picea abies (L.) H. Karst.) trees of a minimum 7 cm diameter at breast height growing in the sample plots of the Sixth National Forest Inventory were examined on the main island of Aland, Finland. The soundness of standing trees was estimated by means of external characteristics and increment borer chips. The trees were then felled and measured. They were cut into lengths, and the type and extent of decay were studied.

30% of the trees examined was affected by butt rot, ca. 3% by wound decay. A comparison of the results with those of the Sixth National Forest Inventory justifies the estimate that in Aland 23% of spruce trees exceeding 7 cm in diameter at 1.3 m had butt rot.

The proportion of decayed trees in the cubic volume was 31%. Decayed wood material accounted for 5% of the volume including bark. Butt rot increased towards the mature stands. The reduction in the number of timber trees due to decay was 14.5%, in their volume 21.5%, and in the volume of sulphite pulpwood 12%. The share of sulphate pulpwood increased from 1 to 10%. The total reduction in usable wood was 6.3%. The stumpage price of the trees fell by 10.3%. As the degree of decay increased the increment percentage of the trees decreased. The most common cause of butt rot was Fomes annosus (Heterobasidion annosum) found in 46% of the number of decayed trees. Armillaria mellea was found in 16%. Bacteria were found in 50% of the decayed trees.

The PDF includes a summary in Finnish.

  • Kallio, ORCID ID:E-mail:
  • Tamminen, ORCID ID:E-mail:
article id 7562, category Article
Rihko Haarlaa. (1973). The effect of terrain on the output in forest transportation of timber. Acta Forestalia Fennica no. 128 article id 7562. https://doi.org/10.14214/aff.7562

The first part of the study includes a summary of conclusions from five earlier reports dealing with terrain transportation costs, effect of terrain, load, snow and additional machine components on the mobility of forest tractors, and the distance a vehicle has to move in forest transportation of timber. In the second part of the study the effect of these separate factors on the transport output have been analysed on the basis of simulating a transportation of 3,000 loads by computer.

It was concluded that no specific terrain factor had a dominating effect on any component of the forwarding output. However, many terrain-factor combinations with a nonsignificant effect on the mobility and also on the forwarding output were identified. The most significant factors affecting the output were the size of load and the distance driven during the cycle.

The PDF includes a summary in Finnish.

  • Haarlaa, ORCID ID:E-mail:
article id 7544, category Article
Yrjö Vuokila. (1970). Harsintaperiaate kasvatushakkuissa. Acta Forestalia Fennica no. 110 article id 7544. https://doi.org/10.14214/aff.7544
English title: Selection from above in Intermediate cuttings.

This study is concerned with silvicultural selection from above. The material consists of 18 Scots pine (Pinus sylvestris L.) sample plots in the southern half of Finland in experimental forests. The method is motivated by the great difference between the stumpage prices of saw timber and pulpwood. The method suggested includes the removal of individuals belonging to the predominating canopy, to achieve high levels of income from the stand at an early stage. The method is applied at when the growing stock is attaining saw-timber size. Before that the stand is treated with thinnings from below. It is supposed that the volume of growing stock is maintained at a level as high as that in below-thinned stands, and that rotation is of normal length.

On the average, the increment in basal area, as well as volume increment, is greater in stands selectively cut from above than in those treated with low thinnings of the same degree. Initially, selection from above seems to exert a negative effect upon the development of dominant height; later, the dominant height reassumes the same rate of increment as in the below-thinned stands. Selection from above also means an increase in saw-timber production, although it involves a reduction in the mean size of saw timber. The investigation includes growth and yield tables for pine stands treated with silvicultural selection from above.

The results of the investigation prove that silvicultural selection from above is at least as profitable as low thinning. This provides freedom for stand treatment, and contributes to the application of a method most suitable for the owner in each individual case. It is further stressed that the maintenance of a high wood capital in the stand is far more important than the method of thinning applied.

The PDF includes a summary in English.

  • Vuokila, ORCID ID:E-mail:
article id 4680, category Article
Pohjois-Suomen uitto-olojen järjestelykomitea. (1959). Pohjois-Suomen uitto-olojen järjestelykomitean mietintö. Silva Fennica no. 102 article id 4680. https://doi.org/10.14214/sf.a14123
English title: Report of the organizing committee for timber floating in Northern Finland.

Hydroelectric plants are being planned or already built in Northern Finland. The complete terracing and regulation of watercourses necessary for the power plants will mean great changes in floating conditions and hence for forestry, for which floating is the principal means of transport. Consequently, the Cabinet appointed a committee in 1958 to ascertain the economic, technical and legislative questions connected with timber transport in the area.

The committee has found that about half of the country’s forest area and two thirds of its water power resources are situated in Northern Finland. A prerequisite for the wise utilization of the forest in Northern Finland is an increase in fellings. This can only be put into effect by improving the means of transport, especially the floating channels. The financing required by the organization of floating connected with the building of the hydroelectric power plants amounts to about 10,000 million marks over a period of 20 years.

The committee has suggested that an advisory committee on floating should be established. Its most important task would be to try to produce a general programme for the organization of floating under the changed conditions, and that the State should participate in the expenditure caused by the organization as regards the capital investment needed for changing over to bundle floating.

