Mechanical site preparation (MSP) is a common practice that precedes the planting of Norway spruce (Picea abies (L.) H. Karst.) in Nordic forests. Mounding has become the most used method in spruce planting in recent years. This study examined the effects of different mounding treatments (spot and ditch mounding, inversion, unprepared control with or without herbicide application) and a mechanical vegetation control (MVC) treatment done 3–4 years after planting on the post-planting growth of spruce container seedlings and their development to saplings during the first 11–13 years on two forest till soils in central Finland, one on flat terrain and other on a southwest slope. On these fine-textured soils the spot and ditch mounding methods favoured spruce saplings development. Inversion and unprepared plots showed weakest growth. On the site with flat terrain, 11 years post planting, spruce saplings were 78–144 cm (38–80%) taller and their breast height diameters were 11–13 mm (60–74%) thicker for ditch or spot mounding than for inversion or herbicide treatment. On the site with sloped terrain the differences were minor between the MSP treatments. MVC improved spruce height growth on sites which did not have intensive MSP, especially on control saplings planted on unprepared soil in herbicide and inversion treatments. On the flat terrain, MVC reduced the density of resprouts to be removed later in pre-commercial thinning. As a conclusion, spot or ditch mounding favoured the growth of spruce over inversion especially on flat terrain with fine-textured soil.
In Nordic forests, consistent evidence about better seedling survival rate and increased growth due to site preparation have been obtained in numerous studies. Proper site preparation method can reduce costs of the whole regeneration chain through its effects on survival of planted seedlings, abundance of natural regeneration and competition in early stand development. This study compared the natural regeneration of birches (silver birch (Betula pendula Roth) and downy birch (B. pubescens Ehrh.)), amount of exposed mineral soil, and growth of planted seedlings between spot mounding and inverting site preparation methods. Present study was conducted in eight forest stands established in 2012 or 2015. Even though difference was not statistically significant, inverting exposed less mineral soil than spot mounding and thus reduced the natural regeneration of birch seedlings by 6135 seedlings ha–1 compared to spot mounding. However, the variation between regeneration areas was remarkable. There was no difference in seedling mortality or growth between the site preparation methods. In order to achieve high growth of conifers, moderate amount of exposed mineral soil and thus less naturally regenerated birch, inverting should be favored over spot mounding.
The aim of the study was to update the information pertaining to mechanized tree-planting activity in Finland in 2013 and its success factors. All businesses providing a mechanized tree-planting service were interviewed and asked to describe their equipment and activities, identify critical success factors (CSFs), and suggest areas for improvement. In 2013, 31 planting machines (18 Bracke P11.a, 11 M-Planter and 2 Risutec) operated by 22 businesses planted approximately 4.7 million seedlings on 2663 hectares. CSFs included expertise of planting machine operators, high quality planting, adequate amount of work, stoniness, and removal of slash. Based on the survey, some recommendations for improving mechanized planting work can be made. Firstly, improving the cost-efficiency of mechanized planting is necessary to enhance businesses’ profitability. Secondly, worksite selection is crucial as stoniness, stumps and slash debris diminish productivity. Lastly, the popularity of mechanized planting in the future will benefit from more marketing. Many businesses were unwilling to increase the area of service, invest in new equipment, or increase the volume of planting work but they believed that mechanized planting will become more popular in the near future.
The use of a white-rot fungus, Chondrostereum purpureum (Pers. Ex Fr.) Pouzar, as a biocontrol agent against sprouting has been studied with good results. The aim of the study was to investigate the efficacy of two pre-commercial thinning machines, Tehojätkä and Mense, to spread an inoculum of C. purpureum as a biocontrol agent on freshly cut birch (Betula pendula Roth and B. pubescens Ehrh.), European aspen (Populus tremula L.), rowan (Sorbus aucuparia L.), and goat willow (Salix caprea L.) stumps (the fungal treatment) and compare that to the control (cutting only, done by Tehojätkä). Efficacy was investigated in terms of stump mortality and the number of sprouts per stump. This study was conducted in one stand and sprouting was investigated for three years after treatment. The fungal treatment resulted in higher mortality of stumps (34.0% for Tehojätkä and 41.5% for Mense after three years), compared to the control (13.4%). However, the fungal treatment did not decrease the number of sprouts per stump compared to the control. The low occurrence of basidiomata indicates that the accuracy of the spreading mechanism was not satisfactory, causing low mortality figures for the fungal treatment compared to previous studies. In the future, this mechanized method may provide a promising alternative in sprout control if the spreading mechanisms, the accuracy of the treatment, and consequently the efficacy could be improved.