Articles containing the keyword 'K'

This study examined the relationships between forest management planning units and patches formed by forest habitat components. The test area used was a part of Koli National Park in North Karelia, eastern Finland. Forest management planning units (i.e. forest compartments) were defined by using a traditional method of Finnish forestry which applies aerial photographs and compartment-wise field inventory. Patches of forest habitat components were divided according to subjective rules by using a chosen set of variables depicting the edaphic features and vegetation of a forest habitat. The spatial distribution of the habitat components was estimated with the kriging-interpolation based on systematically located sample plots. The comparisons of the two patch mosaics were made by using the standard tools of GIS. The results of the study show that forest compartment division does not correlate very strongly with the forest habitat pattern. On average, the mean patch size of the forest habitat components is greater and the number of these patches lower compared to forest compartment division. However, if the forest habitat component distribution had been considered, the number of the forest compartments would have at least doubled after intersection.

• Uuttera, E-mail: ju@mm.unknown
• Hyppänen, E-mail: hh@mm.unknown

The study proposes a technique which enables the computation of user-defined indices for species diversity. These indices are derived from characteristics, called diversity indicators, of inventory plots, stand compartments, and the whole forest holding. The study discusses the modifications required to be made to typical forest planning systems due to this kind of biodiversity computation. A case study illustrating the use of the indices and a modified forest planning system is provided. In the case study, forest-level species diversity index was computed from the volume of dead wood, volume of broadleaved trees, area of old forest, and between-stand variety.

At the stand level, the area of old forest was replaced by stand age, and variety was described by within-stand variety. All but one of the indicators were further partitioned into two to four sub-indicators. For example, the volume of broadleaved trees was divided into volumes of birch, aspen, willow, and other tree species. The partial contribution of an indicator to the diversity index was obtained from a sub-priority function, determined separately for each indicator. The diversity index was obtained when the partial contributions were multiplied by the weights of the corresponding indicators and then were summed. The production frontiers computed for the harvested volume and diversity indices were concave, especially for the forest-level diversity index, indicating that diversity can be maintained at satisfactory level with medium harvest levels.

• Pukkala, E-mail: tp@mm.unknown
• Kangas, E-mail: jk@mm.unknown
• Kniivilä, E-mail: mk@mm.unknown
• Tiainen, E-mail: at@mm.unknown

A process-oriented tree and stand growth model is extended to be applicable to the analysis of timber quality, and how it is influenced by silvicultural treatments. The tree-level model is based on the carbon balance and it incorporates the dynamics of five biomass variables as well as tree height, crown base, and breast height diameter. Allocation of carbon is based on the conservation of structural relationships, in particular, the pipe model. The pipe-model relationships are extended to the whorl level, but in order to avoid a 3-dimensional model of entire crown structure, the branch module is largely stochastic and aggregated. In model construction, a top-down hierarchy is used where at each step down, the upper level sets constraints for the lower level. Some advantages of this approach are model consistency and efficiency of calculations, but probably at the cost of reduced flexibility. The detailed structure related with the branching module is preliminary and will be improved when more data becomes available. Model parameters are identified for Scots pine (Pinus sylvestris L.) in Southern Finland, and example simulations are carried out to compare the development of quality characteristics in different stocking densities.

• Mäkelä, E-mail: am@mm.unknown
• Ikonen, E-mail: vi@mm.unknown
• Vanninen, E-mail: pv@mm.unknown

The model HYDRA, which simulates water flow in the branched tree architecture, is characterized. Empirical studies of the last decades give strong evidence for a close structure-function linkage in the case of tree water flow. Like stomatal regulation, spatial patterns of leaf specific conductivity can be regarded as a strategy counteracting conductivity losses, which may arise under drought. Branching-oriented water flow simulation may help to understand how damaging and compensating mechanisms interact within the hydraulic network of trees. Furthermore, a coupling of hydraulic to morphological modelling is a prerequisite if water flow shall be linked to other processes. Basic assumptions of the tree water flow model HYDRA are mass conservation, Darcy's law and the spatial homogeneity of capacitance and axial conductivity. Soil water potential is given as a one-sided border condition. Water flow is driven by transpiration. For unbranched regions these principles are condensed to a nonlinear diffusion equation, which serves as a continuous reference for the discrete method tailored to the specific features of the hydraulic network. The mathematical derivation and model tests indicate that the realization of the basic assumptions is reproducible and sufficiently exact. Moreover, structure and function are coupled in a flexible and computationally efficient manner. Thus, HYDRA may serve as a tool for the comparative study of different tree architectures in terms of hydraulic function.

• Früh, E-mail: tf@mm.unknown

This article is a book review on a book ’Lodgepole pine in North America’ by Peter Koch, which is based partly on a synthesis of more than 6,000 papers on lodgepole pine, and partly on a systematic collection and analysis of wood and bark from branches, stems, stumps, and roots, as well as of foliage, of lodgepole pines.

• Hakkila, E-mail: ph@mm.unknown

The existence and direction of causal relationships between the time series for the Finnish roundwood market for the period 1960–1994 is tested. Using simple bivariate analysis, we found evidence that for both logs and pulpwood, the lagged prices are helpful in forecasting quantity for the next year, but not vice versa. Saw log stumpage prices have significantly Granger-caused pulpwood prices over the business cycles, but the effect has diminished towards the present time. For quantities traded, the direction of causality was rather from pulpwood to saw logs. The consistency of bivariate test results was checked by the Granger-causality tests within trivariate VAR-models for both markets, and the results were found to be fairly similar to bivariate tests. The price fluctuations in the international markets for forest products have been found to be carried to domestic wood markets dominantly via the pulpwood part of the market.

• Toppinen, E-mail: at@mm.unknown

Many kinds of planning systems have been labelled decision support systems (DSS), but few meet the most important features of real DSSs in planning and control of wood procurement. It has been concluded that many reasons exist to develop DSSs for wood procurement. The purchasing of timber seems to be one of the most promising areas for DSS, because there is no formal structure for these operations and decisions deal with human behaviour. Relations between DSSs and different features of the new approaches in wood procurement are also discussed, and hypotheses for future studies suggested.

• Harstela, E-mail: ph@mm.unknown

Within the European Community snow damage affects an estimated 4 million m³ of timber every year, causing significant economic losses to forest owners. In Northern Europe, for example, the occurrence of snow damage has increased over the last few decades mainly due to the increase in total growing stock. The most common form of damage is stem breakage, but trees can also be bent or uprooted. Trees suffering snow damage are also more prone to consequential damage through insect or fungal attacks.

Snow accumulation on trees is strongly dependent upon weather and climatological conditions. Temperature influences the moisture content of snow and therefore the degree to which it can accumulate on branches. Wind can cause snow to be shed, but can also lead to large accumulations of wet snow, rime or freezing rain. Wet snow is most likely in late autumn or early spring. Geographic location and topography influence the occurrence of damaging forms of snow, and coastal locations and moderate to high elevations experience large accumulations. Slope plays a less important role and the evidence on the role of aspect is contradictory. The occurrence of damaging events can vary from every winter to once every 10 years or so depending upon regional climatology. In the future, assuming global warming in northern latitudes, the risk of snow damage could increase, because the relative occurrence of snowfall near temperatures of zero could increase.

The severity of snow damage is related to tree characteristics. Stem taper and crown characteristics are the most important factors controlling the stability of trees. Slightly tapering stems, asymmetric crowns, and rigid horizontal branching are all associated with high risk. However, the evidence on species differences is less clear due to the interaction with location. Management of forests can alter risk through choice of regeneration, tending, thinning and rotation. However, quantification and comparison of the absolute effect of these measures is not yet possible. An integrated risk model is required to allow the various locational and silvicultural factors to be assessed. Plans are presented to construct such a model, and gaps in knowledge are highlighted.

• Nykänen, E-mail: mn@mm.unknown
• Broadgate, E-mail: mb@mm.unknown
• Kellomäki, E-mail: sk@mm.unknown
• Peltola, E-mail: hp@mm.unknown
• Quine, E-mail: cq@mm.unknown

Three most promising protection methods of pine pulp wood stacks against the attacks of Tomicus piniperda L. were compared. The methods were the covering of stacks by fibreglass-strengthened paper or twofold achrylene netting, removing the upper parts of stacks, and enhanced planning of the placement of the timber store using ARC/INFO GIS-software. T. piniperda was observed to strongly prefer the upper parts of the stacks: 90 % of the beetles occurred within 0.5 meters of the top of the stacks. Covering of the stacks decreased the attack density of T. piniperda, and the protection effect of covering was 80 %. Due to long transport distances and fragmentation of forest landscape the relocation of timber store was found to be an unsuitable method in the practical level. Also, taking into account the costs of the method, removing of the upper parts of stacks was considered to be the optimal solution.

• Jääskelä, E-mail: mj@mm.unknown
• Heliövaara, E-mail: kh@mm.unknown
• Peltonen, E-mail: mp@mm.unknown
• Saarenmaa, E-mail: hs@mm.unknown

Distribution and occurrence of bark beetles and other forest insects in relation to environmental variation were analysed by multivariate methods. Eight different forest edges were studied using 10 x 10 m sample plots that formed 200 m linear transects perpendicular to the forest edge. Forest edge affected the distribution of insect species only in the edges between mature, non-managed spruce stands and clear cuts or young seedling stands, but not in the pine stands. The occurrence of the selected forest insects mainly depended on variables associated with the amount and quality of suitable woody material. The most significant environmental variables were forest site type, crown canopy coverage, tree species, number of stumps, number of dead spruce trunks and amount of logging waste at site. Quantitative classification of species and sample plots showed that some specialized species (Xylechinus pilosus, Cryphalus saltuarius, Polygraphus poligraphus and P. subopacus) adapted to mature spruce forests, tended to withdraw from the forest edge to interior stand sites. By contrast many generalized species (Pityogenes chalcographus, P. quadridens, Pissodes spp., Hylurgops palliatus, Tomicus piniperda, Dryocoetes spp. and Trypodendron lineatum) benefitted from cuttings and spread over stand borders into mature forest.

• Peltonen, E-mail: mp@mm.unknown
• Heliövaara, E-mail: kh@mm.unknown
• Väisänen, E-mail: rv@mm.unknown

The purpose of this article was to collate the literature on fungal diseases that occur on seedlings in forest nurseries. It describes the symptoms of the diseases, the infection pattern of each fungus and the possibilities of controlling the diseases. As background a short introduction is given on forests and nursery practices in Finland.