The PDF includes a summary in English.

  • Pohjois-Suomen uitto-olojen järjestelykomitea, ORCID ID:E-mail:
article id 7603, category Article
Olli Makkonen. (1969). Ancient forestry : A historical study. Part II, The procurement and trade of forest products. Acta Forestalia Fennica no. 95 article id 7603. https://doi.org/10.14214/aff.7603

The present paper presents a study on the works of ancient writers that deal with trees, forests and the use of forests before the time of actual forest sciences. The work describes the development of knowledge pertaining to the forest and trees and the progress made on utilizing them. This second part of a series of two articles is concerned with logging, transportation and trade of timber, as well as procurement and trade of other forest products. These activities have been practiced as long as the history of mankind is known.

The article introduces the most important ancient written sources from the standpoint of the subject of the article, and related modern literature. The second part describes the texts concerning felling and primary conversion, and skidding and transportation. The third part concentrates on timber trade, and the fourth on the procurement and trade of other forest products.

  • Makkonen, ORCID ID:E-mail:
article id 4734, category Article
Yrjö Kangas. (1966). Valtion metsien hakkuupoistuma ja sen rakenne : Vuosiin 1954-1958 kohdistuva selvittely. Silva Fennica no. 120 article id 4734. https://doi.org/10.14214/sf.a14292
English title: Felling volume and its structure in the Finnish State Forests in 1954-1958 .

The purpose of this investigation was to study the felling volume and its structure in the State forests of Finland. Special attention was paid on the proportion of waste wood within the felling volume. This information was in demand for the general plan of the State forests that was being prepared at the same time. The survey was performed using a sampling method, and it represented the districts in the northernmost Finland, Ostrobothnia, Eastern Finland and Western Finland of the Forest Services.

The proportion of merchantable timber of the total felling volume was lowest in the northernmost Finland, less than 2/3 of the total cut. In Ostrobothnia the share was ¾, Eastern Finland 4/5 and in Western Finland 5/6. When the tree species were compared, the proportion of waste wood was largest in broadleaved trees, especially in the Northern Finland, while for Scots pine it was lowest. For Norway spruce the share of merchantable timber is markedly lower in the northernmost part of the country, where, for instance, decay increases the proportion of waste wood. For birch, demand of wood influences most the proportion of waste wood.

In general, the proportion of waste wood and merchantable timber in the felling volume was influenced by changes in the demand of timber, structure of the stands, and the felling method. The demand of the timber assortment affects most in the amount of waste wood. The more valuable the timber assortment is, the less waste wood is left in the cutting area.

The PDF includes a summary in German.

  • Kangas, ORCID ID:E-mail:
article id 4729, category Article
Puutavaranmittauskomitea. (1966). Puutavaranmittauskomitean mietintö : Osamietintö I. Silva Fennica no. 118 article id 4729. https://doi.org/10.14214/sf.a14287
English title: Report of timber scaling committee.

A Timber Scaling Committee was appointed by the Government of Finland in 1959, commissioned with the regulations concerning the scaling of timber and to draw a proposal for their amendments. The commission suggest revision of the regulations in their entire extent. The largest alterations should be made in the act which incorporates the provisions concerning the actual technical methods of procedure in measuring. Thus, also amendments were also posed for the Timber Scaling Law and the law concerning the scaling of timber for the purpose of paying wages.

The inclusion of the setting of the grades and quantities are considered important, since most of the disagreements occurring in measuring are concerned with quality of the timber. Inside of the sphere of application of the law would also be settling of the problems of the quality, and the measuring procedure, also when measuring for the purpose of paying wages.

According to the bill, the necessary number of official scalers and scaling boards would be appointed. The duties of the present officers would be changed. In the boards would be presented sellers, buyers, employers and employees besides the chairman. The freedom of contract in the scaling of timber will be preserved from the present law.

The report includes a bill for the Timber scaling Act, a draft for the timber scaling act, and a draft for an act which includes the timber scaling rules.

The PDF includes a summary in English.

  • Puutavaranmittauskomitea, ORCID ID:E-mail:
article id 4729, category Article
Puutavaranmittauskomitea. (1966). Puutavaranmittauskomitean mietintö : Osamietintö I. Silva Fennica no. 118 article id 4729. https://doi.org/10.14214/sf.a14287
English title: Report of timber scaling committee.

A Timber Scaling Committee was appointed by the Government of Finland in 1959, commissioned with the regulations concerning the scaling of timber and to draw a proposal for their amendments. The commission suggest revision of the regulations in their entire extent. The largest alterations should be made in the act which incorporates the provisions concerning the actual technical methods of procedure in measuring. Thus, also amendments were also posed for the Timber Scaling Law and the law concerning the scaling of timber for the purpose of paying wages.

The inclusion of the setting of the grades and quantities are considered important, since most of the disagreements occurring in measuring are concerned with quality of the timber. Inside of the sphere of application of the law would also be settling of the problems of the quality, and the measuring procedure, also when measuring for the purpose of paying wages.

