Articles containing the keyword 'vikaisuus'

The present paper presents studies on the influence of some relatively common defects of Scots pine logs in Northern Finland on both the sawing yield and on the quality of the sawn goods. The study was based on test sawing of 25 logs for each of the defects (upright limb, heart shake and various kinds of wounds and scars) at Karihaara sawmill. The yield was graded into grades used for export timber according to the system of the sawmill. The proportion of the different export grades (U/S), fifths, sixths and culls) were used as characteristics together with the ratio of raw-wood consumption expressed as cu.ft/std.

Upright limbs occurring in a piece of sawn timber was shown to lower its quality to fifth grade in 43.5%, to sixth grade in 46.8% and to the category of culls in 6.5% of all cases. Only 3.2% of the cases the piece remained in U/S-grades. The size of the upright limb was the most important factor lowering the quality and affecting the ratio of raw-wood consumption.

Heart shakes are relatively common defects in pine logs deriving from over-mature trees. The quality-decreasing influence on the sawing yield depends clearly on the length of the shake in the cross-section. The same characteristics also decreases the ratio of raw-wood consumption. In addition, twisting and star shakes are considerably more harmful than straight ones. If rot occurs in connection with shakes, the places marred by the shakes are only capable of yielding sixth-grade sawn goods or culls.

Scar encountered in logs affect the sawn yield and its quality to quite a varying degree, but these defects themselves may also vary considerably both in size and quality. The length of the scar is highly significant as a quality-decreasing factor. If, in addition, rot is encountered, the defect is of a severe nature.

The PDF includes a summary in English.

• Heiskanen, E-mail: vh@mm.unknown

The aim of the present study was to find the factors influencing the distribution of Norway spruce (Picea abies (L.) H. Karst.) logs on various grades with special stress on the effects of the grade on the value of logs. The material was obtained from ten sawmills located in Southern Finland by grading a total of 13,559 logs.

The results showed that knottiness in its different forms of appearance is the most important factor influencing the quality of spruce logs. Its significance is clearly greater in spruce than in Scots pine saw logs. Among the other defects, the most common are crooks. Even scars and decay occur to a considerable degree, but other defects seldom affect the grade. The quality of butt logs is markedly better than that of top logs. Both in butt and top logs the smallest logs in diameter are of poorer quality. However, in the largest diameter classes the quality begins again to decrease.

The difference in the quality of logs of the same grade at various sawmills is very small. The results of grading at varying times at the same sawmill show greater differences than can be observed between different sawmills. However, the logs of sawmills that procure the timber from coastal areas and islands are inferior to those which procure the timber from the mainland.

The PDF includes a summary in English.

• Heiskanen, E-mail: vh@mm.unknown

The objective of this paper was to study the influence of defects of Betula pendula Roth and Betula pubescens Ehrh. on the quality, value and quantity of veneer cut produced by rotary cutting, to prepare grading rules for veneer birch and to determine the minimum quality for veneer birch, and to assess the quality and quantity of veneer yield in rotary cutting of bolts of different grades. Data for the study was collected in 1953-1963 from six plywood factories in Finland.

The effect of knot marks, knot bumps, dry and rotten knots, sound knots, sweep and crookedness, upright limbs, heart rot, open and overgrown scars and bark peeling defects in the bolt on the quality and yield of veneer is described. Recommendations for grading rules were defined on the basis of the result. The rules include three grades, for which certain defects are allowed. In the first grade are accepted bolts, which of the veneer yield included at least 30% of veneer of grades A and B when all jointing and end-clipped sheets were taken into account. In the second grade were accepted bolts, which of the main part of the veneer yield still is surface veneer on the basis of the wood quality. Of the third-grade bolts at least one third of the veneer yield ought to be surface veneer.

The PDF includes a summary in English.

• Heiskanen, E-mail: vh@mm.unknown

The different kinds of injuries in Norway spruce (Picea abies (L.) Karst.) stands was studied in 52 sample plots in Peräpohjola in the northernmost Finland. The age classes of the stands varied from 100 years to over 220 years. Most of the stands were unevenaged, as is usual in the area.