• Lilja, E-mail: al@mm.unknown
• Kurkela, E-mail: tk@mm.unknown
• Lilja, E-mail: sl@mm.unknown
• Rikala., E-mail: rr@mm.unknown

Four governmental efforts are underway to reach consensus on indicators of sustainable forestry. Through the Helsinki process, European countries have developed and reached a pan-European, binding consensus, The Montreal process includes non-European Temperate and boreal forest countries, the International Tropical Timber Organization (lTTO) have developed guidelines for the sustainable management of natural tropical forests, and the countries around the Amazon basis have developed a joint initiative for creating guidelines of sustainable forest management of the Amazonian tropical rain forests. It is estimated that as many as 15–20 distinct processes are under way in the private sector by non-profit organizations and for-profit companies, some domestic and other international in scope. Perhaps the most wide-ranging definition work of non-governmental organizations is the undertake by the Forest Stewardship Council, FSC. The paper discusses the Helsinki and Montreal processes and the tasks for research.

• Parviainen, E-mail: jp@mm.unknown

The horizontal and vertical stand structure of living trees was examined in a managed and in a primeval Norway spruce-dominated forest in Southern Finland. Tree size distributions (DBHs, tree height) were compared using frequency histograms. The vertical distribution of tree heights was illustrated as tree height plots and quantified as the tree height diversity (THD) using the Shannon-Weaver formula. The horizontal spatial pattern of trees was described with stem maps and quantified with Ripley's K-function. The spatial autocorrelation of tree sizes was examined with semivariogram analysis. In the managed forest the DBH and height distributions of trees were bimodal, indicating a two-layered vertical structure with a single dominant tree layer and abundant regeneration in the understory. The primeval forest had a much higher total number of trees which were rather evenly distributed in different diameter and tree height classes. The K-function summaries for trees taller than 15 m indicated that the primeval stand was close to complete random pattern. The managed stand was regular at small distances (up to 4 m). The semivariograms of tree sizes (DBH tree height) showed that the managed forest had a clear spatial dependence in tree sizes up to inter-tree distances of about 12 meters. In contrast, the primeval spruce forest had a variance peak at very short inter-tree distances (< 1 m) and only weak spatial autocorrelation at short inter-tree distances (1–5 m). Excluding the understory trees (h < 15 m) from the analysis drastically changed the spatial structure of the forest as revealed by semivariograms. ln general, the structure of the primeval forest was both horizontally and vertically more variable and heterogeneous compared to the managed forest. The applicability of the used methods in describing fine-scale forest structure i discussed.

• Kuuluvainen, E-mail: tk@mm.unknown
• Leinonen, E-mail: kl@mm.unknown
• Nygren, E-mail: mn@mm.unknown
• Penttinen, E-mail: ap@mm.unknown

There is no doubt that tree survival, growth, and reproduction in North America's boreal forests would be directly influenced by the projected changes in climate if they occur. The indirect effects of climate change may be of even greater importance, however, because of their potential for altering the intensity, frequency, and perhaps even the very nature of the disturbance regimes which drive boreal forest dynamics. Insect defoliator populations are one of the dominating disturbance factors in North America's boreal forests and during outbreaks trees are often killed over vast forest areas. If the predicted shifts in climate occur, the damage patterns caused by insects may be considerably changed, particularly those of insects whose temporal and spatial distributions are singularly dependent on climatic factors. The ensuing uncertainties directly affect depletion forecasts, pest hazard rating procedures, and long-term planning for pest control requirements. Because the potential for wildfire often increases in stands after insect attack, uncertainties in future insect damage patterns also lead to uncertainties in fire regimes. In addition, because the rates of processes key to biogeochemical and nutrient recycling are influenced by insect damage, potential changes in damage patterns can indirectly affect ecosystem resilience and the sustainability of the multiple uses of the forest resource.

In this paper, a mechanistic perspective is developed based on available information describing how defoliating forest insects might respond to climate warming. Because of its prevalence and long history of study, the spruce budworm, Choristoneura fumiferana Clem. (Lepidoptera: Tortricidae), is used for illustrative purposes in developing this perspective. The scenarios that follow outline the potential importance of threshold behaviour, historical conditions, phenological relationships, infrequent but extreme weather, complex feedbacks, and natural selection. The urgency of such considerations is emphasized by reference to research suggesting that climate warming may already be influencing some insect lifecycles.

• Fleming, E-mail: rf@mm.unknown

A gap-model was used with forest inventory data in taking ground-true site, soil and tree characteristics into account in predicting the effects of climate change on forests. A total of 910 permanent sample plots established in the course of national forest inventory (NFI) in Finland and located on mineral soil sites in southern Finland were selected as the input data. The climatological input used in the simulations consisted of interpolated means of and deviations from long-term local temperature and precipitation records. The policy-oriented climate scenarios of SILMU (Finnish Research Programme on Climate Change) were used to describe the climate change. The temperature changes in the climate scenarios were increases of ca. +1.1 °C (low), +4.4 °C (medium) and +6.6 °C (high) compared to the current climate in 110 years. The simulation period was 110 years covering the time years 1990–2100.

Southern Finland, divided into fifteen forestry board districts, was used as the study region. Regional development of stand volume, cutting yield, and total wood production of forests under different climate scenarios were examined. The annual average growth in simulations under current climate was close to that observed in NFL Forests benefited from a modest temperature increase (Scenario 2), but under Scenario 1 the growing stock remained at a lower level than under the current climate in all parts of the study region. In wood production and cutting yield there were regional differences. In the southern part of the study regional wood production under Scenario 1 was ca. 10% lower than under the current climate, but in the eastern and western parts wood production was 5–15% higher under Scenario 1 than under the current climate. The relative values of total wood production and cutting yield indicated that the response of forests to climate change varied by geographical location and the magnitude of climate change. This may be a consequence of not just varying climatic (e.g. temperature and precipitation) and site conditions, but of varying responses by different kind of forests (e.g. forests differing in tree species composition and age).

• Talkkari, E-mail: at@mm.unknown

Investigations carried out in the Kola peninsula (northern taiga) and in the South-western part of Western Siberia (southern taiga and forest-steppe) revealed identical course of the postfire restoration process of forest litter thickness in Scots pine (Pinus sylvestris L.) forests. Despite the differences in mean annual temperature (2°C) and other climatic characteristics the recovery time for thickness of forest litter in both regions amounts to 90–100 years after fire in pine forests of lichen site type and 120–140 years – in green moss type; the thickness of forest litter therewith corresponds 3–4 cm and 7–8 cm respectively. That mean that within the natural borders of pine forests, communities of a specific type possess uniform characteristics of restoration. On the basis of empirical data, it appears that the predicted increase of mean annual temperature of earth surface by (2°C) will not bring changes into the character of postfire recovery of forest litter thickness. It was shown that during the period of the recovery, which spans about 90 years after fire in pine forests of lichen and green moss-lichen site types and 140 years in ones of green moss site types, the rate of increasing of carbon store in the forest litter averaged 0.6 t ha^-1 year^-1, 0.1 t ha^-1 year^-1 and 0.2 t ha^-1 year^-1, respectively.

• Gorshkov, E-mail: vg@mm.unknown
• Bakkal, E-mail: ib@mm.unknown
• Stavrova, E-mail: ns@mm.unknown

The European Pine Sawfly (Neodiprion sertifer Geoffroy) is one of the most serious defoliators of Scots pine (Pinus sylvestris L.) in northern Europe. We studied the pattern in the regional occurrence of the outbreaks of N. sertifer in Finland in years 1961-90, and made predictions about the outbreak pattern to the year 2050 after predicted winter warming. We tested whether minimum winter temperatures and forest type and soil properties could explain the observed outbreak pattern. We analysed outbreak patterns at two different spatial levels: forest board- and municipal-level.

The proportion of coniferous forests on damage-susceptible soils (dry and infertile sites) explained a significant part of the variation in outbreak frequency at small spatial scale (municipalities) but not at large spatial scale (forest boards). At the forest board level, the incidence of minimum temperatures below -36 °C (= the critical value for egg mortality) explains 33% of the variation in the outbreak pattern, and at the municipal level the incidence of cold winters was also the most significant explaining variable in northern Finland. Egg mortality due to cold winters seems to be the most parsimonious factor explaining why there have been so few N. sertifer outbreaks in northern and north-eastern Finland. We predict that climate change (increased winter temperatures) may increase the frequency of outbreaks in eastern and northern Finland in the future.

• Virtanen, E-mail: tv@mm.unknown
• Neuvonen, E-mail: sn@mm.unknown
• Niemelä, E-mail: pn@mm.unknown
• Nikula, E-mail: an@mm.unknown
• Varama, E-mail: mv@mm.unknown

In the winter of 1977/78, a White-backed Woodpecker (Dendrocopos leucotos Bechstein) was observed in the archipelago of southwestern Finland 200 km from its breeding areas. It foraged on insects living in mall dead alder and birches. The potential prey species were identified by rearing the insects from the trunks used by the White-backed Woodpecker. Altogether 628 adult insects emerged. In addition to the big larvae the potential food also included larvae of Sciaridae and Cecidomyidae (Diptera) living in dense clumps.

• Nuorteva, E-mail: mn@mm.unknown
• Saari, E-mail: ls@mm.unknown

Time studies and an ergonomic assessment were carried out in logging operations for three logging machines based on backhoe loader chassis. The time studies were completed with a follow-up study of one backhoe loader-based single-grip harvester. The studies indicated a productivity at the same level as that of specialized Nordic logging machines. Ergonomics also proved to be good. Mean ground pressure exerted by the backhoe loader-based logging machines was little higher than for some of the conventional Nordic single-grip harvesters to which it was compared. The ability of the machines to operate in the terrain was also good, even in rough terrain.

These machines can also be used for other jobs, such as ditch digging, road building and road maintenance. The machines then function more as carriers for attachments rather than custom-built backhoe loaders. By more careful planning of operations, the machines can be used to a higher degree and more effectively. The relatively low investment cost compared to many custom-built Nordic logging machines also contributes to a reduction of operating costs.

• Johansson, E-mail: jj@mm.unknown

The aim of the study was to compare the behaviour of three selected provenances of Eucalyptus microtheca F. Muell. that were likely to respond differently to drought. For this purpose, we studied the effects of vapour pressure deficit and soil water content on leaf water potential in an irrigated plantation in Bura, eastern Kenya.

An international provenance trial of Eucalyptus microtheca, established as a part of Finnida-supported Bura Forestry Research Project in eastern Kenya in 1984 was used as a plant material in the study. The eastern provenance showed generally the lowest leaf water potential on a daily basis. Statistically significant differences in the daily leaf water potential fluctuations were detected. The eastern provenance exhibited the greatest and the northern one the smallest values. The minimum daily leaf water potential of the provenances responded well to changes in gravimetric soil water content, the western provenance being the most sensitive one. The relationship of the observed results and annual rainfall distribution in the geographic regions of the studied provenances is discussed.