According to the bill, the necessary number of official scalers and scaling boards would be appointed. The duties of the present officers would be changed. In the boards would be presented sellers, buyers, employers and employees besides the chairman. The freedom of contract in the scaling of timber will be preserved from the present law.

The report includes a bill for the Timber scaling Act, a draft for the timber scaling act, and a draft for an act which includes the timber scaling rules.

The PDF includes a summary in English.

  • Puutavaranmittauskomitea, ORCID ID:E-mail:
article id 4729, category Article
Puutavaranmittauskomitea. (1966). Puutavaranmittauskomitean mietintö : Osamietintö I. Silva Fennica no. 118 article id 4729. https://doi.org/10.14214/sf.a14287
English title: Report of timber scaling committee.

A Timber Scaling Committee was appointed by the Government of Finland in 1959, commissioned with the regulations concerning the scaling of timber and to draw a proposal for their amendments. The commission suggest revision of the regulations in their entire extent. The largest alterations should be made in the act which incorporates the provisions concerning the actual technical methods of procedure in measuring. Thus, also amendments were also posed for the Timber Scaling Law and the law concerning the scaling of timber for the purpose of paying wages.

The inclusion of the setting of the grades and quantities are considered important, since most of the disagreements occurring in measuring are concerned with quality of the timber. Inside of the sphere of application of the law would also be settling of the problems of the quality, and the measuring procedure, also when measuring for the purpose of paying wages.

According to the bill, the necessary number of official scalers and scaling boards would be appointed. The duties of the present officers would be changed. In the boards would be presented sellers, buyers, employers and employees besides the chairman. The freedom of contract in the scaling of timber will be preserved from the present law.

The report includes a bill for the Timber scaling Act, a draft for the timber scaling act, and a draft for an act which includes the timber scaling rules.

The PDF includes a summary in English.

  • Puutavaranmittauskomitea, ORCID ID:E-mail:
article id 4659, category Article
P. Piepponen. (1957). Arvo- ja rakennuspuiden merkitseminen asutustilojen metsissä. Silva Fennica no. 92 article id 4659. https://doi.org/10.14214/sf.a14060
English title: Marking of construction and other valuable timber in the forests of settlement farms.

Silva Fennica Issue 92 includes presentations held in 1956 in the 8th professional development courses, arranged for forest officers working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

Fellings of valuable timber in the forests to be surrendered for settlement farms have been discussed widely in Finland. This presentation describes the effects of the new section in the Land Settlement Decree and new directions given by Central Forestry Association Tapio based on the decree. According to the directions, the fellings have to follow legislation concerning other fellings in private forests. The felling of all large, valuable timber, as has previously been the custom in settlement farm forests, does not follow this principle.

  • Piepponen, ORCID ID:E-mail:
article id 4658, category Article
Olavi Hyttinen. (1957). Asutustilojen arvopuukysymyksestä. Silva Fennica no. 92 article id 4658. https://doi.org/10.14214/sf.a14059
English title: Valuable timber trees on settlement farms.

Silva Fennica Issue 92 includes presentations held in 1956 in the 8th professional development courses, arranged for forest officers working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

When resettlement plots have been established in Finland, a so-called household wood principle used to be used: in addition to fields, the new farm has been given forest land enough to supply it household timber. Trees larger than needed for construction of the farm were considered unnecessary, and the valuable timber trees over certain diameter could be harvested by the surrenderer of the land. This has led to fellings at minimum diameter in contrary to rational forest management. The presentation describes new legislation and directions that aim at correcting the situation.

  • Hyttinen, ORCID ID:E-mail:
article id 4658, category Article
Olavi Hyttinen. (1957). Asutustilojen arvopuukysymyksestä. Silva Fennica no. 92 article id 4658. https://doi.org/10.14214/sf.a14059
English title: Valuable timber trees on settlement farms.

Silva Fennica Issue 92 includes presentations held in 1956 in the 8th professional development courses, arranged for forest officers working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

When resettlement plots have been established in Finland, a so-called household wood principle used to be used: in addition to fields, the new farm has been given forest land enough to supply it household timber. Trees larger than needed for construction of the farm were considered unnecessary, and the valuable timber trees over certain diameter could be harvested by the surrenderer of the land. This has led to fellings at minimum diameter in contrary to rational forest management. The presentation describes new legislation and directions that aim at correcting the situation.

  • Hyttinen, ORCID ID:E-mail:
article id 4646, category Article
Paavo Yli-Vakkuri. (1955). Tutkimuksia metsänhoitolautakuntien ja -yhdistysten leimaustoiminnan kehityksestä. Silva Fennica no. 87 article id 4646. https://doi.org/10.14214/sf.a9108
English title: Studies on crop marking of District Forestry Boards and Forest Management Associations.

Wood demand and practices in the marking of trees for cutting have affected the silvicultural state of the forests of Finland in the early 1900s. The aim of the study was to study the development of timber sales and the marking of trees for logging, with a special emphasis on variation in the volume of the sales and assortment range. The study is based on statistics of the District Forestry Boards and Forest Management Associations about timber marked for cutting in 1931-1953.

