Current issue: 53(2)

Under compilation: 53(3)

Impact factor 1.683
5-year impact factor 1.950
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles containing the keyword 'vaneri'.

Category: Article

article id 7167, category Article
Veijo Heiskanen. (1966). Tutkimuksia rauduskoivikon karsimisen kannattavuudesta. Acta Forestalia Fennica vol. 81 no. 2 article id 7167. https://doi.org/10.14214/aff.7167
English title: Studies on the profitability of pruning of common birch (Betula pendula) stands.

The objective of the present investigation was to clarify the profitability of pruning silver birch (Betula verrucosa, now Betula pendula Roth) in the growing of raw material for veneer industry. Calculations were made on the grade, value, and price of pruned and untreated butt logs as well as on costs of pruning and the development of pruned trees.

The grade distribution of unpruned veneer butt logs, the grade distribution of the veneer yield, and consequently, the value of veneer yield and log prices at the plant are considerably better than those of average logs. The grade, value and price increased with increasing diameter. The value and price of pruned butt logs depended primarily on the difference between the turning pruning diameters, and their increase with decreasing pruning diameter and increasing turning diameter. The value of pruned butt logs is always considerably higher than that of unpruned logs. The increase in the value correlates to the pruning and turning diameters, and is, for example, in rotary-cut logs which have been pruned when 10 cm in diameter 80–130%.

Pruning increases the stumpage in naturally regenerated silver birch stands on Oxalis-Myrtillus site by 2,000–3,000 Fmk/ha when employed at 20 years of stand age and rotary cutting at 60–80 years of age respectively. The average pruning costs on Oxalis-Myrtillus site are 51–57 Fmk/ha.

The PDF includes a summary English.

  • Heiskanen, ORCID ID:E-mail:
article id 7167, category Article
Veijo Heiskanen. (1966). Tutkimuksia rauduskoivikon karsimisen kannattavuudesta. Acta Forestalia Fennica vol. 81 no. 2 article id 7167. https://doi.org/10.14214/aff.7167
English title: Studies on the profitability of pruning of common birch (Betula pendula) stands.

The objective of the present investigation was to clarify the profitability of pruning silver birch (Betula verrucosa, now Betula pendula Roth) in the growing of raw material for veneer industry. Calculations were made on the grade, value, and price of pruned and untreated butt logs as well as on costs of pruning and the development of pruned trees.

The grade distribution of unpruned veneer butt logs, the grade distribution of the veneer yield, and consequently, the value of veneer yield and log prices at the plant are considerably better than those of average logs. The grade, value and price increased with increasing diameter. The value and price of pruned butt logs depended primarily on the difference between the turning pruning diameters, and their increase with decreasing pruning diameter and increasing turning diameter. The value of pruned butt logs is always considerably higher than that of unpruned logs. The increase in the value correlates to the pruning and turning diameters, and is, for example, in rotary-cut logs which have been pruned when 10 cm in diameter 80–130%.

Pruning increases the stumpage in naturally regenerated silver birch stands on Oxalis-Myrtillus site by 2,000–3,000 Fmk/ha when employed at 20 years of stand age and rotary cutting at 60–80 years of age respectively. The average pruning costs on Oxalis-Myrtillus site are 51–57 Fmk/ha.

The PDF includes a summary English.

  • Heiskanen, ORCID ID:E-mail:
article id 7165, category Article
Veijo Heiskanen. (1966). Tutkimuksia koivujen vikaisuuksista, niiden vaikutuksesta sorvaustulokseen sekä niiden huomioonottamisesta laatuluokituksessa. Acta Forestalia Fennica vol. 80 no. 3 article id 7165. https://doi.org/10.14214/aff.7165
English title: Studies on the defects of birch, their influence on the quality and quantity of rotary cut veneer, and their consideration in veneer birch grading.

The objective of this paper was to study the influence of defects of Betula pendula Roth and Betula pubescens Ehrh. on the quality, value and quantity of veneer cut produced by rotary cutting, to prepare grading rules for veneer birch and to determine the minimum quality for veneer birch, and to assess the quality and quantity of veneer yield in rotary cutting of bolts of different grades. Data for the study was collected in 1953-1963 from six plywood factories in Finland.

The effect of knot marks, knot bumps, dry and rotten knots, sound knots, sweep and crookedness, upright limbs, heart rot, open and overgrown scars and bark peeling defects in the bolt on the quality and yield of veneer is described. Recommendations for grading rules were defined on the basis of the result. The rules include three grades, for which certain defects are allowed. In the first grade are accepted bolts, which of the veneer yield included at least 30% of veneer of grades A and B when all jointing and end-clipped sheets were taken into account. In the second grade were accepted bolts, which of the main part of the veneer yield still is surface veneer on the basis of the wood quality. Of the third-grade bolts at least one third of the veneer yield ought to be surface veneer.

