Select issue
Silva Fennica 1926-1997
Acta Forestalia Fennica
+
1992-1999
+
1984-1991
+
1974-1983
+
1968-1973
+
1953-1968
+
1933-1952
+
1913-1932
Articles by Veli-Matti Saarinen
Category : Research article
article id 1161,
category
Research article
Tiina Laine,
Veli-Matti Saarinen.
(2014).
Comparative study of the Risutec Automatic Plant Container (APC) and Bracke planting devices.
Silva Fennica
vol.
48
no.
3
article id 1161.
https://doi.org/10.14214/sf.1161
Highlights:
As currently designed, the prototype Risutec APC fitted with an automatic feeding system offers no significant advantage over the Bracke planting device in terms of planting productivity or quality; Cost estimates suggest that an idealized automated feeding system could increase productivity and decrease unit costs.
Abstract |
Full text in HTML
|
Full text in PDF |
Author Info
The productivity of mechanized planting could be increased by minimizing the time spent manually reloading seedling cassettes. This study compared the work-time distribution, productivity and quality of the prototype Risutec APC fitted with an automatic feeding system and the commonly-used and manually-loaded Bracke P11.a. An approach of comparative time study was employed that compared performance of two operators using both machines in four sites where slash and stumps had been removed. Operating costs were estimated and compared for these two machines and an idealized machine with automatic feeding system (referred as AUT). AUT was assumed to be similar to the Bracke planting machine with the only difference being in automatic feeding. Productivity of the Risutec APC (196 seedlings per productive work hour [pl PWh0–1]) was lower than that of Bracke (244 pl PWh0–1), making the unit cost 35.7% higher. A large portion (17.6%) of the productive work time of Risutec APC was interrupted by malfunctions, so it cannot be considered robust and reliable yet. Quality of the planting work was reasonable for both machines. The results suggest that an idealized AUT could increase planting capacity (hectares per year [ha yr–1]) by 15.4% and lower the unit cost (Euro per seedling [€ pl–1]) by 4.7% compared to today’s machines. The importance of an automated feeding system increases with planting efficiency because relatively more time is spent reloading seedlings. Proper automatic feeding system could offer a cost-effective solution and could enhance productivity, but the Risutec APC has yet to meet the technical and economic standards required to be competitive.
-
Laine,
Finnish Forest Research Institute (METLA), Suonenjoki Unit, Juntintie 154, FI-77600 Suonenjoki, Finland
E-mail:
tiina.laine@metla.fi
- Saarinen, Finnish Forest Research Institute (METLA), Suonenjoki Unit, Juntintie 154, FI-77600 Suonenjoki, Finland E-mail: veli-matti.saarinen@metla.fi
article id 186,
category
Research article
Juho Rantala,
Pertti Harstela,
Veli-Matti Saarinen,
Leo Tervo.
(2009).
A techno-economic evaluation of Bracke and M-planter tree planting devices.
Silva Fennica
vol.
43
no.
4
article id 186.
https://doi.org/10.14214/sf.186
Abstract |
View details
|
Full text in PDF |
Author Info
Techno-economically reasonable mechanization of tree planting has proved to be a difficult task in the Nordic working conditions. Although planting machines and combinations of base machine and planting device have been developed since the 1970s, mechanized planting has not been cost-competitive to manual planting. The aim of this study was to find out work time distributions, productivities, costs and effects of different work difficulty factors on productivities and costs of the state-of-the-art Nordic planting devices, Swedish Bracke and Finnish M-Planter, and to compare the devices with each other. The theory of comparative time studies was the base for the experimental design of this study. In the average working conditions, productivity (E15) of M-Planter (236 seedlings/hour) was 36.0% higher than that of Bracke (174 seedlings/hour). Here, M-Planter performed planting work 23.4% cheaper than Bracke. However, the difference depended greatly on the working conditions; the more stones or stumps the smaller the difference, and the more slash the bigger the difference.
-
Rantala,
Finnish Forest Research Institute, Suonenjoki Research Unit, Juntintie 154, FI-77600 Suonenjoki, Finland
E-mail:
juho.rantala@metla.fi
- Harstela, Finnish Forest Research Institute, Suonenjoki Research Unit, Juntintie 154, FI-77600 Suonenjoki, Finland E-mail: ph@nn.fi
- Saarinen, Finnish Forest Research Institute, Suonenjoki Research Unit, Juntintie 154, FI-77600 Suonenjoki, Finland E-mail: vms@nn.fi
- Tervo, Finnish Forest Research Institute, Suonenjoki Research Unit, Juntintie 154, FI-77600 Suonenjoki, Finland E-mail: lt@nn.fi
Category : Research note
article id 10195,
category
Research note
Tiina Laine,
Leena Hamberg,
Veli-Matti Saarinen,
Timo Saksa.
(2019).
The efficacy of Chondrostereum purpureum against sprouting of deciduous species after mechanized pre-commercial thinning.
Silva Fennica
vol.
53
no.
3
article id 10195.
https://doi.org/10.14214/sf.10195
Keywords:
vegetation management;
silviculture;
mechanization;
Chondrostereum purpureum;
fungal treatment;
stump sprouts
Highlights:
Fungal treatments increased stump mortality compared to the control (cutting only); The fungal treatment did not decrease the number of sprouts per stump; Application during mechanized pre-commercial thinning did not yield as high stump mortalities as in earlier treatments performed manually.
Abstract |
Full text in HTML
|
Full text in PDF |
Author Info
The use of a white-rot fungus, Chondrostereum purpureum (Pers. Ex Fr.) Pouzar, as a biocontrol agent against sprouting has been studied with good results. The aim of the study was to investigate the efficacy of two pre-commercial thinning machines, Tehojätkä and Mense, to spread an inoculum of C. purpureum as a biocontrol agent on freshly cut birch (Betula pendula Roth and B. pubescens Ehrh.), European aspen (Populus tremula L.), rowan (Sorbus aucuparia L.), and goat willow (Salix caprea L.) stumps (the fungal treatment) and compare that to the control (cutting only, done by Tehojätkä). Efficacy was investigated in terms of stump mortality and the number of sprouts per stump. This study was conducted in one stand and sprouting was investigated for three years after treatment. The fungal treatment resulted in higher mortality of stumps (34.0% for Tehojätkä and 41.5% for Mense after three years), compared to the control (13.4%). However, the fungal treatment did not decrease the number of sprouts per stump compared to the control. The low occurrence of basidiomata indicates that the accuracy of the spreading mechanism was not satisfactory, causing low mortality figures for the fungal treatment compared to previous studies. In the future, this mechanized method may provide a promising alternative in sprout control if the spreading mechanisms, the accuracy of the treatment, and consequently the efficacy could be improved.
-
Laine,
Natural Resources Institute Finland (Luke), Natural resources, Juntintie 154, FI-77600 Suonenjoki, Finland
E-mail:
tiina.laine@luke.fi
- Hamberg, Natural Resources Institute Finland (Luke), Bioeconomy and environment, Latokartanonkaari 9, FI-00790 Helsinki, Finland E-mail: leena.hamberg@luke.fi
- Saarinen, Natural Resources Institute Finland (Luke), Natural resources, Juntintie 154, FI-77600 Suonenjoki, Finland E-mail: mulinvuori@gmail.com
- Saksa, Natural Resources Institute Finland (Luke), Natural resources, Juntintie 154, FI-77600 Suonenjoki, Finland E-mail: timo.saksa@luke.fi
Click this link to register to Silva Fennica.
If you are a registered user, log in to save your selected articles for later access.
Your selected articles
Silva Fennica ·
Finnish Society of Forest Science