The professionals in the District Forestry Boards and Forest Management Associations have marked annually in average 9 million stems of heavy timber and about 7 million m3 of stacked wood for sales. The volume  follows business cycles, the changes in the volume of stacked wood being larger than of heavy timber. When demand was high, the number of professional workers limited the supply of wood. There were large differences in the volumes marked within the country. The share of small diameter stacked wood has increased since 1930s compared to heavy timber.

The article includes a summary in German.

  • Yli-Vakkuri, ORCID ID:E-mail:
article id 4646, category Article
Paavo Yli-Vakkuri. (1955). Tutkimuksia metsänhoitolautakuntien ja -yhdistysten leimaustoiminnan kehityksestä. Silva Fennica no. 87 article id 4646. https://doi.org/10.14214/sf.a9108
English title: Studies on crop marking of District Forestry Boards and Forest Management Associations.

Wood demand and practices in the marking of trees for cutting have affected the silvicultural state of the forests of Finland in the early 1900s. The aim of the study was to study the development of timber sales and the marking of trees for logging, with a special emphasis on variation in the volume of the sales and assortment range. The study is based on statistics of the District Forestry Boards and Forest Management Associations about timber marked for cutting in 1931-1953.

The professionals in the District Forestry Boards and Forest Management Associations have marked annually in average 9 million stems of heavy timber and about 7 million m3 of stacked wood for sales. The volume  follows business cycles, the changes in the volume of stacked wood being larger than of heavy timber. When demand was high, the number of professional workers limited the supply of wood. There were large differences in the volumes marked within the country. The share of small diameter stacked wood has increased since 1930s compared to heavy timber.

The article includes a summary in German.

  • Yli-Vakkuri, ORCID ID:E-mail:
article id 4642, category Article
Einar Maliniemi. (1954). Tilastollinen tutkimus sahapuiden hakkuusta ja ajosta Perä-Pohjolassa. Silva Fennica no. 82 article id 4642. https://doi.org/10.14214/sf.a9103
English title: Statistical analysis on felling and haulage of sawlogs in Perä-Pohjola in Northern Finland.

The wages of logging and haulage has been dependent on the decisions of foremen. The aim of this study was to provide better insight on how working conditions in a logging site affect productivity of the work. Six working sites operated by Forest Service, Veitsiluoto Oy and Kemi Oy in the communes of Salla, Muonio and Kolari in Lapland were studied. The forests in the area were mostly Scots pine (Pinus sylvestris L.).

The effect of average volume of the stems, the average daily haulage over distances of various lengths, density of the stand and shape of the stem on effectivity was calculated. The size of the team was of considerable importance to the felling and haulage result in the Northern Finland where the feller assists in loading of the logs. One of the aims of the study was to find out what size of team is most advantageous for each haulage distance. The results show the optimum distance of haulage for teams of different sizes.

The article includes a summary in English.

  • Maliniemi, ORCID ID:E-mail:
article id 4631, category Article
Toivo J. Komsi. (1953). Oikeustapausten selostuksia metsänhoitajille. Silva Fennica no. 80 article id 4631. https://doi.org/10.14214/sf.a14046
English title: Forestry related legal cases for forest officers.

Silva Fennica Issue 80 includes presentations held in 1952 in the 7th professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation discusses legal cases of the supreme court of Finland that are related to forestry and handle subjects that can be of interest to forest officers working in Forest Service. The subjects vary from sale of timber to unauthorized harvest of timber.

  • Komsi, ORCID ID:E-mail:
article id 4616, category Article
Mikko Kantola. (1951). Uusimpia saavutuksia puutavaran kuljetuksen alalla. Silva Fennica no. 69 article id 4616. https://doi.org/10.14214/sf.a14012
English title: Recent achievements in timber transportation.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the development of forest haulage and long-distance transportation of timber. The article gives examples of improving the effectivity of horse hauling, use of tractors, loading of timber and floating, and gives examples of new equipment used in timber transport.

  • Kantola, ORCID ID:E-mail:
article id 4612, category Article
Veijo Heiskanen. (1951). Mäntysahatukkien laadun mukaisista arvosuhteista. Silva Fennica no. 69 article id 4612. https://doi.org/10.14214/sf.a14008
English title: Value grading of Scots pine saw logs.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

Quality grading has been rarely used in pricing of saw logs due to lack of knowledge on how the quality of logs affects the value of the sawn wood. This presentation discusses the subject based on unpublished data professor Ilmari Vuoristo collected in 1930s on effects of timber grading on the quality and value of sawn wood. The quality classification developed by professor Vuoristo is presented.

  • Heiskanen, ORCID ID:E-mail:
article id 4612, category Article
Veijo Heiskanen. (1951). Mäntysahatukkien laadun mukaisista arvosuhteista. Silva Fennica no. 69 article id 4612. https://doi.org/10.14214/sf.a14008
English title: Value grading of Scots pine saw logs.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

Quality grading has been rarely used in pricing of saw logs due to lack of knowledge on how the quality of logs affects the value of the sawn wood. This presentation discusses the subject based on unpublished data professor Ilmari Vuoristo collected in 1930s on effects of timber grading on the quality and value of sawn wood. The quality classification developed by professor Vuoristo is presented.