The PDF includes a summary in English.

  • Heiskanen, ORCID ID:E-mail:
article id 7165, category Article
Veijo Heiskanen. (1966). Tutkimuksia koivujen vikaisuuksista, niiden vaikutuksesta sorvaustulokseen sekä niiden huomioonottamisesta laatuluokituksessa. Acta Forestalia Fennica vol. 80 no. 3 article id 7165. https://doi.org/10.14214/aff.7165
English title: Studies on the defects of birch, their influence on the quality and quantity of rotary cut veneer, and their consideration in veneer birch grading.

The objective of this paper was to study the influence of defects of Betula pendula Roth and Betula pubescens Ehrh. on the quality, value and quantity of veneer cut produced by rotary cutting, to prepare grading rules for veneer birch and to determine the minimum quality for veneer birch, and to assess the quality and quantity of veneer yield in rotary cutting of bolts of different grades. Data for the study was collected in 1953-1963 from six plywood factories in Finland.

The effect of knot marks, knot bumps, dry and rotten knots, sound knots, sweep and crookedness, upright limbs, heart rot, open and overgrown scars and bark peeling defects in the bolt on the quality and yield of veneer is described. Recommendations for grading rules were defined on the basis of the result. The rules include three grades, for which certain defects are allowed. In the first grade are accepted bolts, which of the veneer yield included at least 30% of veneer of grades A and B when all jointing and end-clipped sheets were taken into account. In the second grade were accepted bolts, which of the main part of the veneer yield still is surface veneer on the basis of the wood quality. Of the third-grade bolts at least one third of the veneer yield ought to be surface veneer.

The PDF includes a summary in English.

  • Heiskanen, ORCID ID:E-mail:
article id 7163, category Article
Jaakko Meriluoto. (1965). Raaka-ainetekijöiden vaikutus sorvatun koivuviilun määrään ja laatuun. Acta Forestalia Fennica vol. 80 no. 1 article id 7163. https://doi.org/10.14214/aff.7163
English title: The influence of raw material factors on the quantity and quality of rotary cut birch veneer.

The objective of the present investigation was to clarify the influence of raw material on the quantity, and especially quality of rotary cut birch veneer by running cutting tests with constant tool setting under factory conditions and with bolts of normal size. The quality of the veneer was mainly examined in laboratory.

The result showed that with an increase in bolt size the yield increases and reaches the maximal value in the diameter range of 251–275 mm and 226–250 mm for 60-inch and 50-inch bolt, respectively. With a decrease in bolt length the yield becomes higher. With the increase in the bolt size the quality of the veneer improves.

Defects in the shape of the bolt, such as crookedness, taper and oval form, decrease the yield. The good quality of the bolts affects most the yield of full-size sheets. Increase of knottiness decreases the yield by 4–5%. Lowering of the bolt temperature below 0 °C causes a sharp decline in the yield. Moisture content of the wood did not markedly affect the yield, but it improved the quality of the veneer. The minimum moisture content was 75%.

For the technical quality of the veneer, bolt temperature was the most decisive raw material factor. Also shape defects, of which crookedness was most serious, decreased the technical quality. Increase in summerwood percentage improved the quality.

The PDF includes a summary in English.

  • Meriluoto, ORCID ID:E-mail:
article id 7163, category Article
Jaakko Meriluoto. (1965). Raaka-ainetekijöiden vaikutus sorvatun koivuviilun määrään ja laatuun. Acta Forestalia Fennica vol. 80 no. 1 article id 7163. https://doi.org/10.14214/aff.7163
English title: The influence of raw material factors on the quantity and quality of rotary cut birch veneer.

The objective of the present investigation was to clarify the influence of raw material on the quantity, and especially quality of rotary cut birch veneer by running cutting tests with constant tool setting under factory conditions and with bolts of normal size. The quality of the veneer was mainly examined in laboratory.

The result showed that with an increase in bolt size the yield increases and reaches the maximal value in the diameter range of 251–275 mm and 226–250 mm for 60-inch and 50-inch bolt, respectively. With a decrease in bolt length the yield becomes higher. With the increase in the bolt size the quality of the veneer improves.

Defects in the shape of the bolt, such as crookedness, taper and oval form, decrease the yield. The good quality of the bolts affects most the yield of full-size sheets. Increase of knottiness decreases the yield by 4–5%. Lowering of the bolt temperature below 0 °C causes a sharp decline in the yield. Moisture content of the wood did not markedly affect the yield, but it improved the quality of the veneer. The minimum moisture content was 75%.

For the technical quality of the veneer, bolt temperature was the most decisive raw material factor. Also shape defects, of which crookedness was most serious, decreased the technical quality. Increase in summerwood percentage improved the quality.

The PDF includes a summary in English.