• Tuomela, E-mail: kt@mm.unknown
• Kanninen, E-mail: mk@mm.unknown

In this study, logistic regression and neural networks were used to predict non-industrial private forests (NIPF) landowners’ choice of forest taxation basis. The main frame of reference of the study was the Finnish capital taxation reform of 1993. As a consequence of the reform, landowners were required to choose whether to be taxed according to site-productivity or realized-income during the coming transition period of thirteen years.

The most important factor affecting the landowners’ choice of taxation basis was the harvest rate during the transition period, i.e. the chosen timber management strategy. Furthermore, the estimated personal marginal tax rate and the intention to cut timber during next three years affected the choice. The descriptive landowner variables did not have any marked effect on the choice of forest taxation basis.

On average, logistic regression predicted 71% of the choices correctly; the corresponding figure for neural networks was 63%. In both methods, the choice of site-productivity taxation was predicted more accurately than the choice of realized-income taxation. An increase in the number of model variable did not significantly improve the results of neural networks and logistic regression.

• Pesonen, E-mail: mp@mm.unknown
• Kettunen, E-mail: ak@mm.unknown
• Räsänen, E-mail: pr@mm.unknown

The biomass production and nutrient uptake of silver birch (Betula pendula Roth), downy birch (Betula pubescens Erhr.), grey alder (Alnus incana (L.) Moench), native willows Salix triandra L. and S. phylicifolia L. and exotic willows S. x dasyclados and S. ’Aquatica’ growing on a clay mineral soil field (Sukeva) and on two cut-away peatland areas (Piipsanneva, Valkeasuo) were investigated.

Biomass production of downy birch was greater than that of silver birch, and the biomass production of the native willows greater than that of the exotic ones. The performance of S. phylicifolia was the best of the studied willow species. Exotic willows were susceptible to frost damage and their winter hardiness was poor. The production of all species was lower on the clay mineral soil field than on the cut-away peatland areas. Fertilization of birches and alder – on the double dose given to the willows – increased biomass production. After 6 growing seasons the leafless biomass production of fertilized silver birch at Piipsanneca was 21 t ha^-1 (at Valkeasuo 34 t ha^-1) and of grey alder 24 t ha^-1, and that of S. triandra after five growing seasons 31 t ha^-1, S. phylicifolia 38 t ha^-1 and of S. x dasyclados 16 t ha^-1.

6-year-old stands of silver birch bound more nutrients per unit biomass than downy birch stands. Grey alder bound more N, Ca and Co but less Mn and Zn per unit biomass than silver and downy birch. On the field more P was bound in grey alder per unit biomass compared to downy birch. The willows had more K per unit biomass than the other tree species, and the exotic willow species more N than the native ones. Less N, K and Mg were bound per unit biomass of S. phylicifolia compared to the other tree species.

• Hytönen, E-mail: jh@mm.unknown
• Rossi, E-mail: pr@mm.unknown
• Saarsalmi, E-mail: as@mm.unknown

This article is a book review on a book on forest inventory, ’Sampling Methods for Multiresource Forest Inventory’ by Hans T. Schreuder, Timothy G. Gregoire and Geoffrey B. Wood.

• Köhl, E-mail: mk@mm.unknown

Relationships between bulk density and organic matter (OM) content, textural properties and depth are described for forested mineral soils from Central and Northern Finland. Core samples were taken of 0–5, 30–35 and 60–65 cm layers at 75 plots. Three measures of bulk density were calculated: the bulk density of the < 20 mm fraction (BD₂₀), the bulk density of the < 2 mm fraction (BD₂), and laboratory bulk density (BD_l). BD_l was determined from the mass of a fixed volume of < 2 mm soil taken in the laboratory. All three measures of bulk densities were strongly correlated with organic matter content (r ≥ -0.63). Depth and gravel (2–20 mm) content (in the case of BD₂) were also important variables. BD_l was sensitive to clay contents > 7% but did significantly improve the prediction of both BD₂ and BD₂₀ in coarse soils (clay contents ≤ 7%). Predictive models were derived for coarse soils.

• Tamminen, E-mail: pt@mm.unknown
• Starr, E-mail: ms@mm.unknown

In the method presented in this study, a group of experts evaluate, in a pairwise manner, a set of forest areas with respect to the game species considered. On the basis of these comparisons, relative priorities of forest areas are estimated using the eigenvalue technique. Using regression analysis, a habitat suitability function is estimated in which the priority is predicted by measures already familiar in forest planning. As a case study, a habitat suitability function was estimated for black grouse (Tetrao tetrix, Lururus tetrix L.). The function is applicable in forestry planning carried out using modern planning techniques.

The PDF includes an abstract in Finnish.

• Kangas, E-mail: jk@mm.unknown
• Karsikko, E-mail: jk@mm.unknown
• Laasonen, E-mail: ll@mm.unknown
• Pukkala, E-mail: tp@mm.unknown

The paper discusses the principles of forest management in the state forests of Finland, and the contradictions in choosing between the different land uses. These principles of the forest management are sustainable use of natural resources, economic and effective management, and taking in account nature conservation, protection of environment, recreation services and employment issues in all activities of the Forest Service. Even regional policy affects the management planning in the state forests.

• Kotimäki, E-mail: tk@mm.unknown

Forests have been economically important for Finnish private forest owners at all times, but the use of forests has changed markedly since 1920s, when forests were mainly used for collecting household timber, and the cuttings were often exploitative because of the farmer’s need for money. The present situation is totally different. Need for household timber is marginally small, and private forestry produces mainly timber for sale. The sales of timber have increased, but due to better forest management the growing stock in the private forests has increased. The article discusses how the changes in values of forest owners has and will affect the stage of private forestry.

• Järveläinen, E-mail: vj@mm.unknown

The paper discusses how the general trend towards increasing growth and productivity in the European societies is expressed also in forestry. It is reflected, for instance, in the increasing production and productivity of forest industries. Technological progress and call for economic growth require great flexibility from all resources. These pressures for effectiveness and production also concern Finnish forestry and forest management. Industrialization, urbanization and development of forestry have increased the pressure to use forests in recreation, preserving human environment and nature conservation in addition to production of timber. Through the development the definition of sustainability has become wider.

• Vehkamäki, E-mail: sv@mm.unknown

The paper deals with the application of forest dynamics. Reference is made to two studies, which have been carried out at a national level. The simulations of forest decline as well as the production of exceedingly thick timber of spruce and fir provide various examples of the major problems of forest simulation and of some possible solutions. It is pointed out that the statistical analysis of empirical data is most important for modelling and it might bring about even more valuable results than the ultimate simulation itself.

• Sekot, E-mail: ws@mm.unknown

Europe’s forest area has increased 5 million ha since the late 1960s. The growing stock has increased 43% and the net annual increment 55% in exploitable forests since 1950. A part of the reported increase is caused by sampling inventories, which have been made in greater part of the countries. Sampling inventories have corrected earlier underestimates of the growing stock and the increment.

The difference between the annual net increment and fellings has increased since 1950. The net increment, 584 million m³, exceeded fellings, 408 million m³, by 176 million m³, in exploitable forests in 1990. If fellings could be increased to equal the increment, Europe would be an exporter of forest products.

A greater increase in the density, in the age and in the mean volume of forests per hectare threaten the biological stability of the growing stock. Degrading of the stock, increasing natural losses and deteriorating environmental qualities of forests can only be prevented by increased fellings and by forest regeneration.

The PDF includes an abstract in Finnish.

• Kuusela, E-mail: kk@mm.unknown

A model for the mechanism of windfall and stem breakage was constructed for single Scots pine (Pinus sylvestris L.) at the stand edge. The total turning moment arising from the wind drag and from the bending of stem and crown was calculated along with the breaking stress of the stem. Similarly, the support given by the root -soil plate anchorage was calculated. Windspeed variation within the crown and the vertical distribution of stem and crown weight were taken into account. Model computations showed that trees having a large height to diameter ratio were subjected to greater risk of falling down or breaking than trees with a small height to diameter ratio. The windspeed required to blow down a tree or break the stem of a tree decreased if the height to diameter ratio or the crown to stem ratio of trees increased.
The PDF includes an abstract in Finnish.

• Peltola, E-mail: hp@mm.unknown
• Kellomäki, E-mail: sk@mm.unknown

The water retention characteristics and their variation in tree nurseries and related physical properties were determined for commercially produced growth media made of light slightly humified Sphagnum peat. A total of 100 samples of peat media were collected from filled seedling trays in the greenhouses of four Finnish nurseries in 1990. In addition, the physical properties were determined for two growth media made of compressed peat sheets and chips. The variation in water retention characteristics in nurseries was described using linear models with fixed and random effects. The sources of variation in the mixed linear models were producer, grade, batch (greenhouse) and sample (tray).

The water retention of the peat media at different matric potentials was comparable to that given in the literature. The media shrank an average of 0–16% during desorption. The peat grades were finer than the Nordic quality standards for peat growth media. Particles < 1 mm increased and particles 1–5 mm decreased the water retention characteristics measured. The greatest total variation in water retention was at -1 kPa. The water retention of the peat media differed least at -5 and -10 kPa. The water retention characteristics of media from different producers usually differed significantly. The grades, on the other hand, did not differ from each other in their water retention characteristics nor were there significant interactions between producer and grade. The batch effect was marked but was lower than the effect within batches, where the sample (tray) effect was greater than the effect due to random measurement error. At -10 kPa, the measurement error was, however, clearly greater than the sample effect. The random measurement error was comparable to the batch effect. Aeration of the growth media is dependent on the water content retained between saturation and -1 kPa. The water availability to seedlings at the nursery phase is affected mainly by water retention between -1 and -10 kPa.
The PDF includes an abstract in Finnish.

• Heiskanen, E-mail: jh@mm.unknown

The matric potential and unsaturated hydraulic conductivity of peat-based growth media in containers was measured continuously as a function of drying. The particle size distribution and the water retention characteristics of the media were determined from parallel samples. The growth media used were a light, coarse graded Sphagnum peat, a medium graded Sphagnum peat and a mixture of a perlite and the medium graded Sphagnum peat. Containers of two types were packed with the media and allowed to evaporate from saturation. Matric potential was measured automatically using tensiometers during drying.