  • Heiskanen, ORCID ID:E-mail:
article id 4611, category Article
Veijo Heiskanen. (1951). Sahatukkien laatuluokittelulla saavutettavista eduista. Silva Fennica no. 69 article id 4611. https://doi.org/10.14214/sf.a14007
English title: Benefits of qualitative classification of saw logs.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes benefits of the qualitative classification of saw logs to forest owners and forest industry.

  • Heiskanen, ORCID ID:E-mail:
article id 4610, category Article
Veijo Heiskanen. (1951). Sahatukkien laatuluokittelutavat. Silva Fennica no. 69 article id 4610. https://doi.org/10.14214/sf.a14006
English title: Methods of saw log classification according to quality.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the uses and principles of different kinds of grading of saw logs.

  • Heiskanen, ORCID ID:E-mail:
article id 4609, category Article
F. E. Siimes. (1951). Sahatukkien laatuluokittelu sahatavarain käytön, lajittelun ja koesahausten valossa. Silva Fennica no. 69 article id 4609. https://doi.org/10.14214/sf.a14005
English title: Classification according to quality of saw logs in the light of use, grading and sawing tests of sawn timber.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the grading of sawn timber for export and domestic use, and suggests improvements to grading of the sawn products in the saw mills to better answer the needs of export.

  • Siimes, ORCID ID:E-mail:
article id 4609, category Article
F. E. Siimes. (1951). Sahatukkien laatuluokittelu sahatavarain käytön, lajittelun ja koesahausten valossa. Silva Fennica no. 69 article id 4609. https://doi.org/10.14214/sf.a14005
English title: Classification according to quality of saw logs in the light of use, grading and sawing tests of sawn timber.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the grading of sawn timber for export and domestic use, and suggests improvements to grading of the sawn products in the saw mills to better answer the needs of export.

  • Siimes, ORCID ID:E-mail:
article id 4609, category Article
F. E. Siimes. (1951). Sahatukkien laatuluokittelu sahatavarain käytön, lajittelun ja koesahausten valossa. Silva Fennica no. 69 article id 4609. https://doi.org/10.14214/sf.a14005
English title: Classification according to quality of saw logs in the light of use, grading and sawing tests of sawn timber.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the grading of sawn timber for export and domestic use, and suggests improvements to grading of the sawn products in the saw mills to better answer the needs of export.

  • Siimes, ORCID ID:E-mail:
article id 4608, category Article
V. Pöyhönen. (1951). Teollisuuden raakapuun yleiset laatuvaatimukset. Silva Fennica no. 69 article id 4608. https://doi.org/10.14214/sf.a14004
English title: General quality standards of industrial raw timber.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the development of standards for timber grades in Finland, and the present quality grades of raw timber for timber sales from state forests.

  • Pöyhönen, ORCID ID:E-mail:
article id 4608, category Article
V. Pöyhönen. (1951). Teollisuuden raakapuun yleiset laatuvaatimukset. Silva Fennica no. 69 article id 4608. https://doi.org/10.14214/sf.a14004
English title: General quality standards of industrial raw timber.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the development of standards for timber grades in Finland, and the present quality grades of raw timber for timber sales from state forests.

  • Pöyhönen, ORCID ID:E-mail:
article id 4608, category Article
V. Pöyhönen. (1951). Teollisuuden raakapuun yleiset laatuvaatimukset. Silva Fennica no. 69 article id 4608. https://doi.org/10.14214/sf.a14004
English title: General quality standards of industrial raw timber.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the development of standards for timber grades in Finland, and the present quality grades of raw timber for timber sales from state forests.

  • Pöyhönen, ORCID ID:E-mail:
article id 4608, category Article
V. Pöyhönen. (1951). Teollisuuden raakapuun yleiset laatuvaatimukset. Silva Fennica no. 69 article id 4608. https://doi.org/10.14214/sf.a14004
English title: General quality standards of industrial raw timber.

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the development of standards for timber grades in Finland, and the present quality grades of raw timber for timber sales from state forests.

  • Pöyhönen, ORCID ID:E-mail:
article id 4592, category Article
Einari Wuori. (1948). Lupakirjakauppa. Silva Fennica no. 64 article id 4592. https://doi.org/10.14214/sf.a13994
English title: Licence sales of timber in state forests.

Silva Fennica Issue 64 includes presentations held in 1947 in the third professional development courses, arranged for foresters working in the public administration. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service. Two of the presentations were published in other publications than Silva Fennica.

This presentation describes the principles of licence sales of timber in state forests. In this type of timber sales, a local forest officer has granted a licence for sale of wood or other wood products. The article gives a suggestion to improve the practices of the licence sales.

  • Wuori, ORCID ID:E-mail:
article id 4591, category Article
Aarne Anttila. (1948). Kustannusten arvioiminen hankintahakkuissa. Silva Fennica no. 64 article id 4591. https://doi.org/10.14214/sf.a13993
English title: Estimation of costs of delivery loggings.

Silva Fennica Issue 64 includes presentations held in 1947 in the third professional development courses, arranged for foresters working in the public administration. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service. Two of the presentations were published in other publications than Silva Fennica. 