  • Meriluoto, ORCID ID:E-mail:
article id 7302, category Article
M. Lappi-Seppälä. (1934). Karsimisesta ja sen metsänhoidollisesta merkityksestä. Acta Forestalia Fennica vol. 40 no. 25 article id 7302. https://doi.org/10.14214/aff.7302
English title: The silvicultural influences of pruning.

Pruning growing trees influences tree growth and value of the wood and yield of timber of the stand. Pruning living branches create open wounds on the stems that can risk the growth of tree species that are vulnerable to injuries. For instance, pruning has been shown to cause decay in Norway spruce (Picea abies (L.) H. Karst.), while Scots pine (Pinus sylvestris L.) can quickly heal over the branch scars. Pruning of living branches reduces the crown, the effect of which remains small if only the lowest branches are pruned. Pruning of dry branches has little effect on the health of the tree. The main objective of pruning is to improve the quality of timber. Knottiness decreases strength and appearance of timber. Pruning increases the yield of knot-free sapwood, which is especially valuable in veneer timber. Pruning is, therefore, at present most suitable for birch and aspen which are used in veneer industry. In both species pruning should be directed mainly to dry branches.

The PDF includes a summary in German.

  • Lappi-Seppälä, ORCID ID:E-mail:
article id 7265, category Article
V. Pöntynen. (1931). Suomen puunjalostusteollisuuden raaka-aineen käyttö vuosina 1911-29. Acta Forestalia Fennica vol. 37 no. 3 article id 7265. https://doi.org/10.14214/aff.7265
English title: Wood consumption of wood manufacturing industry in Finland in 1911‒1929.

The main source of data was the official industrial statistics in 1911‒1929. The data was complemented with information from other sources, and the figures converted to solid volumes under bark. The wood consumption of wood manufacturing industry in the period varied strongly, being lowest in 1918 (2.2 million m3) and highest in 1927 (18.1 million m3). The wood consumption dropped during the World War I.

The wood manufacturing industry in Finland concentrated on sawmilling industry which has used annually 70‒80% of the wood consumed in the whole wood manufacturing industry. Other sectors of industry using wood were plywood industry, wood-wool industry, spool factories, match industry, mechanical pulpwood industry and pulp industry.

The PDF includes a summary in German.

  • Pöntynen, ORCID ID:E-mail:
article id 5261, category Article
Matti Kärkkäinen. (1986). Koivuvaneritukkien ja -runkojen arvosuhteet. Silva Fennica vol. 20 no. 1 article id 5261. https://doi.org/10.14214/sf.a15440
English title: Value relations of birch veneer logs and stems in Finland.

A model was developed in order to describe the peeling of veneer for determining value relationship for birch veneer logs and stems. The model was based on selling prices of veneer and other products as well as processing costs. The model was utilized for determining the effect of various input variables on the log value.

According to the results, the effect of tree size was important for the value of raw material. Even knottiness had an effect although only in the higher manufacturing costs of knotty veneer were taken into account. Pruning was a method to increase substantially the proportion of knotless veneer.

The PDF includes an abstract in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 5261, category Article
Matti Kärkkäinen. (1986). Koivuvaneritukkien ja -runkojen arvosuhteet. Silva Fennica vol. 20 no. 1 article id 5261. https://doi.org/10.14214/sf.a15440
English title: Value relations of birch veneer logs and stems in Finland.

A model was developed in order to describe the peeling of veneer for determining value relationship for birch veneer logs and stems. The model was based on selling prices of veneer and other products as well as processing costs. The model was utilized for determining the effect of various input variables on the log value.

According to the results, the effect of tree size was important for the value of raw material. Even knottiness had an effect although only in the higher manufacturing costs of knotty veneer were taken into account. Pruning was a method to increase substantially the proportion of knotless veneer.

The PDF includes an abstract in English.

  • Kärkkäinen, ORCID ID:E-mail:
article id 5018, category Article
Pertti Laakso, Olli Saikku. (1979). Havaintoja karsituista männyistä sorvatun viilun laadusta. Silva Fennica vol. 13 no. 1 article id 5018. https://doi.org/10.14214/sf.a14872
English title: Observations on the quality of veneer from pruned Scots pine stems.
Original keywords: mänty; pystykarsinta; vaneri; laatu; viilu

The material was obtained from Scots pine (Pinus sylvestris L.) stems which were pruned 27 years earlier up to the height of 5–6 m. Rotary cutting was made from 16 pruned stems and 3 unpruned ones. The length of bolts was 70 cm and the thickness of veneer 1.5 mm. The proportion of good quality veneer was 46% in pruned stems and 14% in the others. Veneer with exellent quality was obtained from pruned stems up to the height of tree meters, that is to say a little under the pruning line.
The PDF includes a summary in English.

  • Laakso, ORCID ID:E-mail:
  • Saikku, ORCID ID:E-mail:

Register
Click this link to register for Silva Fennica submission and tracking system.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles

Committee on Publication Ethics A Trusted Community-Governed Archive