Current issue: 58(5)
Articles containing the keyword 'hake'
Category : Article
A theoretical nomogram was made for estimating the costs of fully mechanized thinning and the driving speed of the machine. Based on this nomogram and the previous studies three harvesting methods were compared; systematic fully mechanized harvesting, selective fully mechanized harvesting, and manual felling combined with whole-tree chipping.
The third method was cheaper than the fully mechanized methods in a pole-stage stand. The choice of the most advantageous chipping station depended on conditions, but the smaller tree size and possibly the reduced damage on the remaining stand favour chipping on the strip road rather than chipping on the intermediate landing or at the mill.
Mechanized systematic thinning was the cheapest method for harvesting in the sapling stand. The required driving speed were so low that ergonomic factors should not hinder its use. Factors related to the future production of the stand do, however, limit its use. Mechanized selective thinning does not seem to be an economic method for harvesting in a sapling or pole-stage stand.
The PDF includes a summary in English.
-
Harstela,
E-mail:
ph@mm.unknown
- Tervo, E-mail: lt@mm.unknown
About 100 years old larch (Larix sibirica Lebed. And L. decidua Mill.) trees were felled and the basic density samples taken from the stump level were determined. The number of trees was 21 and number of samples 378. The maximum basic density was reached at the age of 40–60 years, as counted from the pith. The basic density decreased as the width of the growth rings increased or the amount of heartwood decreased. The average basic density of the whole disc was 543 kg/m3 in L. sibirica and 497 kg/m3 in L. decidua. The basic densities of bark were 328 kg/m3 and 286 kg/m3, respectively.
The PDF includes a summary in English.
-
Kärkkäinen,
E-mail:
mk@mm.unknown
In this study two methods of determining the basic density of total tree chips are compared. The method of Mäkelä (1977) is based on the volumes of Scots pine, Norway spruce, birch, and alder in a logging area, and the age of the trees. In the other method the basic density of total tree chips is measured by the common displacement method. The correlation was 0,730 in the material of 22 logging areas. Besides this it was found that the basic density of chips increases as the size of the chip particles increases with the exception of the smallest particles.
The PDF includes a summary in English.
-
Kärkkäinen,
E-mail:
mk@mm.unknown
A method is presented in this study for calculating the basic density of whole tree- and logging residue chips and the results of trial measurements on some commonly used chip sorts. The basic density of Scots pine whole tree chips was found to be 1–18 kg/m3 smaller than that of pine pulpwood of the same age. The basic density of Norway spruce whole tree chips was 4–22 kg/m3 greater than that of similar aged pulpwood. The basic density of birch whole tree chips was 4–16 kg/m3 and grey alder whole tree chips 7–24 kg/m3 greater than pulpwood of the same age. The basic density of conifer logging residue chips was considerably greater than that of pine and spruce whole tree ships.
The PDF includes a summary in English.
-
Mäkelä,
E-mail:
mm@mm.unknown
The first part of this paper consists of a study based on the available literature concerning the analysis of chip quality in the sulphate pulp process and the factors having an effect on chip quality. Using the empirical material, the suitability of the Williams chip classifier in evaluating the quality of chips made by the Algol chipper is first studied. The distribution of length and thickness of pulpwood-, long logs-, whole tree-, and logging residue chips in different conditions determined by screening is then presented.
The PDF includes a summary in English.
-
Mäkelä,
E-mail:
mm@mm.unknown
In the study the proportion of branch samples of various diameter were studied. The branches were taken from small trees to be harvested by total tree chipping method. The material consisted of 1,056 branch samples of birch (Betula verrucosa, now B. pendula Roth, and Betula pubescens Erhr.), Norway spruce (Picea abies (L.) H. Karst.) and Scots pine (Pinus sylvestris L.) at intervals of 20 cm along each branch.
With exception of the basic density of bark, there was a relation between all the other properties which were studied and the diameter. Even when the effect of diameter was eliminated, in many cases the effect of the distance of the samples from the stem became apparent.
The PDF includes a summary in English.
-
Kärkkäinen,
E-mail:
mk@mm.unknown
The paper describes a method for the measurement of basic density of total tree chips. In the method the chips are placed in a container, which is immersed in a cylinder full of water, and the container is weighted at two levels. In the upper part of the cylinder the pressure against the air bubbles is smaller than in the lower level. In this method, the effect of air bubbles in the result can be eliminated. Besides this, due to homogenization of the material to be measured only small number of samples are needed for the estimation of the average basic density.
The PDF includes a summary in English.
-
Kärkkäinen,
E-mail:
mk@mm.unknown