This presentation describes budgeting of costs of delivery loggings, which have been at times underestimated in the practical forestry in the state forests.

  • Anttila, ORCID ID:E-mail:
article id 4591, category Article
Aarne Anttila. (1948). Kustannusten arvioiminen hankintahakkuissa. Silva Fennica no. 64 article id 4591. https://doi.org/10.14214/sf.a13993
English title: Estimation of costs of delivery loggings.

Silva Fennica Issue 64 includes presentations held in 1947 in the third professional development courses, arranged for foresters working in the public administration. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service. Two of the presentations were published in other publications than Silva Fennica. 

This presentation describes budgeting of costs of delivery loggings, which have been at times underestimated in the practical forestry in the state forests.

  • Anttila, ORCID ID:E-mail:
article id 4590, category Article
E. A. Sopanen. (1948). Hankintatöiden paikallinen organisointi. Silva Fennica no. 64 article id 4590. https://doi.org/10.14214/sf.a13992
English title: Organizing delivery loggings locally.

Silva Fennica Issue 64 includes presentations held in 1947 in the third professional development courses, arranged for foresters working in the public administration. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service. Two of the presentations were published in other publications than Silva Fennica.

This presentation outlines the history of timber sales at delivered price made in state forests, and describes good practices to arrange timber harvesting locally.

  • Sopanen, ORCID ID:E-mail:
article id 4589, category Article
V. Pöntynen. (1948). Eräitä näkökohtia metsähallituksen pysty- ja hankintamyynneistä. Silva Fennica no. 64 article id 4589. https://doi.org/10.14214/sf.a13991
English title: Aspects of sales at delivered price and stumpage sales made by Forest Service.

Silva Fennica Issue 64 includes presentations held in 1947 in the third professional development courses, arranged for foresters working in the public administration. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service. Two of the presentations were published in other publications than Silva Fennica.

This presentation compares timber sales by delivered price and stumpage sale in the state forest. The buyers of wood have criticised sales bu delivered price from the state forests. The article discusses which of the type of sales is more profitable for the state.

  • Pöntynen, ORCID ID:E-mail:
article id 4596, category Article
Valtion metsäkauppakomitea. (1948). Valtion metsien pysty- ja hankintamyynneistä : valtion metsäkauppakomitean mietintö. Silva Fennica no. 63 article id 4596. https://doi.org/10.14214/sf.a9087
English title: On stumpage sales and sales at delivered price in state forests.

The government of Finland appointed a committee to study which method of selling wood, sale at delivered price or stumpage sale, is more profitable method for wood sales from state forests.

According to the committee, in normal conditions, when supply and demand determine the price of timber and forest work wages are dependent on the supply and demand of labour, returns from the sale at delivered price has proved more favourable than stumpage sale. During the World War II the case was, however, the opposite. Sale at delivered price can have also other advantages. The state has by means of logging a hold in the labour market and can use loggings, for instance, to ward off unemployment. Also, loggings can be more easily used in rational silviculture. They keep the supervising staff of forest districts employed throughout the year and provide better professional training for the foresters. In addition, the number of buyers from state forests has increased. The stumpage sale may, however, be good method in certain conditions. The committee states that the State forestry officials are best able to decide on the most favourable method of selling.

The article includes an abstract in English.

  • Valtion metsäkauppakomitea, ORCID ID:E-mail:
article id 4581, category Article
V. Lihtonen. (1945). Metsäteollisuusyhtiöiden metsistä ja niiden hakkuista. Silva Fennica no. 61 article id 4581. https://doi.org/10.14214/sf.a9085
English title: Forests of woodworking industry and the fellings carried out in them.

The aim of this treatise is to describe forests owned by timber companies, their area and position, the quality of forests, the condition of the forests, and fellings carried out during the World War II.

Area of the company-owned forest was 1,95 million hectares, 1,64 million hectares of which was productive and 0,31 hectares inferior forest soil, not including the areas lost after the war. Most of the forests were situated in remote regions. Average volume of the tree stands was slightly larger than in farm-owned forests. Fellings counted for 84% of the growth of the forests.

During the war  the state set felling quotas for both company, private and state forests. It was widely discussed how well they were met by the different owner groups. According to the statistics, the companies had followed relatively closely their cutting plans in peace years. Cuttings were highest in 1939, when the war begun. In the war years 1940-43, lack of workforce, horses and cars for transport complicated logging. The fellings increased again during truce after Winter War. Especially demand for small timber increased during the war. Felling of firewood increased in all the owner groups, in particular in the private forests that were situated near settlements. in general fellings were higher in forests that were easiest to reach.

During the war the companies acquired timber more from their own forests. The fellings from company forests were in war years 70% of those in peace years. The article concludes that companies fulfilled the requirements as well as it was possible in the circumstances.

The article includes an abstract in English.

  • Lihtonen, ORCID ID:E-mail:
article id 4580, category Article
Johannes Virolainen. (1943). Karjalan kannaksen metsätaloudesta ja sen merkityksestä alueen pienviljelijöiden ansiotaloudessa. Silva Fennica no. 60 article id 4580. https://doi.org/10.14214/sf.a9084
English title: Forestry in the Karelian isthmus and its influence on the economy of small farms.