In both container types, the matric potential of the media was similar down to 10 kPa at each of the three levels measured during drying. Further drying resulted in a large matric potential gradient between the upper and the middle levels. During drying, there was also clear shrinkage of the media. When the matric potential at the upper level reached ca. -80 kPa, the decrease in height of the media was 5–23 %. The estimated hydraulic conductivity of the media during drying was rather similar. The hydraulic conductivity of the peat-perlite mixture was, however, slightly lower than that of the pure peat media. The hydraulic conductivity decreased linearly on a log-log-scale from ca. 10^-5 to less than 10^-10 m/s as the matric potential decreased from -3 to -60 kPa. The hydraulic conductivity of the media was comparable to coarse sand at matric potentials below -10 kPa. The decrease in hydraulic conductivity during drying and the possible weakening of soil-root contact due to shrinkage may considerably affect the availability of water to plants.
The PDF includes an abstract in Finnish.

• Heiskanen, E-mail: jh@mm.unknown

The aim of the study was to describe the total change of forest area in non-industrial private forest holdings in southeast Finland, 1986–1991. The average gross decrease of forest area was 1.7 hectares, whereas the average gross increase was 1.2 hectares. Consequently, the average size of holdings decreased from 32.5 to 32.0 hectares. The most important factors affecting the changes of forest area were the inheritance system, resulting in a decrease of 0.7 ha, and reclassification of forestry land, producing an increase of 0.4 ha per holding. The increase of small, under 10 ha holdings accounted for much of the structural change.

The PDF includes an abstract in English.

• Ripatti, E-mail: pr@mm.unknown

This article summarises the importance of forest industry in the acquisition and consumption of wood-based energy in Finland. Opportunities to increase the efficiency of energy utilization further are discussed, as well.

The forest industry uses 25% of the total energy and 40% of the total electricity. It also generates considerable amounts of heat and electric power as by-products of wood-processing. Wood in different forms accounts for 64% of the fuels of the forest industry. Consequently, the need for outside, imported energy is minute. Black liquor of pulping is dominant as a source of wood-based energy. In addition, plenty of wood residues (bark, saw dust, planer shavings, grinder dust, screening reject of chips) and minor amounts of for wood processing unsuitable fractions obtained in conjunction with harvesting small-sized whole-trees, tree selections and logging residues are used for energy production.

The PDF includes an abstract in Finnish.

• Verkasalo, E-mail: ev@mm.unknown

Speed and load sizes presented in three study reports on sulky skidding were compared with estimates based on ergonomic models. Speed and load size estimates were closely correlated with the observed values, when a 400 W energy expenditure of the subject was used. This corresponds to less than half of his submaximal oxygen intake and matches well with the heart rate given in one of the time studies. It seems possible to develop methods for evaluating the work pace/production rate for sulky skidding in varying terrain conditions.

The PDF includes an abstract in Finnish.

• Saarilahti, E-mail: ms@mm.unknown

This article is a book review on a German book ’Die Fichte’ by H. Schmidt-Vogt, summarizing the knowledge of the genus Picea and its 36 species.

• Leikola, E-mail: ml@mm.unknown

The main stem of young Scots pine (Pinus sylvestris L.) trees was cut off halfway along the current leading shoot and the two previous years’ leading shoots to simulate moose (Alces alces) damage. Trees of the same size were chosen as controls before treatments. The experiment was inspected ten years after artificial stem breakage. Removing the current leading shoot and the second shoot did not essentially affect the height and diameter growth of the trees. Removal down to the third shoot reduced the height as well as diameter growth. The average loss in growth was equivalent to less than one year’s growth. When the stem was cut off at the second or third shoot, stem crookedness and the presence of knots resulted in stem defects that will subsequently reduce the sawtimber quality. A high proportion of the stem defects will obviously still be visible at the first thinning cutting. Removing injured trees as pulpwood and pruning the remaining parts of cut stems evidently improves the quality of pine stand with moose damage.

The PDF includes an abstract in Finnish.

• Heikkilä, E-mail: rh@mm.unknown
• Löyttyniemi, E-mail: kl@mm.unknown

During the past 30 years, genetics research has accumulated much information on black spruce (Picea mariana). The adoption of less intensive and faster plustree selection, establishment of seedling seed orchards and family selection significantly increased the rate of progress in improvement of the species. In New Brunswick this approach made it possible to obtain substantial quantities of seeds 10 years after the initiation of the program, and now all the seeds used in reforestation are derived from seed orchards.

Fourteen years after beginning the black spruce breeding program, second generation breeding is underway. The possibility of implementing alternative breeding strategies using ”breeding – cloning” procedures are explored for the advanced generation. Until somatic embryogenesis techniques become fully operational, ”backward selection” schemes and crossing in breeding halls followed by vegetative multiplication using serial rooted cuttings can be adopted. Larger genetic gains than those from conventional breeding are expected not only from the utilization of both additive and non-additive variances, but also from the elimination of inefficiencies of large conventional seed orchards.

• Morgenstern, E-mail: em@mm.unknown
• Park, E-mail: yp@mm.unknown

The profitability of forestry in the context of recent economic developments in Finland suggest a more systematic analysis of the profit and the cost structure of small-scale forestry than is normally made today. The domestic and international pressure on farming emphasizes the development of rural areas by means of other business than agriculture, in practice this may mean forestry. Financing in terms of the new law concerning agriculture requires projects to be profitable. Thus, the profitability of different lines of production, including forestry, needs to be reported more carefully than is the practice today.

A network of forestry bookkeeping farms covering the whole Austria has existed for 20 years. The organization and the operation of the forestry bookkeeping and the cost accounting system is based on the scientific cooperation and exchange of information between the organizations in charge. The practical experience and recommendations based thereon might be useful for Finland, when implementing a country-wide network of forestry bookkeeping and cost accounting.

The PDF includes an abstract in English.

• Penttinen, E-mail: mp@mm.unknown

Living third dispersal stage juveniles of pinewood nematode, Bursaphelenchus xylophilus, were found infesting pine boards in Finland. The boards had been used as building material in a packing case to hold imported machinery. Total numbers of nematodes extracted from the boards did not exceed 4 grams of dry wood. When cultured on Botrytis cinerea the nematode reproduction resumed rapidly.

The PDF includes an abstract in Finnish.

• Tomminen, E-mail: jt@mm.unknown

Different methods of sowing and planting of Norway spruce (Picea abies (L.) H. Karst.) were compared on fertile sites in North Karelia (62°20’N, 29°35’E, 85–120 m a.s.l.). The planting material were 4-year-old bare-rooted transplants, 2-year-old bare-rooted seedlings, and 2-year-old containerized seedlings raised in plastic greenhouse. The sowing methods were band sowing and shelter sowing. Ground vegetation was controlled during the first growing season mechanically or chemically, or the control was omitted totally.

Planting of spruce gave better results than sowing. After eight growing seasons there were sowed seedlings left in 30% of the sowing pots. The average height of them was 35 cm. Seedling survival was best with large bare-rooted transplants (91%). Survival of containerized seedlings was 79% and of small bare-rooted transplants 71%. The average height of large bare-rooted transplants was 131 cm, of containerized seedlings 86 cm and small bare-rooted seedlings 68 cm.

Sowing is not an advisable method for regeneration of spruce due to the small survival rate and slow initial development when ground vegetation is controlled only once. Also 2-year-old seedlings gave a satisfactory result in regeneration. Seedlings raised in greenhouse were more sensitive to frost damage than seedlings grown on open ground.

The PDF includes an abstract in English.

• Kolström, E-mail: tk@mm.unknown

The matrix potential, measured with tensiometers, and its effect on the soil air-water ratio were examined during the production of bare-rooted Scots pine (Pinus sylvestris L.) seedlings in nursery fields. Soil water potential was monitored during the growing season of 1983 at three nurseries in Finland, and from fields growing various seedling types at depths of 10 and 20 cm. In 1986, soil core samples were collected in order to assess the water desorption characteristics of the soil. In addition, the effect of polypropylene gauze covering (Agryl P 17) on the soil water potential was examined during the growing season of 1985 at two nurseries in Finland at depths of 5, 10 and 15 cm.

The soil water potential was relatively high in all the fields studied. In fields growing one- and two-year-old seedlings, the median potential was higher than -10 kPa. The potential did not fall below the limit of the measured scale (ca. -85 kPa) of the tensiometers. Soil aeriation may have been periodically insufficient in the rooting zone, as a result of high water content. The favourable water potential is below -5 to – 6 kPa. The gauze covering slightly (1–4 kPa) increased the soil water potential, an effect which could be harmful if the soil air space is low. During the second growing season, the soil water potential was lower in the fields covered by the gauze during the first year than in the fields without the covering.

The PDF includes an abstract in English.

• Heiskanen, E-mail: jh@mm.unknown
• Raitio, E-mail: hr@mm.unknown

This article is a book review on a book ‘The problems of Forest-based Development as Illustrated by the Development Discussion’ by Jussi Raumolin, concentrating on the development of forestry.

• Leikola, E-mail: ml@mm.unknown

Shoot elongation of Pinus kesiya Royle ex Gordon was studied using 2-year old grafts in a clonal seed orchard of the Pine Improvement Centre, located at the Huey Bong Experimental Station near Chiangmai, Thailand (19° 17’ N, 99° 15’ E, 900 m a.s.l.).

The seed orchard had a completely randomized block design with 30 blocks and 80 single-tree plots (clones) in each block. Eleven clones in four blocks were selected out of the total of 80 grafts (clones). From each graft, three lateral branches at the height of 1.6 m from the ground level were selected. Thus, total of 109 branches were measured. Shoot length of branches was measured between July 3, 1983 and March 11, 1984 at approximately bi-weekly intervals. Method of classical growth analysis were used in describing the shoot growth.

The annual shoot growth pattern of P. kesiya exhibited two consecutive sigmoid growth curves, i.e. it consisted of two flushes of shoot elongation, both formed by free growth. Thus, the pattern of shoot growth resembled the caribaea pattern. However, the annual shoot was composed of summer and winter shoots. These could be distinguished from each other by the reproductive organs, which always occur on winter shoot. The shoot contributed 61% of the total annual shoot length.

There were significant differences in the pattern of shoot elongation between the studied clones, which may reflect differences in the adaptation to different environmental conditions.

The PDF includes an abstract in Finnish.

• Sirikul, E-mail: ws@mm.unknown
• Kanninen, E-mail: mk@mm.unknown

Five ploughed research areas from Finnish Norther Karelia were selected for comparison studies of plough ridges and untouched soil. Measurements were made at a depth of 10 cm in sample plots on both mineral and paludified mineral soil and peatland parts of these areas. In summer 1987 daily soil water matric potential was measured using tensiometers, and volumetric soil moisture content and density were determined from soil samples at two dates during the summer. Water characteristics of the core samples were also determined. On paludified mineral and peat soils the water table depth from the soil surface was measured.

The results indicated that in plough ridges matric potential was lowest. Plough ridges were also seen to dry and wet faster and to a greater degree than untouched soils. In untouched soils, soil water relations and aeration were not affected by the distance to the furrow. The effect of the plough ridge was smallest on peatland, where there was a good capillary connection from plough ridge to the ground water, if the ditches were not very effective. The soil in the ridges did not dry too much to restrict seedling growth. The untouched surface soil in poorly drained peat and paludified minear soil was, at least in a rainy growing season, often and also for long times so wet that 10% minimum air space required for good seedling root growth was not available.

The PDF includes an abstract in English.

• Mannerkoski, E-mail: hm@mm.unknown
• Möttönen, E-mail: vm@mm.unknown

The writer reports in this discussion article of four stands in Finland that have died due to a bolt of lightning. A death of a group of trees because of lightning has been relatively uncommon for the forest professionals. The trees may not have no lightning marks. The four sites are presented in detail. Characteristic for this type of death of trees is, for instance, that trees have died within a circular area (of usually 30 m of diameter), only conifers have died, trees die from the top down, sometimes marks can be found in trees in the centre of the area, and under the bark may be brown patches or stripes.

• Nuorteva, E-mail: mn@mm.unknown

The paper is a review on utilization of peatlands in forestry in the countries of boreal zone: Finland, Norway, Sweden, Canada, the United States and the Soviet Union. First, the concept of peatlands, the types of peatlands throughout the zone are defined, and the use of natural peatlands is described. Finally, the drainage of peatlands for forestry purposes in the countries is reviewed. According to the statistics, a total of 13 million ha of peatlands have been drained in Fennoscandia and the Soviet Union.

• Päivänen, E-mail: jp@mm.unknown

Decision making in the forest protection involves diagnosing the pest, making predictions of the effects of the pest on forest, knowing the possible control tactics, and cost/benefit integration. To cope with all that, a generalist forest manager needs a tool like an expert system to support decisions.

This paper presents an expert system that approaches the goals of integrated pest management. With the systm, the user can make diagnosis and predictions of 12 North European bark beetles. Written in Common LISP and Flavors, the expert system has a combined frame- and rule-based knowledge representation. Frames are used to represent the hierarchy of insect taxonomy in diagnosis. Prediction is made with qualitative reasoning with rules. The interface engine applies both forward and backward chaining. The system has a graphical user interface that supports exploring the sensitivity of advice on input.

It is concluded that expert systems and artificial intelligence have high applicability everywhere in forestry where complicated decisions have to be made. Especially, an integrated pest management system in forestry is largely equivalent to a computerized decision-making aid.

The PDF includes an abstract in Finnish.

• Saarenmaa, E-mail: hs@mm.unknown

When Finland attained independence in 1917–1918, about 65% of her population made their linving from agriculture and only 17% from industry. Despite the fact that most sectors of the modern forest industry, i.e. sawmilling, pulp and paper making as well as plywood industry were then in existence a considerable proportion of timber was exported as roundwood.

It was reasonable to assume, however, that further economic development would reduce the roundwood exports to provide raw material for industry. The present paper investigates the Finnish roundwood exports in 1921–1986 largely from the point of view of this hypothesis. Examination of statistics is focused on the change of volume of exports in the major categories of wood, changes in the trade policies of consumer countries, changes in competition between exporting countries and changes in Finnish export policy.

The PDF includes an abstract in English.

• Holopainen, E-mail: vh@mm.unknown

The paper presents a simple model of long-term forest management planning in tree plantations. The model is particularly suitable for developing countries where the research resources are limited. The management plan is prepared in two steps. First, one or several treatment schedules are simulated for each calculation unit (age class, compartment, etc.) over the selected planning period. Second, an optimal combination treatment schedules according to the selected objectives and constraints is searched by mathematical programming. The simulation of growth is based on the prediction of the diameter distribution at the desired time point. All stand characteristics are derived from this distribution. The models needed in the yield simulation can be estimated from temporary sample plots. A case study management plan for 13,000 ha of Pinus kesiya (Royle ex Gordon) plantations in Zambia is presented to demonstrate the system.

The PDF includes an abstract in Finnish.

• Pukkala, E-mail: tp@mm.unknown
• Mubita, E-mail: om@mm.unknown
• Saramäki, E-mail: js@mm.unknown

In soil profiles from a series of uplands of different site types bulk density, density of solids and porosity of soil were clearly related to soil organic matter content and its distribution in the soil profile. Soil organic matter contents were also strongly correlated to effective cation exchange capacity (CEC) and soil acidity. Site fertility was primarily related to the fine fraction (ø<0.06 mm) content in the C horizon and related properties (i.e. CEC). In the humus layer, the content of exchangeable bases and base saturation most strongly related to site fertility.

The PDF includes an abstract in English.

• Westman, E-mail: cw@mm.unknown

A close relationship between photosynthetic capacity and nitrogen concentration of leaves is known to exist. In conifers, nitrogen also affects the pattern of mutual shading within a shoot, which is a basic unit used in studying photosynthesis of coniferous trees. These effects of needle nitrogen concentration on photosynthetic capacity and mutual shading of needles were analysed for Scots pine (Pinus sylvestris L.) shoots taken from five young stands growing on sites of different fertility. The effect of nitrogen concentration on needle photosynthesis was studied based on measurements of the photosynthetic radiation response of shoots from which two thirds of the needles were removed in order to eliminate the effect of within shading.

An increase of one percentage unit in nitrogen concentration of needles increased the photosynthetic capacity of needles by 25 mg CO₂ dm^-2h^-1. The effect of nitrogen on within-shoot shading was quantified in terms of the silhouette area to total needle area ratio of a shoot (STAR), which determines the relative interception rate per unit of needle area on the shoot. Although nitrogen promoted needle growth, an increase in nitrogen concentration decreased the within-shoot shading. This effect resulted from a decrease in needle density on the shoot and an increased needle angle with increasing nitrogen content.

The PDF includes an abstract in Finnish.

• Smolander, E-mail: hs@mm.unknown
• Kellomäki, E-mail: sk@mm.unknown
• Oker-Blom, E-mail: po@mm.unknown

The results of regenerating 54 and 36–38-year old strip cuttings were surveyed in the Kivalo Research Forest (N 66°20’, E 26°40’). 15 measurement plots were placed on each strip. The most common forest type was Hylocomnium-Myrtillus type. Regeneration of the strips proved to be slow. Most of the spruces growing on the strips probably originated from the time before the cutting. The average number of stems was 1,155 per ha, of which one third consisted of broadleaved trees. The average volume increment of stem wood after cutting had been about 1 m³/ha/yr, but it was increasing at the time of the inventory. Both the reforestation of the strips and the development of the emergent stands were dependent on elevation and site fertility. Site fertility was indicated by the abundance of Vaccinium myrtillus.

The PDF includes an abstract in English.

• Pohtila, E-mail: ep@mm.unknown

Containerized tree seedlings will be used on an increasing scale in the future in different parts of the world. There are number of techniques for the production of small one-year-old seedlings but it has not been possible to develop a completely satisfactory methods for large containerized seedlings production. In the long-term development of pine plantations established with containerized seedlings the greatest problem has been deformation of the root system. With a new method, based on a sheet of peat and root pruning, it has been possible to produce conifer seedlings with a good root regeneration potential and favourable morphological root system development. The use of small containerized seedlings allows an increase in planting density without any marked increase in regeneration costs.

The PDF includes an abstract in English.

• Parviainen, E-mail: jp@mm.unknown

Refertilization with PK, about 15 years after the first fertilizer application, increased tree growth and the amount of nutrients in tree litter in Scots pine (Pinus sylvestris L.) and birch (mainly Betula pubescens Erhr.) stands on a drained fertile mire in Northern Finland (65°34 N’, 25°42’ E). The increase in growth and nutrient contents after refertilization was greatest in the mature pine stand where the application of nitrogen and micronutrients gave an additional response compared to the PK-application.

The PDF includes an abstract in Finnish.

• Paavilainen, E-mail: ep@mm.unknown

Seed mass within any plant species is one of the least plastic components of plant structure. The aim of this study was to analyse the variation in the seed mass of Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) H. Karst.) in relation to three environmental factors: soil fertility, mean temperature and precipitation during seed filling period. Data published earlier on seed mass of these species on different sites and different years was used in the study.

The seed mass of both species was independent of soil fertility (forest type) but did vary between different years. It is hypothesized that if the seed-ripening summer is warmer than average, Scots pine seed mass tends to be smaller. In this study, seed mass varied independently of the amount of precipitation during the ripening summer. However, generalization of the results requires further study.

The PDF includes an abstract in English.

• Nygren, E-mail: mn@mm.unknown

The structure and functional responses of roots in planted seedlings when acclimatizing at the planting site are reviewed. A wide range of methods for classifying roots has been employed, and the terminology used is not uniform. Roots can be classified by their morphology, origin, and function. The temporal and spatial variation of soil temperature, moisture, structure, and concentration of nutrients are among the most important properties to which root systems acclimatize. In order to reliably describe the function of the root system, several parameters usually have to be measured. Studies on the root-soil interface have indicated that roots are not necessarily in continuous contact with soil. The control mechanism of root growth is inadequately known and theoretically formulated. Generally, only the mass needed for water and nutrient uptake has been allocated to the roots. However, the amount of photosynthates allocated to the roots is high. Acclimatization of seedlings out at the planting site is a complicated process which is influenced by the growing conditions at both the nursery and at the site. The function, distribution and structure of roots are controlled by the environment in a way similar to the shoot, but the control mechanism is imperfectly known.

The PDF includes an abstract in English.

• Lippu, E-mail: jl@mm.unknown
• Puttonen, E-mail: pp@mm.unknown

While the most common type of mycorrhizae is endomycorrhizae, ectomycorrhizae dominate in the case of coniferous trees. Pine, in particular, has a strong association with mycorrhizae. Mycorrhizae enable trees to take up water and nutrients much more efficiently than the roots themselves. The fungus, in return, obtain carbohydrates and is able to grow and fruit. Mycorrhizal fungi are probably numbered in their thousands but so far few are known. Knowledge about their physiology, in particular, is lacking and studies dealing with their isolation and inoculation, which may be commercially valuable, remain unpublished. A new challenge for mycorrhiza research is the effects of air pollution. Forest suffering from extensive air pollution have few mycorrhizal fungi., infection is weak and the number of root deformations is high. As good mycorrhizae are important to tree health, there is a particular need to intensify mycorrhiza research.

The PDF includes an abstract in English.

• Laiho, E-mail: ol@mm.unknown

The winter 1986–87 was unusually cold; the snow cover remained thin and consequently the soil froze to a considerable depth. In spite of the severe frost, the lowest temperatures measured at the ground surface was -10.3°C and in the soil at the depth of 10 cm -5.8°C. The temperature sum of the following summer was unusually small and the soil frost melted more slowly than usual. The winter frosts did not have a decisive influence on the survival of planted seedlings.

The PDF includes an abstract in English.

• Kubin, E-mail: ek@mm.unknown

The author first introduced the cut-block seedling production method to Finland in 1969. The aim is to raise seedlings whose lateral roots do not become deformed as a result of a restricting container or other external pressure. The seedlings are raised in a large, fairly compact substrate block where the roots can freely develop in a normal fashion. The blocks are then cut up into individual cubes, each containing a seedling. The precise positioning of the sowing point permits mechanization of the work.

The PDF includes an abstract in English.

• Huuri, E-mail: oh@mm.unknown

Based on literature this paper describes the natural afforestation of Finland that took place after the last ice age and the changes which have taken place during the last 10,000 years. The origin and development of the vegetation and trees are related to the changes in the edaphic and climatic factors. The first tree species to arrive in Finland were the primary colonizing species, birch and Scots pine. The appearance of Norway spruce dates back to about 5000 B.P. There have been great changes in the species composition of Finnish forests during the last several thousands of years but some 2,000–3,000 years ago the various species reached their present balance. The epoch of naural forests, which had lasted some 9,500 years, came to a conclusion, however, when man started to have a marked effect on the forest’s development 300–400 years ago.

The PDF includes an abstract in English.

• Alho, E-mail: pa@mm.unknown

On 23th of March 1989 professor emeritus Paavo Yli-Vakkuri celebrated his 75th birthday. In 1963–1977 he acted as professor of silviculture and Head of the Department of Silviculture at the University of Helsinki. Due to his personality and positive attitude towards students and younger colleqaues, silviculture became the most popular subject for the graduate and postgraduate forestry students, and active research flourished at the Department of Silviculture during his era. This issue of Silva Fennica is dedicated to Paavo Yli-Vakkuri in gratitude and respect for his professional accomplishments in academic studies and research in forest sciences.

The PDF includes an abstract in English.

• Leikola, E-mail: –
• Koponen, E-mail: –

This paper is a commentary which summarises the history of the Finnish Society of Forest Science and its connection to the corresponding society in the field of agriculture, the Scientific Agricultural Society of Finland. The original idea when the Scientific Agricultural Society of Finland was founded was that the society would function as a scientific society for both forest scientists and agronomists. However, A.K. Cajander founded a separate academy for forest sciences. The article discusses the implications of this decision. 

• Leikola, E-mail: ml@mm.unknown

The element content (Ca, Mg, K, Na, Fe, Mn, Zn, Cu, Pb, S) of Scots pine (Pinus sylvestris L.) bark and Bryoria lichens, as well as the occurrence and coverage of epiphytic lichens and the length of Bryoria species, were studied in the vicinity of Kolari cement works, NW Finland. Fruticose Bryoria species had the highest coverage on pine trunks at a distance of 2 km or more from the cement works. At a distance of 1 km the foliose – or even crustose – Parmeliopsis species were most abundant, while nearer to the works lichens were almost completely absent. The length of Bryoria was reduced at distances of less than 2 km from the cement works. The calcium content in Bryoria species increased very steeply close to the works; by a factor of 60 at a distance of 1 km compared to 16 km. No corresponding increase in other elements was observed near the cement works. All the elements studied in pine bark showed a significant negative correlation with distance, and a significant positive correlation with the calculated dust deposition levels. There were only minor differences between the north and south of the pine trunks, or the side facing or away from the works. Pine bark analysis is recommended for element accumulation studies.

The PDF includes an abstract in English.

• Kortesharju, E-mail: mk@mm.unknown
• Kortesharju, E-mail: jk@mm.unknown

This paper is a review on the development of sustainable forest management and what has been meant with the term in different times. The article summarises the birth of sustainable use of forests in the world and in Finland, and discusses sustainability in forest management, for instance from the point of view of one forest holding, large clearcuttings performed in Lapland, biological sustainability, business economics and overall planning.

• Kilkki, E-mail: pk@mm.unknown

The paper continues an earlier study by Kilkki and Päivinen concerning the use of the Weibull function in modelling the diameter distribution. The data consists of spruces (Picea abies (L.) H. Karst.) measured on angle count sample points of the National Forest Inventory of Finland. First, maximum likelihood estimation method was used to derive the Weibull parameters. Then, regression models to predict the values of these parameters with stand characteristics were calculated. Several methods to describe the Weibull function by a tree sample were tested. It is more efficient to sample the trees at equal frequency intervals than at equal diameter intervals. It also pays to take separate samples for pulpwood and saw timber.

The PDF includes an abstract in Finnish.

• Kilkki, E-mail: pk@mm.unknown
• Maltamo, E-mail: mm@mm.unknown
• Mykkänen, E-mail: rm@mm.unknown
• Päivinen, E-mail: rp@mm.unknown

The shape of Scots pine (Pinus sylvestris L.) knots close to the pith of butt logs was investigated. 1,100 knots were split in a vertical direction, and their shape was measured. Knot diameter and branch angle were calculated at a distance of 40 mm from the pith of the stem. The mean diameter of all the knots in the material was 14 mm, and the branch angle 70°. Regression analysis was used to devise a formula for predicting branch angle on the basis of knot diameter. Knot size and branch angle were negatively correlated. Especially the shape of larger knots was curved. Knots achieved their maximum diameter at distance of 4–5 cm from the stem pith. The branch wood was almost completely situated above the formation point of the branch.

The PDF includes an abstract in Finnish.

• Pietilä, E-mail: jp@mm.unknown

Ring width at breast height is presented as a function of stem radius at breast height, the ratio between the diameter of a tree and the basal area median diameter, site index, and density of stand. By means of a conversion model ring width at stump height can be estimated as a function of ring width at breast height.

According to previous studies substantially better wood quality can be expected if mean width near the pith at stump height decreases from 3 to 2 mm. According to the present study only on the poorest sites suitable for Scots pine (Pinus sylvestris L.) planting (poor Vaccinium type) the ring width is less than 3 mm at stump height even in the thickest trees. On more fertile sites a substantial increase in the recommended planting density is required, if the mean ring width is aimed to be less than 3 mm. On the best sites it is impossible to reach mean ring width of less than 2 mm, when the density is less than 4,000 stems/ha. Only the thinnest trees on the poorest sites can have a mean ring width less than 2mm.

The PDF includes an abstract in English.

• Varmola, E-mail: mv@mm.unknown

According to 459 and 350 questionnaires sent in 1983 and in 1985, respectively, the households in the Rovaniemi region located in the Arctic Circle in Northern Finland, eagerly picked wild berries. In both years, four out of five households picked at least one species of berry. In 1983 the total amount of wild berries picked was 29.2 kg per capita. In 1985 it was 15.0 kg per capita. Three species, the lingonberry (Vaccinium vitis-idaea L.), cloudberry (Rubus chamaemorus L.) and bilberry (Vaccinium myrtillus L.) made up 96% of all the wild berries picked during both years. Most of these berries were picked for the family’s own use, but many were also picked for sale. In 1983, 43% of all berries picked were sold, in 1985, 19% were sold. The cloudberry, although difficult to find, is the most important commercial species and also for household use it is the most sought after wild berry. Only very small amounts of edible mushrooms were collected, 1.0 kg per capita in 1983 and 1.3 kg in 1985.

The PDF includes an abstract in Finnish.

• Saastamoinen, E-mail: os@mm.unknown
• Lohiniva, E-mail: sl@mm.unknown

The experiment was performed in 1982–85 at the forest tree nursery in Suonenjoki, Central Finland. There were four to five transplanting dates ranging from the beginning of August to the end of September. The dry matter content, root regeneration and needle retention value of Scots pine (Pinus sylvestris L.) seedlings were examined. Development of the needle retention value in autumn was followed in nurseries at Suonenjoki, Rantasalmi, Mäntyharju and Taavetti in 1982.

Root regeneration was usually the worse, the later the seedlings were transplanted in the autumn. The dry matter content was generally lowest in the seedlings transplanted later in the autumn, and also to some extent in the seedlings transplanted at the beginning of August. The needle retention value increased as autumn advanced. Early transplanting in autumn had an adverse effect on the development of needle retention, and the values were highest in the seedlings transplanted later in the autumn.

The PDF includes an abstract English.

• Petäistö, E-mail: rp@mm.unknown

Frankia was isolated from the root nodules of Casuarina equisetifolia L. seedlings, grown in a growth chamber, after inoculation with soil originating from an old east Kenyan casuarina forest. Optimum pH for the growth of the two isolates ranged from 6.4 to 6.9. The optimum temperature for their growth was 32°C. The growth of these cultures ceased at NaCl concentration above 2%. The influence of the isolates on the growth of the host plant was determined in a growth chamber experiment in which an American Frankia strain (HFPCc13) was used as a reference. The biomass of the inoculated seedlings was 2.4–4.1 fold those of the non-inoculated control seedlings at the end of the 7-month experiment.

The PDF includes an abstract in Finnish.

• Miettinen, E-mail: pm@mm.unknown
• Smolander, E-mail: as@mm.unknown

In this article the methods of forest valuation, especially the sales value tables previously published in Finland are critically examined. In this connection attention is drawn to the rate of interest used in calculating the forest values.

The PDF includes an abstract in English.

• Hämäläinen, E-mail: jh@mm.unknown

The condition of forest road pavements was studied in spring, one week after maintenance and in autumn. The effect of vibrating blade was slightly better than that of pulled drag. Large loose stones couldn’t be pressed into pavement with either of the implements. The use of the vibrating blade was three times as expensive as the use of the pulled drag, however, the blade is suitable for other purposes as well.

The PDF includes an abstract in Finnish.

• Rummukainen, E-mail: ar@mm.unknown

The material of the study consisted of 21 Scots pine (Pinus sylvestris L.) trees that had been pruned in the 1930’s and 1940’s. The butt log of the pruned stems was peeled into veneer from which the length and shape of the resin taps were determined. The length of the resin tap was affected in the first place by the knot diameter and the height of the knot along the stem. The length of the resin tap was about 1.5-fold that of the knot diameter. With an increase in the height above the ground of a knot, its length decreases. The resin taps were particularly long on poor sites and in the butt end of the stems, however, the variation in tap length was large both within and between the individual tree stands. The shape of the resin taps is presented in this study by diameter classes. The resin taps studied in the work were longer than those measured in other works. This may be due to the fact that the knots were uncovered by peeling instead of sawing.

The PDF includes an abstract in Finnish.

• Pietilä, E-mail: jp@mm.unknown

The results of an intercalibration of sulphur analysis by 24 laboratories are evaluated. The analysis was made by one or more of six methods. The following three methods were found to be satisfactory as regards relative speed and reliability: Leco S analysis, X-ray fluorescence, and vacuum ICO emission spectroscopy.

