Current issue: 58(4)

Scopus CiteScore 2023: 3.5
Scopus ranking of open access forestry journals: 17th
PlanS compliant
Select issue
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles by Pentti Niemistö

Category : Research article

article id 23065, category Research article
Pentti Niemistö, Heikki Korpunen, Yrjö Nuutinen. (2024). Harvesting efficiency and understory damage with different cutting methods on two storied stands of silver birch and Norway spruce. Silva Fennica vol. 58 no. 2 article id 23065. https://doi.org/10.14214/sf.23065
Keywords: productivity; thinning; costs; harvesting damage; mixed stand; continuous cover; multistorey forest
Highlights: With careful, well-timed harvesting of overstory birch, it is possible to successfully use initial understory spruce in producing the next tree generation; Preserving understory spruce when cutting overstory birch reduced harvesting productivity by 30% in comparison to unpreserved harvesting; Removal of overstory birch had a positive correlation in cutting productivity but negative correlation in the quality of remaining understory spruce.
Abstract | Full text in HTML | Full text in PDF | Author Info

Uneven-aged forests set certain challenges for cut-to-length harvesting work. It is a challenge to cost-effectively remove larger trees while leaving a healthy understory for regrowth. The study’s aim was to evaluate productivity and costs of harvesting two-storied Silver birch (Betula pendula Roth) and Norway spruce (Picea abies (L.) H. Karst.) stands by creating time consumption models for cutting, and using existing models for forwarding. Damage to the remaining understory spruce was also examined. Four different harvesting methods were used: 1) all dominant birches were cut; 2) half of them thinned and understory was preserved; compared to 3) normal thinning of birch stand without understory; and 4) clear cutting of two-storied stand. Results showed the time needed for birch cutting was 26–30% lower when the understory was not preserved. Pulpwood harvesting of small sized spruces that prevent birch cutting was expensive, especially because of forwarding of small amounts with low timber density on the strip roads. Generally, when taking the cutting and forwarding into account, the unit cost at clear cuttings was lowest, due to lesser limitations on work. It was noted that with increasing removal from 100 to 300 m3 ha–1, the relative share of initial undamaged spruces after the harvest decreased from 65 to 50% when the aim was to preserve them.  During summertime harvesting, the amount of stem damage was bigger than during winter. In conclusion, two-storied stands are possible to transit to spruce stands by accepting some losses in harvesting productivity and damages on remaining trees.

  • Niemistö, Natural Resources Institute Finland (Luke), Natural resources, Kampusranta 9 C, FI-60320 Seinäjoki, Finland ORCID https://orcid.org/0000-0002-9152-2108 E-mail: ext.pentti.niemisto@luke.fi
  • Korpunen, Norsk institutt for bioøkonomi (NIBIO), Division of Forest and Forest Resources, Department of Forest operations and digitalization, Divisjon for skog og utmark, Avdeling for Driftsteknikk og digitalisering, Høgskoleveien 8, 1433 Ås, Norway ORCID https://orcid.org/0000-0001-9749-5684 E-mail: heikki.korpunen@nibio.no
  • Nuutinen, Natural Resources Institute Finland (Luke), Production systems, Yliopistokatu 6 B, FI-80100 Joensuu, Finland ORCID https://orcid.org/0000-0003-3360-4444 E-mail: yrjo.nuutinen@luke.fi (email)
article id 10512, category Research article
Mateusz Liziniewicz, Ignacio Barbeito, Andis Zvirgzdins, Lars-Göran Stener, Pentti Niemistö, Nils Fahlvik, Ulf Johansson, Bo Karlsson, Urban Nilsson. (2022). Production of genetically improved silver birch plantations in southern and central Sweden. Silva Fennica vol. 56 no. 1 article id 10512. https://doi.org/10.14214/sf.10512
Keywords: Betula pendula; planting; generalized algebraic difference approach; genetic gain; stand basal area starting function
Highlights: The basal area development of genetically improved birch in Sweden was modeled using a generalized algebraic difference approach; The best model fit, both graphically and statistically was delivered by the Korf base model; The analysis of realized gain trial showed a stability of relative differences in basal area between tested genotypes.
Abstract | Full text in HTML | Full text in PDF | Author Info