The article is based on studies made in the Karelian isthmus in 1936-1938 before the World War II broke in 1939. Further studies were not possible after the war when the area was handed over to Soviet Union. Economic data of agriculture and forestry of the farms had mostly been regarded separately in the early economic studies of small farms in Finland. This survey aimed at studying influence of forestry in the economy of a small farm. 141 farms were included in a more detailed survey.

Forestry accounted for in average 38% of total income of the farms in 1937-1938. The farms had sold wood often, the amounts being often small. Good transport connections in the area facilitated the sales. Over 70% were sales at delivered price, and about half of the wood was small-sized timber. According to the results of the survey, forestry was important for the small farms in Karelian isthmus. The farmers could not have made a living without the forests. Hoveter, the farms had had to overuse the forest resources. The wood resources decreased by 18-22% in 1922-1938. They were, however, at the same level as in average in Finland in 1938.

The article includes an abstract in German.

  • Virolainen, ORCID ID:E-mail:
article id 4579, category Article
Reino Kalliola. (1942). Pyhätunturin kansallispuiston kasvillisuudesta ja kasvistosta. Silva Fennica no. 59 article id 4579. https://doi.org/10.14214/sf.a9083
English title: Vegetation and flora in the Pyhätunturi National Park.

The article is based on the writer’s visits in the area in 1933 and 1939. Pyhätunturi national park was established in 1938. The fell of Pyhätunturi rises up to 540 meters above the sea level, and 357 meters above the surrounding area. The soil is predominantly stony, and the rock is quartzite. The climate is continental with low rainfall. This results in a barren area, where array of plant species is limited with the exception of few gorges with fertile river valleys. The forests have remained mostly in natural state.

Vegetation is arranged in three zones: forested area, subalpine fell birch area and alpine bare top of the fell. Scots pine (Pinus sylvestris L.) forms timberline more often than Norway spruce (Picea abies (L.) H. Karst.). Coniferous forests rise up to 365 meters on the northern slopes and up to about 385 on the southern slopes of the fell. It is followed by fell birch zone (Betula tortuosa, now Betula pubescens subsp. Czerepanovii) up to about 450-475 meters on the eastern and northern slopes, and 475-490 meters on the western slopes. The most common forest site type is Empetrum-Myrtillus site type. Herb-rich spruce swamps along the rivers have highest diversity of species. The article describes the plant species found in forests, peatlands, fell birch zone and top of the fell in detail. In all 162 different vascular plant species and 16 non-indigenous species were found in the area.

The article includes an abstract in German.

  • Kalliola, ORCID ID:E-mail:
article id 4565, category Article
Paavo Jokinen. (1939). Asutustoiminnan yhteydessä valtiolle pidätettävät arvopuut ja niiden hakkaaminen. Silva Fennica no. 52 article id 4565. https://doi.org/10.14214/sf.a13972
English title: Reservation of valuable timber-trees in connection to settlement activities.

Silva Fennica issue 52 includes presentations held in professional development courses, arranged for foresters working in public administration in 1938. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the conditions according to which the state can reclaim valuable timber-trees on forest land which ownership is transferred to landless population in settlement work.

  • Jokinen, ORCID ID:E-mail:
article id 4555, category Article
O. Seppänen. (1939). Puutavaran autokuljetuksesta ja sen merkityksestä valtion metsätaloudessa. Silva Fennica no. 52 article id 4555. https://doi.org/10.14214/sf.a13962
English title: Car transportation of roundwood and its significance to forestry in the state forests.

Silva Fennica issue 52 includes presentations held in professional development courses, arranged for foresters working in public administration in 1938. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the history of road transport of timber in Finland and discusses its significance and potential to forestry in the state forests.

  • Seppänen, ORCID ID:E-mail:
article id 4554, category Article
Ahti Mecklin. (1939). Lainsäädäntö puutavaran mittauksesta. Silva Fennica no. 52 article id 4554. https://doi.org/10.14214/sf.a13961
English title: Timber measurement legislation.

Silva Fennica issue 52 includes presentations held in professional development courses, arranged for foresters working in public administration in 1938. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the Timber Measurement Act, adopted in 1938, and its application.

  • Mecklin, ORCID ID:E-mail:
article id 4554, category Article
Ahti Mecklin. (1939). Lainsäädäntö puutavaran mittauksesta. Silva Fennica no. 52 article id 4554. https://doi.org/10.14214/sf.a13961
English title: Timber measurement legislation.

Silva Fennica issue 52 includes presentations held in professional development courses, arranged for foresters working in public administration in 1938. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the Timber Measurement Act, adopted in 1938, and its application.

  • Mecklin, ORCID ID:E-mail:
article id 4554, category Article
Ahti Mecklin. (1939). Lainsäädäntö puutavaran mittauksesta. Silva Fennica no. 52 article id 4554. https://doi.org/10.14214/sf.a13961
English title: Timber measurement legislation.

Silva Fennica issue 52 includes presentations held in professional development courses, arranged for foresters working in public administration in 1938. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the Timber Measurement Act, adopted in 1938, and its application.

