Jaume Gort, Ane Zubizarreta Gerendiain, Heli Peltola, Pertti Pulkkinen, Johanna Routa, Raimo Jaatinen. (2009). Differences in fibre properties in Scots pine (Pinus sylvestris L.) genetic entries grown at different spacing and sites. Silva Fennica vol. 43 no. 3 article id 193. https://doi.org/10.14214/sf.193

Keywords: fibre length; fibre width; genetic entry; growth; wood density; coarseness; spacing

Abstract | View details | Full text in PDF | Author Info

In forest breeding, stem volume growth and sawn timber quality indicators have been used as the most important selection traits for Scots pine, whereas less attention has been given to characteristics such as fibre properties. In the above context, we investigated the differences in fibre properties (i.e. fibre length, fibre width and coarseness) in 20 year old Scots pine (Pinus sylvestris L.) genetic entries as affected by spacing and site, but also the phenotypic correlations between fibre properties, yield and wood density. The study was based on materials harvested from 10 genetic entries grown in a spacing trial (site 1) in central Finland, with a current stand density of 2000 (spacing 1), 2000–2500 (spacing 2) and 4000 trees/ha (spacing 3). In order to study the effects of site, we harvested additional material (4 of 7 genetic entries same as on site 1) from a trial located in southern Finland with a corresponding stand density of 2000 trees/ha (site 2). On site 1, spacing 1 and 3, all average values for analysed fibre properties were similar. In spacing 2 average values were slightly higher. On site 2, the average values for different fibre properties were similar compared to the corresponding spacing 1 on site 1. Spacing affected (p < 0.05) all average fibre properties on site 1; as did also site, when comparing same genetic entries grown on both sites. Regardless of spacing and site, the phenotypic correlations between average fibre length, fibre width and coarseness showed, on average, moderate to strong correlation (p < 0.05). Fibre width showed, in general, low and positive phenotypic correlation with diameter at breast height, stem volume and wood density on site 1. However, as a whole, the ranking of genetic entries changed depending on the trait and spacing considered. Thus, no overall ranking between genetic entries was possible.

Gort, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland E-mail: jaume.gort@joensuu.fi
Zubizarreta Gerendiain, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland E-mail: azg@nn.fi
Peltola, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland E-mail: hp@nn.fi
Pulkkinen, Finnish Forest Research Institute, Haapastensyrjä Breeding Station, Karkkilantie E-mail: pp@nn.fi
Routa, University of Joensuu, Faculty of Forest Sciences, FI-80101 Joensuu, Finland E-mail: jr@nn.fi
Jaatinen, Finnish Forest Research Institute, Haapastensyrjä Breeding Station, Karkkilantie E-mail: rj@nn.fi

article id 191, category Research article

Katri Luostarinen, Noora Huotari, Eila Tillman-Sutela. (2009). Effect of regeneration method on growth, wood density and fibre properties of downy birch (Betula pubescens Ehrh.). Silva Fennica vol. 43 no. 3 article id 191. https://doi.org/10.14214/sf.191

Keywords: coppice; fibre length; fibre width; regeneration methods; wood properties

Abstract | View details | Full text in PDF | Author Info

Short rotation tree stands, established by coppicing, are nowadays used mainly for energy purposes in Fennoscandia, but their usage for pulp raw material may increase in the future. Downy birch (Betula pubescens), which is commonly used for pulp production in boreal zone, has good sprouting capacity. However, it is not known if the fibre properties of sprout-originated downy birches differ from those of seed-originated ones. Therefore, fibre length and width of sprout- and seed-originated downy birches grown on fertile soil were measured at a stand age of 25 years. Additionally annual ring width, stem height and diameter, and wood density were studied to compare the growth and wood properties of sprout- and seed-originated birches. Annual rings were slightly wider in sprout- than in seed-originated birches, whereas no differences were observed in wood density. Fibres, too, were slightly longer and wider in sprout- than in seed-originated trees. Still these minor differences observed here are hardly significant for the industries using birch wood. Consequently downy birch wood from coppiced stands is well suited for pulp. The advantages of coppice, i.e. rapidity and low costs of establishment, productivity, and the ability of downy birch to grow on untypical forest sites, may even increase the importance of the wood coming from coppiced birch stands in the future.

Luostarinen, Faculty of Forest Sciences, University of Joensuu, P.O. Box 111, FI-80101, Joensuu, Finland E-mail: katri.luostarinen@joensuu.fi
Huotari, Finnish Forest Research Institute, Muhos Research Unit, Kirkkosaarentie, FI-91500 Muhos, Finland E-mail: nh@nn.fi
Tillman-Sutela, Finnish Forest Research Institute, Muhos Research Unit, Kirkkosaarentie, FI-91500 Muhos, Finland E-mail: ets@nn.fi

Click this link to register to Silva Fennica.

If you are a registered user, log in to save your selected articles for later access.

Contents alert

Your selected articles

Follow @SilvaFennica