The PDF includes an abstract in English.

• Jarva, E-mail: mj@mm.unknown
• Tervahauta, E-mail: at@mm.unknown

Properties of fibres in pulpwood, especially length, width and the thickness of walls in tracheids, are essential for strength properties of pulp and paper. Length and width of tracheids increase from pith to surface in radial direction. Young and small-sized stems have also smaller fibres. Small-sized Pinus sylvestris L. test trees had tracheids that were shorter both in stems and knot wood than those in normal sized trees. However, cell walls in test trees were as thick as in normal sized trees. It seems that especially the L/T -ratio (length/thickness) in small stems is worse than in normal sized pulp wood.

The PDF includes an abstract in English.

• Laurila, E-mail: rl@mm.unknown

The area of stands studied by line plot survey was 594 ha. On the basis of the length of the inventory line the estimated proportion of harvesting strips was 14% and that of ditch openings 6% of the area. The calculated strip road spacing was 29 m. The option of the minimum diameter made it difficult to use the number of stems as criterion for thinning intensity. Thinning intensity evaluated according to the basal area had been stronger than recommended with low values of dominant height and milder with high values. The estimated removal according to stumps was 38 m³/ha on the average between the strips. The real removal has, however, been larger than that, as the strip road openings are made in connection with the first thinning.

The PDF includes an abstract in English.

• Rantonen, E-mail: hr@mm.unknown
• Päivänen, E-mail: jp@mm.unknown

The two introductory books written by emeritus professor William Duerr provide an opportunity to scope the research progress in the forest economic discipline during almost a quarter century. This paper gives a presentation of the books (Fundamentals of Forest economics, 1960, and Forestry Economics as Problem Solving, 1984), and the development of forest economics during the period.

The PDF includes a summary in English.

• Ollonqvist, E-mail: po@mm.unknown

The Academy of Finland commissioned a review of forest regeneration research. This paper summarises the evaluation. The report deals with the individual research projects and, in addition, the international evaluation group gives several recommendations to develop the forest regeneration research further. The recommendations concern education and training, publications, peer review, experimental design, routine work and extension service, and technology transfer. The paper also includes comments of the Finnish Forest Institute, the Finnish Society of Forest Science and a research scientist on the results of the evaluation.

The PDF includes a summary in English.

• Puttonen, E-mail: –

The effect of root exposure on the shoot and root development of Pinus sylvestris (L.) seedlings was studied at two soil temperatures. Roots of bare-rooted three-year-old seedlings were exposed to the temperature of 32°C at relative humidity of 50–40% for 85, 155 and 270 minutes which corresponds to accumulated water pressure deficit of 24, 47 and 91 mbar·h, respectively. Thereafter, seedlings were grown for 65 days at the soil temperatures of 12 and 23°C. Drought exposures inhibited new root initiation, delayed shoot elongation, and reduced shoot and needle growth. The stronger the exposure the larger the proportion of needles from the lower part of current shoot that remained undeveloped. Low soil temperature increased the effect of exposures so that needle elongation and initiation of new root tips of seedlings in cold soil with the longest exposure were inhibited totally. Root growth assessments made in warm soil may overestimate the acclimation potential of planted seedlings.

The PDF includes an abstract in English.

• Rikala, E-mail: rr@mm.unknown
• Puttonen, E-mail: pp@mm.unknown

Frost resistance during shoot elongation in seedlings of Norway spruce (Picea abies (L.) H. Karst.) was studied in two experiments. The aim of the first study was to evaluate the effect of varying mineral nutrition. Except for potassium, only minor differences in mineral elements concentrations were established, presumably due to low levels of irradiance and thus a low rate of dry matter production. No significant differences in frost injuries were found between the treatments in the experimental series, but the control seedlings were significantly less injured. It is assumed that poor hardiness development at the end of one growth period resulting from low levels of irradiance may decrease the frost resistance during the next shoot elongation phase. Observations from the second experiment with Norway spruce nursery stocks representing different seedling ages and production systems, support this assumption.

The PDF includes an abstract in Finnish.

• Rostad, E-mail: hr@mm.unknown

The effect of drainage on structure of tree stands is analysed by comparing the average structural characteristics (e.g. diameter distribution) of stands in the data for different drainage age classes and selected site types. The material consists of ca. 4,400 relascope sample plots, which are part of a large drainage area inventory project. The uneven-aged structure of the virgin peatland forest is preserved for several decades after drainage. This is enhanced by the post-drainage increase of small-diameter trees, especially birch. The number of trees per hectare increased during a period of ca. 30 years and levelled off thereafter. The increase in the number of saw log stems is clearly related to the fertility of the site and its geographical location.

The PDF includes a summary in English.

• Hökkä, E-mail: hh@mm.unknown
• Laine, E-mail: jl@mm.unknown

The fungal symbiont of ectendomycorrhizae is an ascomycete Wilcoxina (Tricharina) mikolae Yang & Korf. It forms ectendomycorrhizae with Pinus and Larix and ectomycorrhizae with Abies, Picea, Pseudotsuga and Tsuga. It is common in forest nurseries around the world. After transplanting the seedlings into natural forest soil, indegenous fungi rapidly replace Wilcoxina. Inoculation of nursery soil with Wilcoxina is recommended if soil has been sterilized or for other reasons mycorrhizal fungi are absent.

The PDF includes a summary in Finnish.

• Mikola, E-mail: pm@mm.unknown

In Finnish music national forests and international urban culture meet in an original way. Around the last turn of century, composers believe they had discovered their spiritual roots in nature and especially in the forests. The universal musical language of Jean Sibelius, for example, is based on a deep Finnish identity, the atmosphere of Kalevala. Sibelius’ Tapiola is, thus, among our century’s most powerful musical interpretations of feelings about nature. Nature inspired music is, generally, associated with such positive qualities as beauty, peace, softness, light and joy. A great deal of forest music is based on literature, where natural images have almost always had a positive interpretation.
The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Hako, E-mail: ph@mm.unknown

Several views to forest’s role in the Finnish folklore are presented. They clearly show how many important dimensions forests have had in Finnish life. Descriptions concentrate on forest-related traditions of ancient times. They give a basis to examining the role of forests in the modern Finnish mind.

The paper is based on a lecture given in the seminar 'The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Virtanen, E-mail: pv@mm.unknown

The paper presents aspects of town and forest architecture. A feature of the Finnish building tradition is that the forest is allowed to grow next to buildings. After the Second World War a new type of town was created in Finland, ”the forest town”. The most prominent feature of the history of Finnish architecture, from national romanticism to functionalism and up to the present day, is the modification of international ideals to a certain ”forest culture” style.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Pallasmaa, E-mail: jp@mm.unknown

The Finnish forest was elevated into an appreciated artistic motif by Werner Holmberg with his picture ”The Finnish conifer forest” in 1858. The second significant period was during national romanticism in the 1980’s, when the decorative beauty of the winter forests was discovered. At the turn of the century, the forest obtained a central national symbolic significance, and many leading artists regarded increased cuttings as a rape of the forests. Since that period, individual artists have succeeded in bringing new features in the art history of our forests.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Reitala, E-mail: ar@mm.unknown

In world literature, there are many forests of significance, e.g. oak forest of Mamre and in Dante’s Divine Comedy. Finnish literature has abounded with forest topics since ancient folkore. We have a literature of floaters, loggers and paper workers of industrialized Finland, not to speak of a hunting literature. A major theme is ”from forest to town”, where the first work, Aleksis Kivi’s ”Seven brothers”, is a landmark in Finnish literature. Forests of many other authors are also presented, as well as ancient chants and poems.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Suhonen, E-mail: ps@mm.unknown

According to universal primitive beliefs, there was a huge pole or tree in the centre of the universe to support the sky. These beliefs gave rise to innumerable customs where both trees and wood have been used to promote health and good luck. Even today, many such customs exist: the Christmas tree, maypole, Midsummer birches, birch whisks in the Finnish sauna, ritual tree plantings etc. In addition to the tree, also the forest as both a protecting and a frightening maternal symbol can be considered as an archetype. Intensive forestry diminishes the archetypal contents of forests, which may be one reason behind critical attitudes towards modern forestry.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Reunala, E-mail: ar@mm.unknown

The security provided by forests is approached through various authors’ descriptions and through psychotherapeutic experience. The lap of the forest can recreate early security, protection and unity, for example the lap of mother or father. The forest is also a safe place to externalize inner feelings, desires, fears and erotic images. Intensive forest management and air pollution are nowadays threatening the protective role of forests.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Siltala, E-mail: ps@mm.unknown

Sociological studies on the way of life tell rather little about the impact of forests on Finn’s everyday life. The change of life styles, urbanization and middle-class values, signify a detachment from immediate and practical relationship with nature. Those born in the countryside conserve their relationship with nature in their leisure activities, but the urban-born generation needs the mass-media, education, travel and other institutions in order to maintain and develop its relationship with nature.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Ahponen, E-mail: pa@mm.unknown

The earliest manor parks, which are a special form of cultivated forests, were created at the end of the 18th century. The surrounding of the main buildings was divided into two parts, an aesthetic park and yard serving household and economic purposes. Early in the 19th century, large parks were created which represented dominant aesthetic ideals but, on the other hand, formed a ”wild” counterpart to the structured inner world of the main building. A good example is Ratula Manor and its park, which represent the diversity of the cultivated forest of the 19th century manors.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Lönnqvist, E-mail: bl@mm.unknown

The paper describes some examples from Paris and Helsinki areas, where trees are essential landscape elements. It is typical in France to plant trees around town squares, market places and along streets and roads. In Finland trees are almost always kept close to the house, together with other vegetation protecting the entrance and windows. These traditional uses of trees should be studied to serve landscape management.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in Finnish.

• Guignard, E-mail: mg@mm.unknown

Forstästhetik is a programme for forest management, resembling an art manifesto. Forest managers are programme executors. Forest aesthetics is forest investigation from the point of view of beauty. In the case of managed forests, it is possible to ask, what is the manager’s programme and his skill to achieve personal solutions. In forests, the functioning and sustainability of the ecosystem are basic principles affecting all other values. On this basis it is possible to evaluate the competence of taste systems and the logic of their application.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Sepänmaa, E-mail: ys@mm.unknown

The main features of the Finnish landscape are a result of preglacial erosion processes and the structural lines of the bedrock. The microstructure of the landscape was created by the Ice Age and its melting processes. Upon this base, human activities have created a palimpsest of cultural landscapes. The article describes the effects of slash-and-burn cultivation, tar production, cattle ranging and some other forest uses to the forest landscape. 