Investing in planting genetically improved silver birch (Betula pendula Roth) in Swedish plantations requires understanding how birch stands will develop over their entire rotation. Previous studies have indicated relatively low production of birch compared to Norway spruce (Picea abies (L.) Karst.) and Scots pine (Pinus sylvestris L.). This could result from using unrepresentative basic data, collected from unimproved, naturally-regenerated birch (Betula spp.) growing on inventory plots often located in coniferous stands. The objective of this study was to develop a basal area development function of improved silver birch and evaluate production over a full rotation period. We used data from 52 experiments including planted silver birch of different genetic breeding levels in southern and central Sweden. The experimental plots were established on fertile forest sites and on former agricultural lands, and were managed with different numbers of thinnings and basal area removal regimes. The model best describing total stand basal area development was a dynamic equation derived from the Korf base model. The analysis of the realized gain trial for birch showed a good stability of the early calculated relative differences in basal area between tested genotypes over time. Thus, the relative difference in basal area might be with cautious used as representation of the realized genetic gain. On average forest sites in southern Sweden, improved and planted silver birch could produce between 6–10.5 m3 ha–1 year–1, while on fertile agriculture land the average productivity might be higher, especially with material coming from the improvement program. The performed analysis provided a first step toward predicting the effects of genetic improvement on total volume production and profitability of silver birch. However, more experiments are needed to set up the relative differences between different improved material.

  • Liziniewicz, The Forestry Research Institute of Sweden, Ekebo, SE-268 90 Svalöv, Sweden E-mail: mateusz.liziniewicz@skogforsk.se
  • Barbeito, Southern Swedish Forest Research Centre, Swedish University of Agricultural Sciences, Alnarp, Sweden; Université de Lorraine, AgroParisTech, INRAE, UMR Silva, Nancy, France E-mail: ignacio.barbeito@slu.se
  • Zvirgzdins, Southern Swedish Forest Research Centre, Swedish University of Agricultural Sciences, Box 49, 23053 Alnarp, Sweden E-mail: andis.zvirgzdins@slu.se (email)
  • Stener, The Forestry Research Institute of Sweden, Ekebo, SE-268 90 Svalöv, Sweden E-mail: lg.stener@telia.com
  • Niemistö, Natural Resources In-stitute Finland (Luke), Natural resources, Seinäjoki, Finland E-mail: pentti.niemisto@luke.fi
  • Fahlvik, The Forestry Research Institute of Sweden, Ekebo, SE-268 90 Svalöv, Sweden E-mail: nils.fahlvik@skogforsk.se
  • Johansson, Tönnersjöheden Experimental Forest, SLU, Simlångsdalen, Sweden E-mail: ulf.johansson@slu.se
  • Karlsson, The Forestry Research Institute of Sweden, Ekebo, SE-268 90 Svalöv, Sweden E-mail: curly.birch@gmail.com
  • Nilsson, Southern Swedish Forest Research Centre, Swedish University of Agricultural Sciences, Box 49, 23053 Alnarp, Sweden E-mail: urban.nilsson@slu.se
article id 10052, category Research article
Pentti Niemistö, Harri Kilpeläinen, Henrik Heräjärvi. (2019). Effect of pruning season and tool on knot occlusion and stem discolouration in Betula pendula – situation five years after pruning. Silva Fennica vol. 53 no. 1 article id 10052. https://doi.org/10.14214/sf.10052
Keywords: silver birch; pruning saw; discolouration; healing-over; secateurs; stick pruning
Highlights: The occlusion was the fastest in the case of small living branches of fast growing trees pruned in springtime; Occlusion was quicker after saw pruning than after secateurs pruning, due to shorter knot stubs; Branches that were pruned in living state occluded faster than the ones pruned as dead; Dead branches hit down with a stick occluded slowly.
Abstract | Full text in HTML | Full text in PDF | Author Info