  • Mecklin, ORCID ID:E-mail:
article id 4570, category Article
Paavo Jokinen. (1939). Havaintoja valtion metsämailla suoritetusta asutustyöstä. Silva Fennica no. 49 article id 4570. https://doi.org/10.14214/sf.a9073
English title: Observations on settlement in the state forests in Finland.

An act passed by the government of Finland in 1922 prescribed that state-owned forest lands will be parcelled out to landless population. A survey was made in 1934-1935 by Forest Service (Metsähallitus) to investigate the success of the establishment of settlements, and which disadvantages it may have had in forestry in the state forests. In the survey 1,194 farms were inspected.

According to the directives of settlement, the farms should be able support a family of four adults. The area of arable land was in average 5-15 hectares. In addition, the farm should have pasture and forest enough to supply it most of the household timber. According to the study, the regulations had been applied variably. Usually the farms had been given more land than was required. It was estimated that farms had been given 110,000 hectares more forest land for gathering household timber than required in the act. Many farms had sold timber, in some cases to that extent it endangered supply of household timber.

Parcelling out land had affected the management of state forests. If a region had surrendered large forest areas for settlement, it could not follow its cutting plan. Also, there was relatively little state-owned forests in southern Finland, and the effects of parcelling out land were stronger. The report concludes that in general it was not appropriate to parcel out forest land. The execution of settlement should have beeb given to Forest Service.

The article includes a German summary.

  • Jokinen, ORCID ID:E-mail:
article id 4516, category Article
M. Lappi-Seppälä. (1937). Karsimisesta arvopuun kasvatusta silmällä pitäen. Silva Fennica no. 42 article id 4516. https://doi.org/10.14214/sf.a14094
English title: Pruning as a means to produce quality timber.

 

 

  • Lappi-Seppälä, ORCID ID:E-mail:
article id 4512, category Article
Ahti Mecklin. (1937). Puutavaran kantohinnan arvioimisen perusteista. Silva Fennica no. 42 article id 4512. https://doi.org/10.14214/sf.a14090
English title: Principles of determining stumpage prices.

Silva Fennica issue 42 includes presentations held in professional development courses, arranged for foresters working in public administration in 1936. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service

This presentation describes determination of stumpage prices in timber sales of the state forests in Finland.

  • Mecklin, ORCID ID:E-mail:
article id 4500, category Article
Erkki Laitakari. (1937). Laatupuun kasvattamisesta. Silva Fennica no. 39 article id 4500. https://doi.org/10.14214/sf.a13910
English title: Production of good quality timber.

The issue 39 of Silva Fennica includes presentations held in professional development courses in 1935 that were arranged for foresters working in public administration. The presentations focus on practical issues in forest management and administration, especially in regional level.

This presentation describes methods of forest management that lead to production of qood quality timber, needed in the saw industry.

  • Laitakari, ORCID ID:E-mail:
article id 4498, category Article
Ilmari Vuoristo. (1937). Havupuumetsien laatuarvo ja laadun arviointi. Silva Fennica no. 39 article id 4498. https://doi.org/10.14214/sf.a13908
English title: Quality of coniferous forests and the value of timber.

The issue 39 of Silva Fennica includes presentations held in professional development courses in 1935 that were arranged for foresters working in public administration. The presentations focus on practical issues in forest management and administration, especially in regional level.

This presentation describes the quality of timber and coniferous forests in the point of view of saw industry.

  • Vuoristo, ORCID ID:E-mail:
article id 4498, category Article
Ilmari Vuoristo. (1937). Havupuumetsien laatuarvo ja laadun arviointi. Silva Fennica no. 39 article id 4498. https://doi.org/10.14214/sf.a13908
English title: Quality of coniferous forests and the value of timber.

The issue 39 of Silva Fennica includes presentations held in professional development courses in 1935 that were arranged for foresters working in public administration. The presentations focus on practical issues in forest management and administration, especially in regional level.

This presentation describes the quality of timber and coniferous forests in the point of view of saw industry.

  • Vuoristo, ORCID ID:E-mail:
article id 4460, category Article
I. Lassila. (1931). Suunnitelma Suomen lauttausväylillä uitetun puun uppoamisen tutkimisesta. Silva Fennica no. 19 article id 4460. https://doi.org/10.14214/sf.a9001
English title: Research proposal for studies on sinking of logs in the floating channels of Finland.

Majority of the timber floated in Finland has been floated loose. Repair of the floating channels in the end of 1800s decreased the amount of sunken logs and loss of timber during the transportation. The increase of floating of pulpwood and other small timber has later increased the number of sunken logs. More information is needed on the amount and quality of floated timber, also the floating channels should be classified. A detailed study plan to investigate how big proportion of the timber is lost during floating, which factors influence the sinking of timber, and how the timber dries in the forest depots is presented. A classification of timber by its floatability is presented.

The PDF includes a summary in German.

  • Lassila, ORCID ID:E-mail:

Register
Click this link to register for Silva Fennica submission and tracking system.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles

Committee on Publication Ethics A Trusted Community-Governed Archive