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Linkola, E-mail: ml@mm.unknown

The article compares forest images in provincial and patriotic songs and in forest advertisements by banks and insurance companies. In songs, coniferous forests represent the primaeval nature and broadleaved forests represent culture. Coniferous forest is the real patriotic forest. Forest images in advertisements are twofold: both elevated patriotic forests and profane raw-material forests are found.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Julkunen, E-mail: ej@mm.unknown
• Kuusamo, E-mail: ak@mm.unknown

Only a few studies exist concerning the political anthropology and geopolitics of forests. The role of forests in European geopolitics and their role in restraining concentration of power and promoting guerrilla warfare is examined. The shelter of forest cover has been a fundamental factor for the formation of the Finnish people and it has also played an important role in the defence of independent Finland. Clearcuttings, forest roads and modern reconnaissance technology have recently diminished the protective shelter of forests.

The paper is based on a lecture given in the seminar ‘The forest as a Finnish cultural entity’, held in Helsinki in 1986. The PDF includes a summary in English.

• Raumolin, E-mail: jr@mm.unknown

• Leikola, E-mail: ml@mm.unknown

This publication consists of 16 papers on importance of forests to Finns, mainly from the viewpoint of various social and humanistic sciences. The articles are based on lectures given to a seminar organized in Helsinki, December 18-19, 1986.

This paper includes preface and list of the speeches in English.

• Reunala, E-mail: –
• Virtanen, E-mail: –

Logical structure of three simulation models and one conceptual model concerning effects of temperature on dormancy release in woody plants was examined. The three basic types of simulation models differed in their underlying assumptions. Contrasting implications of the models were inferred by deduction. With the aid of these implications, the model types can be tested using experiments with continuous and interrupted chilling. Similarly, implications of the conceptual model of rest phases were inferred, by which the model can be tested using experiments with continuous chilling and forcing in multiple temperatures. The possibilities to synthetize the conceptual model with any of the three simulation model types, as well as the biological interpretation of the model variables, were discussed.

The PDF includes an abstract in Finnish.

• Hänninen, E-mail: hh@mm.unknown

Four teams of two workers were time-studied in clearcutting of a cypress plantation and three teams in sulky skidding. The heart rate was recorded every 30 s. The average heartrate in timber cutting was 117.5 ± 13.4 P/min, and it was mainly dependent on worker’s working capacity. Average work load index was 41 ± 3% when working at 97% performance. The production rate was then 2.5 m³/h (crew). In sulky skidding the heart rate was lower, 106 ± 1.1 P/min, as well as the work load (WLI 30 ± 1%) and performance rating (87%). The low production rate (1.1 m³/h) (crew)) over 45 m distance is mainly due to under-dimensioned load size. The energy expenditure in timber cutting was 21.4 kJ/min and in sulky skidding 16.3 kJ/min. Daily energy expenditure was 15.0 MJ/d, and most of the timber cutters belonged to the class ”exceptionally active”.

The PDF includes an abstract in Finnish.

• Saarilahti, E-mail: ms@mm.unknown
• Bakena, E-mail: eb@mm.unknown
• Mboya, E-mail: gm@mm.unknown
• Minja, E-mail: tm@mm.unknown
• Ngerageze, E-mail: tn@mm.unknown
• Ntahompagaze, E-mail: jn@mm.unknown

The study material consisted of 13 rather old Norway spruce (Picea abies (L.) H. Karst.) and 17 Scots pine (Pinus sylvestris L.) stands located in different parts of Finland. In each stand the seed crops, radial growth and amount of latewood were measured during a period of about ten years. Seed production reduces the radial growth of spruce and pine in the year of seed maturing. In Southern and Central Finland also the proportion of latewood is reduced. Seed production accounts for about 14% of the variation in radial growth of a spruce stand growing in Lapland, and 27% in other parts of Finland. In pine stands the seed crop explains 19% of the variation in radial growth in Lapland, and only 7% in the rest of Finland. In spruce stands an average seed crop reduces radial growth by 14% in Lapland and 5% in the rest of the country. An abundant seed production causes a reduction of about 20%. In southern parts of Finland, the proportion of latewood is reduced by 5% in an average seed year and by 24% in a good seed year. In pine stands an average seed crop decreases the width of annual ring by 5%, and a good seed crop by 15%. Outside Lapland, also the proportion of latewood is reduced: in an average seed year by 5%, and in a good seed year by 16%. The reduction in volume growth of spruce stands due to an average seed crop was estimated to be about 10% in Lapland, and 6% in other parts of Finland. A prolific seed production causes a reduction of 20%. In old pine stands the reduction is 5% in an average seed year, and 15% in a good seed year.

The PDF includes an abstract in English.

• Pukkala, E-mail: tp@mm.unknown

The seed crop of Norway spruce (Picea abies (L.) H. Karst.) and Scots pine (Pinus sylvestris L.) is predicted with the help of mean monthly temperatures during May–August one and two years before the flowering year. The prediction models were made separately for Lapland and for the rest of Finland. The models are based on 10-year periods of seed crop measurements and climatic data. The total number of time series was 59.

In Lapland, Norway spruce flowered abundantly and produced an abundant seed crop after warm July–August and two years after cool July–August. In other parts of Finland, warm June and July produced a good flowering year, especially if these months were cool two years before the flowering year.

In Lapland, Scots pine flowered abundantly if the whole previous growing season was warm. Elsewhere in Finland, a cool June preceded prolific flowering in the coming year if the rest of the growing season was considerably warmer than the average.

The prediction models explained 37–49 % of the variation in the size of the seed crop. The occurrence of good and poor seed years was usually predicted correctly. Using the presented models, the prediction of the seed crop is obtainable 1.5 year for Norway spruce and 2.5 year for Scots pine before the year of seed fall.

The PDF includes an abstract in English.

• Pukkala, E-mail: tp@mm.unknown

In laboratory studies the heartwood content seems to be the only natural property of a wood of different tree species influencing the decay resistance. Moistening and drying by diffusion happen quite slowly. Scots pine (Pinus sylvestris L.) sapwood takes moisture by capillary action quicker than pine heartwood and Norway spruce (Picea abies (L.) H. Karst.) wood. Swelling and shrinkage are also greatest in pine sapwood. Impregnation of pine sapwood can give it better hydrophobic and dimensional stability than that of pine heartwood.

The PDF includes an abstract in English.

• Kärenlampi, E-mail: pk@mm.unknown

A team of 2 experienced workers was time-studied and their heart rate recorded under 4 days in clearcutting of a highly self-pruned Pinus patula Schltdl. & Cham. plantation. Task work and bonus payment systems were compared, but there was no difference in production rate, only the workplace time was extended from 2.3 h/d in task work to 3.9 h/d in bonus payment. The heart rate was 115–116 P/min in felling, 105–109 P/min in debranching and 109–114 P/min in bucking. The average heart rate in timber cutting was 108–109 P/min. Work load index was 34–37%, and the workers did not show any symptoms of accumulated stress. The production rate was 3.2 m³/h, (WPT, crew), which corresponds average piecework rate, the comparable walking speed being about 6.0 km/h. There are possibilities to increase the daily task by ergonomic grounds.

The PDF includes an abstract in Finnish.

• Saarilahti, E-mail: ms@mm.unknown
• Ole-Meiludie, E-mail: ro@mm.unknown

This study deals with the evaluation of logging machines. The analyses were based on the results of a productivity study with special reference to a PIKA 35 processor, a delimber-bucker, working in Kyröskoski forest area in Finland. Factors affecting the productivity of the machine were surveyed. Mathematical models for determining the productivity were developed and their practical applications to the particular problem under study was demonstrated.

The PDF includes an abstract in Finnish.

• Tan, E-mail: jt@mm.unknown

This study deals with significance of the number of needle year classes in estimating the nitrogen, phosphorus, potassium and magnesium status of Scots pine (Pinus sylvestris L.) plants on the basis of needle analysis. Due to the nutrient retranslocation deficiencies in these nutrients are best determined by analysing separately the needles of the topmost branch whorls possessing one, two or three needle year classes. The concentrations of those nutrients which are not scarce will then increase as needle year classes decrease. In cases of deficiency, on the other hand, the content of the nutrient concerned will remain the same or decrease. Only severe deficiencies are revealed by the examination of the nutrient concentrations of only the youngest or the oldest needles.

The PDF includes an abstract in English.

• Raitio, E-mail: hr@mm.unknown

In order to understand the present forest policies for the small woodlot of Quebec, it is essential to understand the history of settlement of Quebec. Following this brief description, the author introduces the various forest policies (programs) which have been initiated in Quebec by various levels of governments in order to deal with the management of these lands.

• Gendreau, E-mail: cg@mm.unknown

Standard methods of welfare economics are used in a market simulating framework to evaluate policy measures designed to increase future timber supplies. Forest management cost-share programs are examined using this methodology. The differential regional impact of cost-share payments is considered, as is the distribution of these benefits between stumpage producers (owners of forest land) and stumpage consumers (producers of forest products). Previous estimates of the welfare gains that would result from a higher level of forest management cost-share payments in the southern United States are revised to account for the loss of public revenue resulting from lower future prices. A methodology for comparing alternative policy instruments is discussed, and a preliminary, qualitative comparison is made between the use of cost-share payments and alternative policy measures.

• Brooks, E-mail: db@mm.unknown

The purpose of this paper is to present an approach to evaluate the profitableness of a forest policy program and to discover from among the feasible programs the one that best complies with the desired performance of the economy. At first the procedures of forest policy-making in a country like Finland is considered. After that a method to evaluate forest policy programs is derived.

• Vehkamäki, E-mail: sv@mm.unknown

The basic density of the wood of the rowan tree (Sorbus aucuparia L.) is almost the same along the stem but that of the bark is increasing along the stem. The moisture content of the wood and of the bark is increasing along the stem. Its strength in the bending and in the compression is high. The volume shrinkage is high.

The PDF includes an abstract in Finnish

• Maasalo, E-mail: km@mm.unknown

The purpose of the study was to determine the effects of the origin of seeds and the location of cultivation of Scots pine (Pinus sylvestris L.) on certain properties particularly important to the pulp industry. The research material consisted of six parallel trials of the same 12 provenances. Increment cores were taken of a total of 1,267 sample trees, 19 years old. The location of the trial site generally affected the properties to a larger extent than the origin of the seed. The effect of the variation of wood density and fibre yield on the cultivation values of the provenances was only a few percentages on average, however, at most the effect was nearly 10%. Eastern Finnish provenances adapted well to western Finnish conditions.

The PDF includes an abstract in Finnish and French.

• Velling, E-mail: pv@mm.unknown
• Nepveu, E-mail: gn@mm.unknown