Articles by Veijo Heiskanen
Category : Article
The Society of Forestry in Finland (now the Finnish Society of Forest Sciences) was founded in 1909. A comprehensive history of the society has been published earlier (Acta Forestalia Fennica 40) which covers the first 50 years of is activity. The tasks of the Society are to work for the development of forestry research in Finland and to be a link between research workers in the field of forestry.
This article summarises the activity with regards of the meetings during the 60th year of the Society, and the two scientific series, Acta Forestalia Fennica and Silva Fennica, it publishes. The characteristics of the development of the publishing activity has been its’ becoming livelier and a shortening of the studies published. In 1960s funds have been granted for the execution of even larger projects. The Society has also treated many questions within the field of policy of science.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
The present paper presents studies on the influence of some relatively common defects of Scots pine logs in Northern Finland on both the sawing yield and on the quality of the sawn goods. The study was based on test sawing of 25 logs for each of the defects (upright limb, heart shake and various kinds of wounds and scars) at Karihaara sawmill. The yield was graded into grades used for export timber according to the system of the sawmill. The proportion of the different export grades (U/S), fifths, sixths and culls) were used as characteristics together with the ratio of raw-wood consumption expressed as cu.ft/std.
Upright limbs occurring in a piece of sawn timber was shown to lower its quality to fifth grade in 43.5%, to sixth grade in 46.8% and to the category of culls in 6.5% of all cases. Only 3.2% of the cases the piece remained in U/S-grades. The size of the upright limb was the most important factor lowering the quality and affecting the ratio of raw-wood consumption.
Heart shakes are relatively common defects in pine logs deriving from over-mature trees. The quality-decreasing influence on the sawing yield depends clearly on the length of the shake in the cross-section. The same characteristics also decreases the ratio of raw-wood consumption. In addition, twisting and star shakes are considerably more harmful than straight ones. If rot occurs in connection with shakes, the places marred by the shakes are only capable of yielding sixth-grade sawn goods or culls.
Scar encountered in logs affect the sawn yield and its quality to quite a varying degree, but these defects themselves may also vary considerably both in size and quality. The length of the scar is highly significant as a quality-decreasing factor. If, in addition, rot is encountered, the defect is of a severe nature.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
The aim of the present study was to find the factors influencing the distribution of Norway spruce (Picea abies (L.) H. Karst.) logs on various grades with special stress on the effects of the grade on the value of logs. The material was obtained from ten sawmills located in Southern Finland by grading a total of 13,559 logs.
The results showed that knottiness in its different forms of appearance is the most important factor influencing the quality of spruce logs. Its significance is clearly greater in spruce than in Scots pine saw logs. Among the other defects, the most common are crooks. Even scars and decay occur to a considerable degree, but other defects seldom affect the grade. The quality of butt logs is markedly better than that of top logs. Both in butt and top logs the smallest logs in diameter are of poorer quality. However, in the largest diameter classes the quality begins again to decrease.
The difference in the quality of logs of the same grade at various sawmills is very small. The results of grading at varying times at the same sawmill show greater differences than can be observed between different sawmills. However, the logs of sawmills that procure the timber from coastal areas and islands are inferior to those which procure the timber from the mainland.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
This article is a book review of a textbook ’Grundriss der Forstbenuzung. Entstehung, Eigenschaften, Verwertung und Verwendung des Holzes und anderer Forstprodukte’ by Volfgang Knigge and Horst Schulz.
-
Heiskanen,
E-mail:
vh@mm.unknown
The paper includes a short description on the publishing activity of the Society of Forestry in Finland (now the Finnish Society of Forest Science), founded in 1909, and describes the changes in the publishing of the series Acta forestalia fennica and Silva Fennica in 1967. The series Silva Fennica was changed into a quarterly starting from the beginning of 1967, at the same time, the principles of publishing was changed at least in part in favour of short reports.
The article includes an abstract in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
On the basis of time studies on pruning, one thousand stems in four stands was pruned, carried out in 1962. The work was done in two phases with Olli pruning saw, first attached to a shaft about 1.8 metres long and the to a shaft about 4 metres long.
