Articles containing the keyword 'grading'

The present paper presents studies on the influence of some relatively common defects of Scots pine logs in Northern Finland on both the sawing yield and on the quality of the sawn goods. The study was based on test sawing of 25 logs for each of the defects (upright limb, heart shake and various kinds of wounds and scars) at Karihaara sawmill. The yield was graded into grades used for export timber according to the system of the sawmill. The proportion of the different export grades (U/S), fifths, sixths and culls) were used as characteristics together with the ratio of raw-wood consumption expressed as cu.ft/std.

Upright limbs occurring in a piece of sawn timber was shown to lower its quality to fifth grade in 43.5%, to sixth grade in 46.8% and to the category of culls in 6.5% of all cases. Only 3.2% of the cases the piece remained in U/S-grades. The size of the upright limb was the most important factor lowering the quality and affecting the ratio of raw-wood consumption.

Heart shakes are relatively common defects in pine logs deriving from over-mature trees. The quality-decreasing influence on the sawing yield depends clearly on the length of the shake in the cross-section. The same characteristics also decreases the ratio of raw-wood consumption. In addition, twisting and star shakes are considerably more harmful than straight ones. If rot occurs in connection with shakes, the places marred by the shakes are only capable of yielding sixth-grade sawn goods or culls.

Scar encountered in logs affect the sawn yield and its quality to quite a varying degree, but these defects themselves may also vary considerably both in size and quality. The length of the scar is highly significant as a quality-decreasing factor. If, in addition, rot is encountered, the defect is of a severe nature.

The PDF includes a summary in English.

• Heiskanen, E-mail: vh@mm.unknown

The aim of the present study was to find the factors influencing the distribution of Norway spruce (Picea abies (L.) H. Karst.) logs on various grades with special stress on the effects of the grade on the value of logs. The material was obtained from ten sawmills located in Southern Finland by grading a total of 13,559 logs.

The results showed that knottiness in its different forms of appearance is the most important factor influencing the quality of spruce logs. Its significance is clearly greater in spruce than in Scots pine saw logs. Among the other defects, the most common are crooks. Even scars and decay occur to a considerable degree, but other defects seldom affect the grade. The quality of butt logs is markedly better than that of top logs. Both in butt and top logs the smallest logs in diameter are of poorer quality. However, in the largest diameter classes the quality begins again to decrease.

The difference in the quality of logs of the same grade at various sawmills is very small. The results of grading at varying times at the same sawmill show greater differences than can be observed between different sawmills. However, the logs of sawmills that procure the timber from coastal areas and islands are inferior to those which procure the timber from the mainland.

The PDF includes a summary in English.

• Heiskanen, E-mail: vh@mm.unknown

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation discusses accuracy of the quality grading of Scots pine (Pinus sylvestris L.) saw logs suggested by professor Ilmari Vuoristo based on a data collected by Valtiala. According to the study, greatest inaccuracies in the grading by visual inspection was caused by differences between the evaluators.

• Heiskanen, E-mail: vh@mm.unknown

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

Quality grading has been rarely used in pricing of saw logs due to lack of knowledge on how the quality of logs affects the value of the sawn wood. This presentation discusses the subject based on unpublished data professor Ilmari Vuoristo collected in 1930s on effects of timber grading on the quality and value of sawn wood. The quality classification developed by professor Vuoristo is presented.

• Heiskanen, E-mail: vh@mm.unknown

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes benefits of the qualitative classification of saw logs to forest owners and forest industry.

• Heiskanen, E-mail: vh@mm.unknown

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the uses and principles of different kinds of grading of saw logs.

• Heiskanen, E-mail: vh@mm.unknown

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the grading of sawn timber for export and domestic use, and suggests improvements to grading of the sawn products in the saw mills to better answer the needs of export.

• Siimes, E-mail: fs@mm.unknown

Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.

This presentation describes the development of standards for timber grades in Finland, and the present quality grades of raw timber for timber sales from state forests.