This paper investigates and models the effects of pruning season and tool on wound occlusion with varying tree and branch characteristics of silver birch (Betula pendula Roth) stems at the pruning height of 0−4 metres. Dates of eight secateurs prunings, three saw prunings and two sticks prunings as well as unpruned control were tested in permanent plots on four sites. Knot occlusion and discolouration in stemwood were measured from about 1600 studied knots of 112 sample trees felled five to six years after pruning in 2010. Knot occlusion rate was modelled according to pruning tool, date, tree growth, and branch characteristics. The occlusion was the fastest in trees pruned in spring or early summer, and the slowest in trees pruned in autumn. Stubs of living branches occluded faster than the dead ones with the same diameter. Saw pruning resulted in clearly better occlusion rates than secateurs pruning, caused by the shorter knot stubs after saw pruning. Hitting dead branches away with a stick resulted in the worst occlusion status. The colour defects spread more often upward from the knot than downward. Discolouration in stemwood was detected more frequently near to the pruned branches than the unpruned ones, and more widely near to the stubs of dead branches than the living ones. Most saw and secateurs pruned branches were completely occluded during the experiment, so these prunings were suitable for all branches under 20 mm in diameter, and for living branches even up to 30 mm in fast-growing trees.

  • Niemistö, Natural Resources Institute Finland (Luke), Natural resources, Kampusranta 9 C, FI-60320 Seinäjoki, Finland E-mail: pentti.niemisto@luke.fi (email)
  • Kilpeläinen, Natural Resources Institute Finland (Luke), Production systems, Yliopistokatu 6 B, FI-80100 Joensuu, Finland E-mail: harri.kilpelainen@luke.fi
  • Heräjärvi, Natural Resources Institute Finland (Luke), Production systems, Yliopistokatu 6 B, FI-80100 Joensuu, Finland E-mail: henrik.herajarvi@luke.fi
article id 7816, category Research article
Pentti Niemistö, Harri Kilpeläinen, Eero Poutiainen. (2018). Effect of first thinning type and age on growth, stem quality and financial performance of a Scots pine stand in Finland. Silva Fennica vol. 52 no. 2 article id 7816. https://doi.org/10.14214/sf.7816
Keywords: bucking; growth and yield; external stem quality; profitability; Pinus silvestris; tree selection; saw log
Highlights: Early commercial first thinning at the top height of 11 m with tree selection targeting high quality of remaining stems was more profitable in a Scots pine stand than thinning from below at similar time or delayed thinning 10 years later; After early first thinning only one intermediate thinning was needed, but a late thinning at age of 60 years was feasible in connection with increased amount of high quality butt logs after artificial pruning; The optimal rotation period for a Scots pine stand using a lower interest rate of 1% was 80–85 years depending on the thinning pattern. With a higher rate of 4%, the optimal rotation took only 60 years.
Abstract | Full text in HTML | Full text in PDF | Author Info

The objective of the study was to ascertain the effects of tree selection (thinning from below, from above and according to stem quality) and timing of first commercial thinning (early and delayed) on the growth, yield and quality of trees in a Scots pine (Pinus sylvestris L.) stand. A long-term field experiment (25 years) was measured in 5-year periods and the further development was simulated with growth and yield models to final cuttings using alternative rotation periods of 55–85 years. The measurements included also the exact location and type of technical defects detected on all trees in the experimental plots. The measured volume increment per unit area during the study period, 25 years after the early thinning stage was the lowest in the plots thinned from below, and the highest in the plots thinned from above or in the delayed thinning plots. However, the largest volume of saw logs during the whole rotation of 80 years was yielded after early first thinning according to the quality. The largest volume of very high-quality butt logs was produced by pruning connected with early thinning from above, and a smaller volume after early thinning according to stem quality but no after thinning from below or delayed first thinning. Without pruning an early quality thinning with one intermediate thinning was the most profitable thinning treatment in the Scots pine stand regardless the rotation length or the interest rate used. By interest rates of 1% and 2%, the optimal rotations were 80–85 years and 70 years respectively. A late thinning at the age of 60 year with long rotation was profitable only for the pruned pine stands with a low interest rate.