The total time of moving from one stem to another when pruning the stem varied from 0,28 to 0.31 min per stem in the different working sites. The resting time was 19–20% of the effective working time, which included actual pruning time and the moving time. In average, 7.5% of the actual pruning time was unproductive. The actual pruning took in average 0.75–1.1 min/stem in the different sites. The time depended on size of the tree, the DBH, and on the length of the part to be pruned. The total working site time for the pruning was in average 1.34–1.98 min/stem. The output of the work per 7 hours’ working day varied from 226 to 280 stems, and the costs from 10 to 14 pennies per stem.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
The purpose of this investigation is to examine the weight and moisture of split birch fuel wood and to calculate its heat values. The weight was measured of 255 truck loads in six different locations during the winter 1959–1960. Moisture analysis was made of sample specimens collected from the loads.
The dry matter weight of the birch fuel wood was in an average 333 kg/m3 piled measure. The lowest measured weight was 319 and the highest 341 kg/m3 piled measure. The moisture content in the different parts of the pile varies distinctly. Driest wood is found in the middle of the pile. Wood in the top and bottom of the pile have about similar moisture content.
The manner of storage influences the drying process. The moisture content of open piles is 20.5%, of paper-covered piles 19.9% and roofed multiple-piles of split fuel wood 19.3%. The 2-year-old piles were dryer than 1-year-old ones. Higher percentages (25% and 20 %, respectively) than those measured in the study, are recommended for practical use. The heat value of the wood stored in a pile was in average 1,435 Mcal/m3 piled measure, and 1,455 Mcal/m3 piled measure sampled from a truck load.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.
This presentation discusses accuracy of the quality grading of Scots pine (Pinus sylvestris L.) saw logs suggested by professor Ilmari Vuoristo based on a data collected by Valtiala. According to the study, greatest inaccuracies in the grading by visual inspection was caused by differences between the evaluators.
-
Heiskanen,
E-mail:
vh@mm.unknown
Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.
Quality grading has been rarely used in pricing of saw logs due to lack of knowledge on how the quality of logs affects the value of the sawn wood. This presentation discusses the subject based on unpublished data professor Ilmari Vuoristo collected in 1930s on effects of timber grading on the quality and value of sawn wood. The quality classification developed by professor Vuoristo is presented.
-
Heiskanen,
E-mail:
vh@mm.unknown
Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.
This presentation describes benefits of the qualitative classification of saw logs to forest owners and forest industry.
-
Heiskanen,
E-mail:
vh@mm.unknown
Silva Fennica Issue 69 includes presentations held in 1948-1950 in the fourth professional development courses, arranged for foresters working in the Forest Service. The presentations focus on practical issues in forest management and administration, especially in regional level. The education was arranged by Forest Service.
This presentation describes the uses and principles of different kinds of grading of saw logs.
-
Heiskanen,
E-mail:
vh@mm.unknown
Category : Article
The objective of the present investigation was to clarify the profitability of pruning silver birch (Betula verrucosa, now Betula pendula Roth) in the growing of raw material for veneer industry. Calculations were made on the grade, value, and price of pruned and untreated butt logs as well as on costs of pruning and the development of pruned trees.
The grade distribution of unpruned veneer butt logs, the grade distribution of the veneer yield, and consequently, the value of veneer yield and log prices at the plant are considerably better than those of average logs. The grade, value and price increased with increasing diameter. The value and price of pruned butt logs depended primarily on the difference between the turning pruning diameters, and their increase with decreasing pruning diameter and increasing turning diameter. The value of pruned butt logs is always considerably higher than that of unpruned logs. The increase in the value correlates to the pruning and turning diameters, and is, for example, in rotary-cut logs which have been pruned when 10 cm in diameter 80–130%.
Pruning increases the stumpage in naturally regenerated silver birch stands on Oxalis-Myrtillus site by 2,000–3,000 Fmk/ha when employed at 20 years of stand age and rotary cutting at 60–80 years of age respectively. The average pruning costs on Oxalis-Myrtillus site are 51–57 Fmk/ha.
The PDF includes a summary English.