• Pöyhönen, E-mail: vp@mm.unknown

The objective of the present investigation was to clarify the profitability of pruning silver birch (Betula verrucosa, now Betula pendula Roth) in the growing of raw material for veneer industry. Calculations were made on the grade, value, and price of pruned and untreated butt logs as well as on costs of pruning and the development of pruned trees.

The grade distribution of unpruned veneer butt logs, the grade distribution of the veneer yield, and consequently, the value of veneer yield and log prices at the plant are considerably better than those of average logs. The grade, value and price increased with increasing diameter. The value and price of pruned butt logs depended primarily on the difference between the turning pruning diameters, and their increase with decreasing pruning diameter and increasing turning diameter. The value of pruned butt logs is always considerably higher than that of unpruned logs. The increase in the value correlates to the pruning and turning diameters, and is, for example, in rotary-cut logs which have been pruned when 10 cm in diameter 80–130%.

Pruning increases the stumpage in naturally regenerated silver birch stands on Oxalis-Myrtillus site by 2,000–3,000 Fmk/ha when employed at 20 years of stand age and rotary cutting at 60–80 years of age respectively. The average pruning costs on Oxalis-Myrtillus site are 51–57 Fmk/ha.

The PDF includes a summary English.

• Heiskanen, E-mail: vh@mm.unknown

The objective of this paper was to study the influence of defects of Betula pendula Roth and Betula pubescens Ehrh. on the quality, value and quantity of veneer cut produced by rotary cutting, to prepare grading rules for veneer birch and to determine the minimum quality for veneer birch, and to assess the quality and quantity of veneer yield in rotary cutting of bolts of different grades. Data for the study was collected in 1953-1963 from six plywood factories in Finland.

The effect of knot marks, knot bumps, dry and rotten knots, sound knots, sweep and crookedness, upright limbs, heart rot, open and overgrown scars and bark peeling defects in the bolt on the quality and yield of veneer is described. Recommendations for grading rules were defined on the basis of the result. The rules include three grades, for which certain defects are allowed. In the first grade are accepted bolts, which of the veneer yield included at least 30% of veneer of grades A and B when all jointing and end-clipped sheets were taken into account. In the second grade were accepted bolts, which of the main part of the veneer yield still is surface veneer on the basis of the wood quality. Of the third-grade bolts at least one third of the veneer yield ought to be surface veneer.

The PDF includes a summary in English.

• Heiskanen, E-mail: vh@mm.unknown

We designed a streamlined timber growth and quality model that aims at the effect of stand management on the efficiency of wood resource use. Applying the R based module toolbox to experimental plots of Douglas fir (Pseudotsuga menziesii [Mirb.] Franco) we analysed essential model features for reflecting the influence of planting density on board strength. The current version realistically predicted a significant increase of centre board bending strength at tree age 40 with initial stand density. Model performance gained clear advantage from a) parameterisation of height to diameter allometry as dependent on planting density b) consideration of cambial age and cross‑sectional knot area in board strength computation. Crown shape was less decisive. The model produced a significant effect of planting density even after a whole rotation period of 70 years as well as a realistic spectrum of board bending strength.

• Poschenrieder, Technische Universität München, Chair of Forest Growth and Yield Science, Hans Carl von Carlowitz Platz 2, 85354 Freising, Germany http://orcid.org/0000-0002-9028-8583 E-mail: Werner.Poschenrieder@lrz.tum.de
• Rais, Technische Universität München, Chair of Forest Growth and Yield Science, Hans Carl von Carlowitz Platz 2, 85354 Freising, Germany; Technische Universität München, Holzforschung München, Winzererstrasse 45, 80797 Munich, Germany E-mail: Andreas.Rais@hfm.tum.de
• van de Kuilen, Technische Universität München, Holzforschung München, Winzererstrasse 45, 80797 Munich, Germany E-mail: vandekuilen@hfm.tum.de
• Pretzsch, Technische Universität München, Chair of Forest Growth and Yield Science, Hans Carl von Carlowitz Platz 2, 85354 Freising, Germany E-mail: Hans.Pretzsch@lrz.tum.de