  • Niemistö, Natural Resources Institute Finland (Luke), Natural resources, Kampusranta 9 C, FI-60320 Seinäjoki, Finland E-mail: pentti.niemisto@luke.fi (email)
  • Kilpeläinen, Natural Resources Institute Finland (Luke), Production systems, Yliopistokatu 6, FI-80100 Joensuu, Finland E-mail: harri.kilpelainen@luke.fi
  • Poutiainen, Oulu E-mail: eero1.poutiainen@dnainternet.net
article id 2017, category Research article
Pentti Niemistö, Soili Kojola, Anssi Ahtikoski, Raija Laiho. (2017). From useless thickets to valuable resource? – Financial performance of downy birch management on drained peatlands. Silva Fennica vol. 51 no. 3 article id 2017. https://doi.org/10.14214/sf.2017
Keywords: forest management; Betula pubescens; thinning; energy wood; pulpwood; profitability; final cutting
Highlights: The most profitable management regimes for pulpwood and energy wood production in dense downy birch stands on drained peatlands include no thinnings, but final cutting at the stand age of 40–45 years as whole-tree harvesting, or as integrated harvesting of pulpwood and delimbed energy wood stems about 10 years later depending on applicable harvesting method; A competitive management regime is early precommercial thinning at 4 m dominant height to a density of 2500 stems per hectare and production of pulpwood with a rotation of 55–65 years. Equal profitability is achieved with or without traditional first thinning, which can thus be included for other reasons, for example to improve regeneration of spruce.
Abstract | Full text in HTML | Full text in PDF | Author Info

Downy birch (Betula pubescens Ehrh.) stands on drained peatlands are often considered useless because they typically do not yield good-quality sawn timber. However, covering an area of ca. 0.5 million hectares and with total yields of up to 250 m3 ha–1, downy birch stands on peatlands in Finland have a potential for pulpwood and/or energy wood production. We examined the financial performance of alternative management regimes (with or without thinnings, different thinning intensities, several rotation lengths) combined with alternative harvesting methods (pulpwood, energy wood, or integrated, energy wood being delimbed stems or whole trees). We used data from 19 experimental stands, monitored for 20–30 years. For harvesting removals we considered both actual thinning removals and final-cutting removals with alternative timings that were based on the monitoring data. We assessed the profitability as a combination of the net present value of the birch generation and the bare land value of future generations of Norway spruce (Picea abies (L.) Karst.). The most profitable management was growing without thinnings until whole-tree final cutting at the stand age of 40–45 years with an advanced multi-tree harvesting method. In contrast, the standard method in whole-tree final cutting resulted in the lowest profitability, and an integrated method with the energy wood as delimbed stems was the best of the standard methods. Thinnings were unprofitable especially when aiming to produce energy wood, whereas aiming for pulpwood, light precommercial thinning was competitive. Commercial thinning at the traditional “pulpwood stage” had little effect on profitability. The best stand age for final cutting was 40–65 years – earlier for very dense stands and whole-tree energy wood harvesting with advanced method, later for precommercially thinned stands and pulpwood harvesting.