In the younger age classes (121-160 years) majority of the trees were of normal quality or had smaller injuries in all forest types. In age classes over 160 years the trees of merchantable quality decreased markedly in all forest types. The quality of the trees decreases with the age especially because of butt rot, braking of trees and crooks, forks and heart and top decay caused by the injuries. To ensure future quality it would be important that the stand is healthy from the beginning. When old spruce stands of the area are in large extent diseased by the root rot, it is questionable if they can be regenerated using natural regeneration. The spruce stands of the area are also relatively branchy. This could be prevented by growing the young stands dense. Changing the dominant tree species to Scots pine (Pinus sylvestris L.) in the dry upland forest sites could be a way to improve the quality of the forests in the area.

The PDF includes a summary in German.

• Tikka, E-mail: pt@mm.unknown

The aim of the study was to find out what are the causes of damage in Scots pine (Pinus sylvestris L.) stands and the frequency of different kinds of injuries, which are then discussed in relation to the silvicultural state and management of the stands in comparison to ideal forests. Sample plots were studied in over 80-year old Scots pine dominated stands in mineral soil sites of different forest types in Northern Finland in the area of Perä-Pohjola. 10–40 trees were chosen as sample trees in each sample plot. The sample trees were felled, and the diameter, height of crown and injuries outside and inside of the stem were recorded.

Length of knot-free part of the stem was higher in the dominant trees and in older age classes of the trees. The form of the stem becomes broader and rounder with the age. The crowns are, however, longer in Northern Finland compared to Southern Finland. In management of Scots pine stands, all trees diseased by Scots pine blister rust (Cronartium flaccidum) should be removed. The disease is common in Northern Finland, and the number of diseased trees increases as the stands get older. Decay was more common in trees that had fire wounds. In general, injuries decreased the length and diameter growth of the trees. From the dominant trees should only injured and diseased trees removed in the thinnigs. Codominant trees can be left to grow when spare trees are needed to replace missing dominant trees. Detailed instruction of selection of the removed trees are given for each age class.

The PDF includes a summary in German.

• Tikka, E-mail: pt@mm.unknown

The effect of different kinds of injuries in the amount of merchantable timber was studied in 57 sample plots in the northernmost Finland. Without any injuries the yield of timber would have been 72.3% in Scots pine (Pinus sylverstris L.) and 89.9% in Norway spruce (Picea abies (L.) H. Karst.). Butting, and removal of parts of the stems due to Injuries decreased the volume by 10.4% in pine and 13.5% in spruce. The main cause for butting of pine was fire wounds, and butt rot in spruce. Also pine blister rust (Peridermium pini and Cronartium flaccidum) causes injuries in Scots pine. The better the forest site type, the smaller is the timber discarded due to injuries. In pine 54% and in spruce 53% of the trees and were healthy. The forests in the northernmost Finland are over-mature which increase the occurrence of fire wounds and decay. Thus, forest fire control and the felling or thinning of over-mature stands will improve the quality of the timber in the long run.

The PDF includes a summary in German.

• Tikka, E-mail: pt@mm.unknown

The aim of the study was to find out what are the causes of damage in different parts of the trees and the frequency of different kinds of injuries. Sample plots were studied in over 80-year old forests in mineral soil sites and peatlands. All the trees over 1.5 m high were felled in the sample plots and the stem injuries were studied. The structure of the stand and the crown classes were recorded. The proportion of undamaged trees was largest in in dominant and codominant trees and increased towards the better forest site types. The typical injuries are listed for Scots pine (Pinus sylvestris L.), Norway spruce (Picea abies (L). H. Karst.) and Betula sp. stands. The injuries were divided in inner and outer form defects and injuries, and defined in more detail by the part of the stem and tree species. Defects caused by decay were analyzed separately.

Healing over of injuries was faster in the better sites. Form defects and other injuries were more common in birch stands than in Scots pine and Norway spruce stands. Decay was most common in birch stands. The pine stands were the healthiest, followed by spruce stands. Fire wound were most usual in pine, butt rot for spruce, and crooks and general decay for birch.

The PDF includes a summary in German.

• Tikka, E-mail: pt@mm.unknown