-
Heiskanen,
E-mail:
vh@mm.unknown
The objective of this paper was to study the influence of defects of Betula pendula Roth and Betula pubescens Ehrh. on the quality, value and quantity of veneer cut produced by rotary cutting, to prepare grading rules for veneer birch and to determine the minimum quality for veneer birch, and to assess the quality and quantity of veneer yield in rotary cutting of bolts of different grades. Data for the study was collected in 1953-1963 from six plywood factories in Finland.
The effect of knot marks, knot bumps, dry and rotten knots, sound knots, sweep and crookedness, upright limbs, heart rot, open and overgrown scars and bark peeling defects in the bolt on the quality and yield of veneer is described. Recommendations for grading rules were defined on the basis of the result. The rules include three grades, for which certain defects are allowed. In the first grade are accepted bolts, which of the veneer yield included at least 30% of veneer of grades A and B when all jointing and end-clipped sheets were taken into account. In the second grade were accepted bolts, which of the main part of the veneer yield still is surface veneer on the basis of the wood quality. Of the third-grade bolts at least one third of the veneer yield ought to be surface veneer.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
The objective of the study was to establish the influence of the founding density of a stand and the intensity of intermediate cutting on the quality of pine saw logs stems, primarily on their branchiness. Measurements were carried out in 68 Myrtillus-type and 32 Vaccinium-type Scots pine (Pinus sylvestris L.) stands. The quality of 1,982 sample trees was assessed.
According to the results, the branchless part of the stem is longest in the older age classes of trees. In all age classes the percentage of the branchless part is highest in medium sized stems. The relative height of the crown limit is greatest in small diameter classes and continues as the thickness of the tree increases. The crown is longer in the thicker tree. The grade of the butt log is on average highest in medium sized stems. Knottiness of a log made it unsuitable for a saw log only among the thickest stems. The relative share of the u/s grade decreased as the thickness of the trees increased.
From the point of view of early development of the trees it was concluded that in all age classes the branchless part is the shorter the faster the tree has grown in diameter when it was young. Also, branches of the butt log are the bigger the faster the tree has developed when it was young. The grade of the butt log improves as the thickness of the annual rings diminishes.
To produce good quality sawn timber, the pine stands should be established dense, and the first thinnings should be delayed as much as possible. The best time for the thinning would be when the diameter of the dominant trees at stump height is 12–15 cm and when all the branches have died on the length of the butt log. After the first thinning, comparatively intense intermediate thinning may be applied.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
The study examines the accuracy of volume tables for top measurement of pulpwood boles, and that of top measurement in general in Northern Finland. In this method only top diameter and length of the boles are measured, and the volume is obtained from volume tables. The boles have previously been measured in the middle of the bole, but the method is very time consuming in practice.
The result indicates that the form of both Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) Karst.) varies greatly. A pulpwood parcel, however, contains both rapidly and gently tapering logs, and the average form differences are much smaller. The difference between the real volume and the volume obtained from the volume tables is generally less than 12% and for more than third of the stock less than 4%.
Pine boles from private forests have been somewhat more and spruce boles less rapidly tapering than boles cut from state forests. The significance of the differences is not clear. Also, the boles in the northern part of the investigation area taper more sharply than those in the southern part.
It is concluded that the accuracy of the top measurement should be improved, but this is only theoretically possible by means of special tables and correction coefficients.
The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
In Finland, transportation of wood by vessels has decreased, but is still an important mode of transport especially for firewood. In 1941-1947, nearly 25% of the firewood procured by the State Fuel Board was transported by vessels. This investigation concentrates on loading of wood into barges, since the share of wages of total expenses is greatest in this phase. The loading work amounts to nearly 40% of the total wages.
Two methods of loading barges are used in Finland: loading from the shore and truck loading. This study concentrates on the more common method, loading from the shore. A time study was conducted on the different stages of loading and piling wood into barges, most of which is done by hand. Most time-consuming part of the work is transporting the logs to the barge with a wheelbarrow, comprising over 40% of the working time. Time required for loading firewood is almost twice as much as loading pulp wood. Recommendations for loading places and organization of work are given in the article to improve the efficiency of the work.
The PDF includes a summary in English.
-
Heiskanen,
E-mail:
vh@mm.unknown