  • Niemistö, Natural Resources Institute Finland (Luke), Management and Production of Renewable Resources, Kampusranta 9 C, 60320 Seinäjoki, Finland E-mail: pentti.niemisto@luke.fi (email)
  • Kojola, Natural Resources Institute Finland (Luke), Management and Production of Renewable Resources, Latokartanonkaari 9, 00790 Helsinki, Finland E-mail: soili.kojola@luke.fi
  • Ahtikoski, Natural Resources Institute Finland (Luke), Management and Production of Renewable Resources, Paavo Havaksentie 3, 90014 University of Oulu, Finland E-mail: anssi.ahtikoski@luke.fi
  • Laiho, Natural Resources Institute Finland (Luke), Management and Production of Renewable Resources, Latokartanonkaari 9, 00790 Helsinki, Finland E-mail: raija.laiho@luke.fi
article id 1002, category Research article
Pentti Niemistö. (2013). Effect of growing density on biomass and stem volume growth of downy birch stands on peatland in Western and Northern Finland. Silva Fennica vol. 47 no. 4 article id 1002. https://doi.org/10.14214/sf.1002
Keywords: yield; thinning; silviculture; mortality; pulpwood; stand density; crown; energy-wood
Highlights: The thinning response in young downy birch stands was low and the mortality of merchantable stems was tolerable even in dense unthinned thickets during the rotation of 50 years; The production of above-ground woody biomass and stem volume or even the production of pulpwood increased with stand density, with these values being greatest for unthinned or very lightly thinned plots.
Abstract | Full text in HTML | Full text in PDF | Author Info
The objective of the study was to ascertain the relationship of thinning intensity of downy birch (Betula pubescens Ehrh.) stands with height, crown, and diameter development as well as pulpwood, stem volume, and biomass increment using long-term (20−30 years) field experiments. Diameter growth of birches increased with thinning intensity during the first 15 years from thinning in all development phases, though after that it did so only for the youngest stands. The thinning response was low. Thinning intensity had no influence on increase in height. In terms of stem volume with bark, the mortality in unthinned stands during the study period was 30–45 m3 ha-1. The mean stem number in unthinned birch thickets fell from 25 000 ha-1 at a dominant height of 7 m to 3000 ha-1 at 18 m. The stem volume increment over the first 15 years was highest (5–6 m3 ha-1 a-1) on the very lightly thinned or unthinned plots, but later there was no significant difference between initial thinning intensities. The maximum above-ground leafless biomass (over 100 Mg ha-1) was achieved on very lightly thinned plots. Also, the total production (including thinning removal) of biomass or stem volume or even the production of pulpwood increased with stand density, with these values being greatest for very lightly thinned or unthinned plots. During 50-year rotation, the highest leafless above-ground biomass production was 2.5 Mg ha-1 a-1 as a mean value from the experiments. The highest mean annual production of pulpwood (d > 6.5 cm) was 3.2 m3 ha-1 a-1, and, in practice, no saw timber or veneer timber was produced, because of the small size and low quality of the stems. A thinning in downy birch stands increased slightly the size of stems to be removed in future cuttings, but with exception for very light thinning it decreased the production of biomass and merchantable wood.
  • Niemistö, Finnish Forest Research Institute, Parkano Unit, FI-39700 Parkano, Finland E-mail: pentti.niemisto@metla.fi (email)
article id 67, category Research article
Pentti Niemistö, Heikki Korpunen, Ari Laurén, Marika Salomäki, Jori Uusitalo. (2012). Impact and productivity of harvesting while retaining young understorey spruces in final cutting of downy birch (Betula pubescens). Silva Fennica vol. 46 no. 1 article id 67. https://doi.org/10.14214/sf.67
Keywords: Picea abies; harvesting; Betula pubescens; logging; spruce releasing
Abstract | View details | Full text in PDF | Author Info
  • Niemistö, Finnish Forest Research Institute, Parkano & Joensuu, Finland E-mail: pn@nn.fi
  • Korpunen, Finnish Forest Research Institute, Parkano & Joensuu, Finland E-mail: hk@nn.fi
  • Laurén, Finnish Forest Research Institute, Parkano & Joensuu, Finland E-mail: al@nn.fi
  • Salomäki, Finnish Forest Research Institute, Parkano & Joensuu, Finland E-mail: ms@nn.fi
  • Uusitalo, Finnish Forest Research Institute, Parkano & Joensuu, Finland E-mail: jori.uusitalo@metla.fi (email)

Register
Click this link to register to Silva Fennica.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles